VIVOTEK AM-218 Wall Mount Bracket Installation Guide

June 3, 2024
Vivotek

VIVOTEK-logo

VIVOTEK AM-218 Wall Mount Bracket

VIVOTEK-AM-218-Wall-Mount-Bracket-prodact-img

Revision History

Rev. 1.0: Initial Release
Rev. 1.1: Updated the supported model list.

Package Contents – AM-218

I Compatible VIVOTEK Cameras
For the list of compatible cameras, refer to the table below:

AM- 520

Fixed Dome series

Direct installation:

  • AM- 525

| FD9171-HT, FD9181-HT, FE8174, FE8174V, FE8181, FE8181V, FE8191, FE8391-V, FE9181-H, FE9182-H, FE9381-EHV, FE9382-EHV, FE9191, FE9391-EV, FE9582-EHNV

FD9371- EHTV, FD9371-HTV, FD9381-EHTV, FD9381-HTV, MS8392-EV, FD9365-(E)HTV, FD9365-(E)HTV-A, FD9367-(E)H(T) V, FD8377-(E)HTV, FD9387-(E)H(T)V, FD9387-(E)HTV-A, FD9391- EHTV, FE9380-HV, FE9382-EHV-v2

---|---
Direct installation:

  • AM- 527

| FD9171-HT, FD9181-HT, FD9165-HT, FD9165-HT-A, FD9167-H(T), FD8177-HT, FD9187-H(T), FD9187-HT-A
---|---
Direct installation:

  • AM- 528

| FD9189-H(M)(T), FD9389-(E)H(M)(T)V, FD9368-HTV, FD9388-HTV

For details about mounting cameras to the AM-520, AM-525, and AM-527 brackets, refer to their Installation Guides.
For cabling and configuration details with each network camera, please refer to their documentation.

Installation

IMPORTANT

The AM-218 has to be installed with the AM-719. You should also purchase the AM-719 conduit box and corresponding AM-520, AM-525, and AM-527 adapter.

Mounting Hole Definitions for AM-719VIVOTEK-AM-218-Wall-Mount-Bracket-
fig-2

Refer to the table below for the description of the included screws

Screw Description| No. of

screws

| Material char.
---|---|---
M5X14| 4| Stainless steel, hex and crosshead

NOTE:

  1. It is presumed that this wall-mount bracket is installed with a hole drilled on the wall for routing power lines, DI/DO, and Ethernet cables.
  2. Route cables before you secure the wall-mount bracket to a wall.
  3. For details on the cable connections with each camera, please refer to their Quick Installation Guide.

Wall Mount Installation
Use the included alignment sticker on a preferred position. Drill holes on the wall and install the junction box. If space behind the wall allows, you may also pass cables through the wall. Note that an NPT pipe is still recommended if the connection goes through a wall. Make sure water can not enter the drilled hole. Use silicon or caulk the drilled hole to prevent water leakage. .VIVOTEK-AM-218-Wall-Mount-Bracket-fig-3

IMPORTANT:

The screws and mounting surface must be able to support a weight of 5 kg.

A 3/4″ conduit is required for routing the cables with waterproof connection. The cable gland and conduit are user-supplied.VIVOTEK-AM-218-Wall-Mount-
Bracket-fig-4

Install the cable gland and pass cables through it. Form a drip loop when routing with the conduits.VIVOTEK-AM-218-Wall-Mount-Bracket-
fig-5

Installing the Bracket and Adapter

  1. Route cables through the AM-218 bracket and the adapter (AM-520/AM-525/AM-527/AM-528).
  2. Secure the bracket to the conduit box using the included hex screws.
  3. Secure the adapter by turning them clockwise. When done, fasten the hex socket screw to secure the connection.VIVOTEK-AM-218-Wall-Mount-Bracket-fig-6
  4. Follow the instructions in the Installation Guide that came with the adapter to install network cameras.VIVOTEK-AM-218-Wall-Mount-Bracket-fig-7

Pole mount and corner mount are also supported. Please refer to their Installation Guides for more information.VIVOTEK-AM-218-Wall-Mount-Bracket-
fig-8

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals