VIVOTEK FT9361-R Access Control Reader Installation Guide

June 4, 2024
Vivotek

VIVOTEK FT9361-R Access Control Reader

VIVOTEK FT9361-R Access Control Reader-fig

Physical Description

VIVOTEK FT9361-R Access Control Reader-fig2

No. Description No. Description
1 Display 2 NFC induction zone
3 Reboot button 4 Anti-Force dismantle trigger

Installation

Bracket Moumnt

  • Themountbracketwillbeavailablelater.

    1. Secure the back plate to the mount bracket using 4 M3 x 8.0mm screws.

VIVOTEK FT9361-R Access Control Reader-fig3

  1. Route cables through a hole on the wall or through the bracket. Below are the definitions for these cables.
    Lines| Name| Color| Description
    ---|---|---|---
    Line1| GND| Black| GND
    12V| Red| 12V input
    GND| Brown| GND
    12V| White| 12V input
    WG_DO| Purple| Wiegand/output DO
    GND| Blue| GND
    WG_DI| Green| Wiegand/output DO
    DC12V_OUT| Orange| 12V output
    Line2| Button_HC32| Black| Button for gate open
    Senses_HC32| Red| Senses for gate open
    Alarm_In_HC32| Brown| Alarm input
    GND| White| GND
    RS485_A| Purple| RS485 A
    RS485_B| Blue| RS485 B
    NC| NC| No connection
    NC| NC| No connection
    Relay_SW3_B| Green| Relay3 B
    Relay_SW3_A| Orange| Relay3 A
    Line3| NC| NC| No connection
    Relay_SW2_B| Black| Relay2 B
    Relay_SW2_A| Red| Relay2 A
    NC| NC| No connection
    Relay_SW1_B| Brown| Relay1 B
    Relay_SW1_A| White| Relay1 A
    NC| NC| No connection
    Relay_Lock_NO| Purple| Relay normally open
    Relay_Lock_COM| Blue| Relay normally grand
    Relay_Lock_NC| Green| Relay normally close
    GND| Orange| GND
    NC| NC| No connection
    Line4| RJ45| –| RJ45 Ethernet

  2. Mount the sensor device onto the bracket by sliding it from top down.

  3. Secure the installation by driving a screw from the bottom of the back plate.

Login and Registration

Server Configuration

  1. Network configuration: When the FT9361-R is started, proceed with network configuration. DHCP or Static IPs are applicable.

  2. erver:The FT9361-R requires a connection to a VAST FaceManager server. Click onthe Configuration button on the upper right of screen to configure a VAST Face Managerserver IP. (http://xxx.xxx.xxx.xxx:6073/3rd/vivotek/)

  3. hanging Server IP:If you need to change server IP, you need to logout and click the Settings button on the upper right corner of the screen.

Log in to the account

  1. ogin:On the first startup, credentials are required for a name and password.

Reboot

VIVOTEK FT9361-R Access Control Reader-fig9

Press the Reboot button and the machine will reboot.

Setting
Long press the screen enter the Setting modevia Password that you set in server.

Reset
Long press the screen, select “Reset”, enter the password: Az123567!. Machine will reset to factory mode.

FCC

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals