REGIOLUX SRGV Out Equipment Carriers Instructions

REGIOLUX SRGV Out Equipment Carriers

Product Information

• The DALI-2 mini multi-sensor is an input device designed for installation in luminaires with a shallow depth of only 11 mm. It operates via the DALI bus and provides information and LUX values for control purposes. This product complies with IEC 62386 part 303.

Product Usage Instructions

Safety Instructions

• Work on the mains supply should only be carried out by qualified professionals or under the supervision of qualified skilled electrical personnel.
• Disconnect the power supply before installing the device.
• This device is not designed to isolate other equipment from the mains supply.

Installation

• Before putting the device into operation, read the supplementary sheet and the operating instructions. Knowledge of these documents is necessary for the intended use.
• Mount the DALI-2 mini multi-sensor in luminaires with a depth of 11 mm. Power supply is provided via the DALI bus.

Exclusion of Interference

• If the detection area of the detector is too large or covers areas that should not be monitored, you can reduce or limit the range by using the enclosed blinds.

Self-Test Cycle

• When connecting the device to the DALI bus power, it will enter a self-test cycle for the first 20 seconds. During this time, the device does not respond to movement.

Specifications

• Product: DALI-2 mini multi-sensor
• Included Components: Blinds for range limitation
• Installation Depth: 11 mm
• Power Supply: DALI bus
• Compliance: IEC 62386 part 303

FAQ

1. Q: Who should work on the mains supply?
   A: Work on the mains supply should only be carried out by qualified professionals or under the supervision of qualified skilled electrical personnel.

2. Q: Can this device be used to isolate other equipment from the mains supply?
   A: No, this device is not designed for isolating other equipment from the mains supply.

3. Q: How can I limit the detection range of the sensor?
   A: You can use the enclosed blinds to reduce or limit the detection range of the sensor.

Wiring diagram SRGV pro08/pro09/pro13/pro14/pro47 ). SRG DALI are controlled (observe max. current strengths SRT installation instructions!). Only to be used in combination with a BMS system Compatibility must be ensured (DALI parts)

INSTRUCTION

• SRGV/750 netlife pro08
• SRGV/750 netlife pro09
• SRGV/750 netlife pro13
• SRGV/750 netlife pro47
• SRGSV/750 netlife pro08
• SRGSV/750 netlife pro09
• SRGSV/750 netlife pro13
• SRGSV/750 netlife pro47

MONTAGE

• DEMONTAGE

Safety instructions

•    Work on the mains supply may only be carried out by qualified professionals or by instructed persons under the direction and supervision of qualified skilled electrical personnel in accordance with electrotechnical regulations.
• Disconnect supply before ins talling! This device is not to be used to isolate other equipment from the mains supply. Pationstoco stein. voltage apply.
• The DALI screw clamps must not be connected to 230 VAC!
• Read this supplementary sheet and the operating instructions these dusents is part of the intended use!

Operation

• DALI-2 mini multi-sensor (input device) with only 11 mm installation depth for installation in luminaires. Power supply via DALI bus
• Addressable according to IEC 62386 Part 103 (control device). Instance 0 provides information regarding occupancy and movement for the DALI bus according to IEC 62386 part 303. Instance 1 provides LUX values for the DALI bus according to IEC 62386 part 304. Parameterisation is possible via mandatory Multimeter-Application-Controller of any manufacturer. This controller must support IEC 62386 parts 101/103/303/304

Mounting.

• Exclude sources of interference In case the detection area of the detector is too large or areas are being covered that should not be monitored, the range can be reduced or limited by using the enclosed blinds.

• Wiring diagram Schematic diagram  when connecting the detector, please respect the labelling of the terminal connections at the device!

• Self-test cycle
  During the first 20 sec after connecting to the DALI bus power, the product will enter a self-test cycle. During this time the device does not respond to movement.

• Initial operation General
  The device can be put into service directly after mounting, following the software instructions from the relevant controller manufacturer.

LED function indicators

• Shortly on
  • A Green Movement
  • B Red
  • C White
• Flashing
  • A Green
  • B Red
  • C White
  • D Red

Technical data

Settings

• via application which supports DALI multisensory (IEC 62386 parts 101, 103, 303, 304).
• Voltage
• Typ. power input
• Terminal clamps: for solid one-wire conductors
• Class / Degree of protection
• Dimensions 0 x H [mm]
• Range of coverage at mounting height Ambient temperature 1

1. across
2. towards
3. seated activities

• Monitored surface, when the detector is mounted at 2 5 ml
• mounting height and for tangential approach Mounting height min. / max. / recommended
• Housing
• Measured light output

EU Declaration of conformity
This product respects the directives concerning

1. electromagnetic compatibility (2014/30/EU)
2. low voltage (2014/35/EU)
3. restriction of the use of certain hazardous substances in electrical and electronic equipment (2011/65/EU)

Trouble shooting

• Power consumption on DALI line too high
  Please be aware of the total power consumption of all the DALI units in your system.

• Heat sources in the vicinity
  If, for example, the detector is located in the immediate vicinity of ventilation slits or a projector, the warm air currents can trigger motion detection. Place the detector at a sufficient distance from potential sources of interference such as ventilation slits, projectors, beamers etc.

  • Product page on the internet

SAFETY INFORMATION

General Safety Information

• Installation, commissioning and maintenance only by quailed electrician.
• Never perform any work on the luminaire with voltage applied. Danger to life due to electric shock!
• Electric connection must be appropriate according to all applicable standards and other national and international safety and accident prevention regulations.
• Damaged luminaires must not be operated.
• Observe and retain safety instructions and mounting instructions
• No liability is accepted for damages resulting from improper use.
• Use genuine parts only for repair.
• Ensure stability of the ceiling and fastening elements.
• The luminaire is exclusively intended for interior rooms and ambient temperatures not exceeding 25°C, unless otherwise described by labeling the luminaire

Operation of the luminaire

• Abnormal dark spots may be an indication of partial failure of LEDs. Inspect regularly and replace the luminaires affected.
• The light source (LED) of this luminaire must not be exchanged or replaced by the user.
• Exceeding the permissible ambient temperature will reduce the luminaire’s lifecycle, resulting in premature failure in extreme cases.
• Avoid condensation of the luminaire.
• Any mechanical load to the LED circuit boards is not permitted.
• LEDs can be damaged by electrostatic discharge (ESD).
• This may result in total failure. Always avoid direct contact.
• Depending on their con centration, chemicals can corrode the LED modules and lead to reduction of luminous ox,
• drift of luminous colour and/or total failure. Always avoid direct contact with acids, bases, solvents, volatile organic compounds and/or oils. Ensure sucient ventilation to prevent damage by gas release.
• Avoid ESD problems by not routing feed-through wiring directly along the wiring of the luminaire.
• Connect control inputs of dimmable luminaires with standard cables suitable for power supply voltage.

Changes to our products

• Medications, reworking, re-marking of products can have a negative impact on their technical properties, destroy them and possibly cause consequential damage to other objects.
• The manufacturer cannot be held responsible for damage caused by such changes.
  • d+ IP5x – dust nonconductive
  • d+ IP6x – dust conductive and dust nonconductive

Information for service, cleaning and disposal of luminaire

• Reglolux GmbH
• Hellinger Sir. 3
• 0-97486 KOnlgsberg/Bay.
• T 0952589-0
  • http//www.reglolux.de
  • lnfo@reglolux.de

References

• Home - B.E.G.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>