SALTO ESD9 Keyless Door Lock User Manual
- June 15, 2024
- SALTO
Table of Contents
Compliance
PRODUCTS DESCRIPTION
| PRODUCT | TECHNOLOGY | SOFTWARE |
|---|---|---|
| COMMERCIAL NAME | MODEL | RFID 13.56MHz |
| Output max. power | CONTROL CIRCUIT | |
| SMART ESD | ESD9 | +25 dBm |
| ESD9ONLINE | +25 dBm | 0010 |
EU DECLARATION OF CONFORMITY
Hereby, SALTO Systems S.L. (Arkotz Kalea (Pol. Lanbarren), 9 – 20180 Oiartzun–
Spain), declares that this access control equipment is in compliance with the
essential requirements and other relevant provisions of Directive 2014/53/EU
(RED) and 2011/65/EU (RoHS). You will be able to find a copy of the original
declaration of conformity at the following Internet address:
https://www.saltosystems.com/certificate
UKCA DECLARATION OF CONFORMITY
Hereby, SALTO Systems S.L. (Arkotz Kalea (Pol. Lanbarren), 9 – 20180 Oiartzun–
Spain), declares that this access control equipment is in compliance with the
essential requirements and other relevant provisions of The Radio Equipment
Regulations 2017 and RoHS Regulation 2012. You will be able to find a copy of
the original declaration of conformity at the following Internet address:
https://www.saltosystems.com/certificate
UK importer contact information:
Salto Systems, Ltd. Unit 1, The Court Holywell Business Park, Northfield Road,
CV47 0FS Southam, UK.
ELECTRICAL WARNINGS
Distance between this device and human body must be higher than 20 cm.
MECHANICAL WARNINGS
The environmental conditions mentioned in the data sheets are always referred to non-condensation situations. The SALTO product should be treated with care during the installation process to avoid any aggressive contact that may damage the unit. Do not bring the device into contact with oil, paints or acids. If you have questions or doubts on this, please contact your authorized SALTO supplier.
LEGAL WARNINGS
The user shall be responsible for the correct use and maintenance of the access control equipment according to the instructions herein. SALTO shall not be responsible for any defect, malfunction, loss or damage, whether direct or indirect, caused by or arisen from any improper installation or utilization of the equipment or which contravenes, transgresses or infringes in any manner the above mentioned instructions. SALTO’s liability concerning the equipment is limited to the warranty provided. The warranty does not cover product failures due to repairs, modifications or product manipulations performed in the access control equipment or in the inner electromechanical structure by anyone other than authorized SALTO dealers or personnel.
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
We, SALTO Systems, S.L., hereby declare that the equipment bearing the model
number specified above was tested conforming to the applicable FCC Rules.
Responsible Party – U.S. Contact Information
Salto Systems Inc. USA. 1780 Corporate Drive, Suite 400. Norcross, GA. 30093.
v.kourelos@saltosystems.com
ISED COMPLIANCE STATEMENT
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Changes
or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to ICES-003.
SALTO SYSTEMS S.L. www.saltosystems.com
227559-ED.1-02/05/2023
Pol. Lanbarren, c/Arkotz nº9, 20180 Oiartzun, Spain.
All contents current at time of publication. SALTO Systems
S.L. reserves the right to change availability of any item in this catalog
its design, construction, and/or materials.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>