ET2 E42018-90AL LED Mirror Instruction Manual
- June 15, 2024
- ET2
Table of Contents
Contemporary
Lighting
PRODUCT NAME: LED MIRROR
ITEM NUMBER: E42018-90AL
E42018-90AL LED Mirror
Please consult your electrician for installing fixture and wiring.
Light
Source : Integrated LED 42W
Dimming and Color Temperature Change Instructions:
This LED fixture is compatible with wall dimmer switches.
Light output can ONLY be adjusted by using the wall dimmer switch.
The touch symbol on mirror face only control light’s ON/OFF, and color
temperature selection.
- To change the color temperature of the light by touching touch symbol on mirror face.
General Lighting (Including AC LED)
Before Getting Started
Read the instructions carefully prior to assembling the product.
When you open the package with a sharp tool like a cutter knife, be careful
not to damage the components inside.
Carefully remove all packaging materials and retain for future use.
Keep all hardware parts and packaging out of reach of small children.
Choose a clean, level, spacious assembly area.
Avoid hard surfaces that may damage the product.
Ensure that you have all required contents for complete assembly.
Take care when lifting. Assemble the product in close proximity to where you
intend to position the item.
Do not over tighten the screws and bolts as this may damage the threads.
Do not let children play with this product.
Risk of suffocation! Keep any packaging materials away from children.
GENERAL Lighting Instructions
Carefully read through the instruction sheet before assembly and using the
product.
Caution there is a risk of shock. Disconnect from power source before
assembling or cleaning.
Switch off, unplug and allow bulb to cool before replacing bulb or cleaning.
Only use the recommended bulb type and do not exceed the maximum wattage as it
could cause fire.
Do not plug the product in if cord is torn or frayed.
Cleaning & Maintenance
On polished finishes, often using talc powder reduces the appearance of
fingerprints and other smudges.
For respective shade surfaces, use the appropriate cleansers, i.e. glass
cleaner, acrylic polish, and wood polish.
Clean with soft cloth and a mild detergent.
DO not use abrasive cleaner.
Periodically (every 90 days) make sure that the screws are fully tightened.
Prolonged exposure to heat sources may cause glazing, melting and scorching,
or even cause color to fade.
Contents
Before getting,started,ensure the package contains the following
components:
| A | LED MIRROR | x1 |
|---|---|---|
| B | ANCHOR | |
| Length 1.4” (36) | x4 | |
| C | WIRE NUT | x3 |
| D | SCREW | |
| St4 *30 | x4 | |
| E | PYB050V0120LXD1P| x1
F| MOUNTING TEMPLATE PAPER| x1
IMPORTANT:
- Turn off the power at the main fuse or circuit breaker box before starting installation
- This mirror can be mounted over an electrical outlet box or on the wall and plugged into an outlet
- Carefully remove all parts from the box, and place on a flat surface. Throughout the assembly, be careful to avoid scratching the surface of the mirror.
Cleaning &
Care:
Clean glass with household glass cleanser.
Standing on Floor
- Clear the area of the floor where the mirror will be stood up on and ensure that the floor is completely flat.
- Unfold the legs (D) at the back of the mirror. Ensure that legs are locked by (X2) wing nut(E)
- Plug cord into closest power outlet.
Wall Hanging
-
Place the wall template or the mirror on the wall in the location selected for the mirror. Make sure the wall template or mirror is level and in the correct position. Secure the wall template to the wall then mark location of the 4 wall anchors(A) as indicated on the template from the wall.
Remove the wall template from the wall. -
Create holes on wall marks and screw the (X4) wall anchors (A).
-
Secure (X4) nails (B) into (X4) wall anchors (A).
-
Hang (X4) wall hangers (C) on the back of mirror onto (X4) nails (B). If wall is not mounted parallel to floor, repeat step 4.
-
Plug cord into closest power outlet. OR before step 4, cut the plug and connect the wire with junction box wire.
*IMPORTANT SAFETY INSTRUCTIONS This mirror has a 3 pins plug, once the plug is cut, the 3 core wire (phase/neutral/ground) will be exposed then can connect with phase/neutral/ground which come out from junction box.
MADE IN CHINA
Documents / Resources
| ET2
E42018-90AL LED
Mirror
[pdf] Instruction Manual
E42018-90AL LED Mirror, E42018-90AL, LED Mirror, Mirror
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>