AG9-42-US1.0 Dual Monitor Mount Instruction Manual
- June 15, 2024
- Mount
Table of Contents
- AG9-42-US1.0 Dual Monitor Mount
- Product Information
- Specifications:
- Assembly Steps
- FAQ
- Q: What is the weight capacity of the Premium Dual Monitor Desk
- Q: Are all the hardware included in the package necessary for
- Q: Is it safe to use the product for monitors over its load
- Q: Can I mount the Premium Dual Monitor Desk Mount on any type
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
AG9-42-US1.0 Dual Monitor Mount
Product Information
Specifications:
- Model: AG9-42-US1.0
- Weight Capacity: 2.2~37.5 lbs (1~17kg) per monitor
- Includes: Base, Lower Arm (x2), Upper Arm (x2), VESA Plate
(x2), C-Clamp, Support Plate, Grommet Plate, Decorative Cover, Pad
(x4), Bolt (x4), Brace, 3mm Allen Key, 4mm Allen Key (x2), 6mm
Allen Key, Metal Sheet (x4), M4x12mm Bolts (x8), M4x25mm Bolts
(x8), M5x12mm Bolts (x8), M5x25mm Bolts (x8), M6x12mm Bolts (x8),
M6x25mm Bolts (x8), Washer D5mm (x8), Spacer H5mm (x16)
Product Usage Instructions
Assembly Steps
Warm Tips: You could also refer to the Video
Guide about installation on our product page. If you need to mount
the USB, please follow the steps below first.
Option A:
-
First, detach Brace (E1) from C-Clamp (E) using the 4mm Allen
Key (L). -
Mount Brace (E1) to the bottom of Base (A) by tightening Bolts
(J) with the 4mm Allen Key (L). -
Apply Pads (I) to the base bottom to avoid desk scratches.
-
Attach the C-Clamp (E) to the Brace (E1) and tighten the Bolts
(E4) with the 4mm Allen Key (L). -
Attach the Support Plate (F) to the bolts of C-Clamp (E).
-
Secure the stand to the desktop by tightening Bolts (E3).
-
Finally, attach the Decorative Cover (H) to the base.
Option B:
-
Mount Grommet Plate (G) to Base (A) bottom with Bolts (J) and
tighten using the 4mm Allen Key (M). -
Apply Pad (I) to the base bottom to avoid desk scratches.
-
Detach two Bolts (E3) from C-Clamp (E) using the 4mm Allen Key
(M). -
Run two Bolts (E3) through Support Plate (F) and Grommet Hole
on the desktop. -
Tighten the Bolts (E3) with the 6mm Allen Key (M).
Note: Please note that the sidewith two set
screws is installed on the base (C) when installing the lower arm
(B) to the base (C). Just lock the lower set screws. DO NOT tighten
the screws excessively or it might be stripped.
If Necessary:
If the metal sheet on the plastic sleeve is loose, you can use
spare metal sheet (N) for Installation as shown in the diagram.
FAQ
Q: What is the weight capacity of the Premium Dual Monitor Desk
Mount?
A: The weight capacity is 2.2~37.5 lbs (1~17kg) per monitor.
Q: Are all the hardware included in the package necessary for
assembly?
A: Not all hardware included will be used. Please refer to the
assembly steps and diagrams for the specific hardware required.
Q: Is it safe to use the product for monitors over its load
capacity?
A: No, using the product for monitors over its load capacity may
cause damage or serious injury. Please ensure that you do not
exceed the weight capacity specified.
Q: Can I mount the Premium Dual Monitor Desk Mount on any type
of desk?
A: The desk mount can be mounted on most desks, but please
ensure that the desk is suitable and can support the weight of the
monitors and the mount.
Premium Dual Monitor Desk Mount
Instruction Manual
VESA 75×75mm / 100×100mm
KG
(1-17kg) ×2 (2.2-37.5 Ibs) ×2
If you have any questions, please feel free to contact our customer service via Amazon.
AG9-42-US1.0
WARNING!
If you have any confusions or are not quite sure about the installation,
please do not hesitate to ask for our help via Amazon.
Before assembly, please check and make sure all necessary accessories are
included and undamaged. Improper installation, such as use the product for
monitors over its load capacity or for any purpose not explicitly specified,
may cause damage or serious injury. We would not be liable for any damage or
injury caused by improper mounting or inappropriate use.
The kit contains small items that could be choking hazards if swallowed.
Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION
IS REQUIRED.
PACKAGE CONTENTS
A (x1) Base
B (x2) Lower Arm
C (x2) Upper Arm
D (x2) VESA Plate
E (x1) C-Clamp
F (x1) Support Plate
All are included in E
G (x1) Grommet Plate
H (x1) Decorative Cover
I (x4) Pad
J (x4) Bolt
E1 Brace
E2 Clamp
E3 (x2) E4 (x4)
Bolt
Bolt
K (x1)
L (x1)
3mm Allen Key 4mm Allen Key
M (x1) 6mm Allen Key
N (x4) Metal Sheet
M-A (x8) M4x12mm M4x25mm
M-B (x8) M5x12mm M5x25mm
(2.2~37.5 lbs)x2 (1~17kg)x2
DO NOT EXCEED WEIGHT CAPACITY.
M-C (x8) M6x12mm M6x25mm
M-D (x8) Washer D5mm
M-E (x16) Spacer H5mm
NOTE: Not all hardware included will be used.
01
ASSEMBLY STEPS
Warm Tips You could also refer to the Video Guide about installation on our
product page. If you need to mount the USB, please follow the steps below
first.
Loosen
Tighten
02
OPTION A:
Firstly detach Brace (E1) from C-Clamp (E) with 4mm Allen Key (L). Mount Brace
(E1) to the bottom of Base (A) by tightening Bolts (J) with 4mm Allen Key (L).
L
Loosen
A E1
E1 J
L
Apply Pads (I) to the base bottom to avoid desk scratches. Attach the C-Clamp (E) to the Brace (E1). Then tighten the Bolts (E4) with 4mm Allen Key (L).
I
Tighten
M E4
0.59-1.97″ 15-50mm
03
1.97-3.15″ 50-80mm
Attach the Support Plate (F) to bolts of C-Clamp (E). Secure stand to the desktop by tightening Bolts (E3). Finally attach the Decorative Cover (H) to the base.
F
M
H
OPTION B:
Mount Grommet Plate (G) to Base (A) bottom with Bolts (J) and tighten by 4mm
Allen Key (M). Apply Pad (I) to the base bottom to avoid desk scratches.
A
I
G J
M
Detach two Bolts (E3) from C-Clamp (E) by using 4mm Allen Key (M). Run two
Bolts (E3) through Support Plate (F) and Grommet Hole on desktop, then tighten
the Bolts (E3) with 6mm Allen Key (M).
ØØ620.-3860-m3.m15″ 0.98-1.77″ 25-45mm
E3 M
Loosen
F E3 M
04
Tighten
Install the Lower Arm (B) and the Upper Arm (C) to the Base (A). Secure the arm by tightening the set screws using 3mm Allen Key (K).
Note: Please note that the sidewith two set screws is installed on the base (C) when installing the lower arm (B) to the base (C).
Just lock the
K
lower set screws.
DO NOT tighten the screws excessively or it might be stripped.
DO NOT tighten the screws excessively or it might be stripped.
K
Insert
Attach
N
Plastic Sleeve
B
If Necessary
If metal sheet on plastic sleeve are lose, you can use spare metal sheet (N)
for Installation as shown in diagram.
05
OPTION A: Flat Back Monitor
Attach the VESA Plate (D) to back of monitor and secure it with Screws (M-A or
M-B or M-C) and Washers (M-D) using 4mm Allen Key (L).
TOP OF MONITOR UP
D
Please make sure you don’t tighten the screws much excessively or it may cause
your monitor damage.
L
M-A M-B M-C M-D
(Not for M6)
OPTION B: For Recessed / Curved Back Monitor
Attach the VESA Plate (D) to back of monitor and secure it with Screws (M-A or
M-B or M-C), Washers (M-D) and Spacers (M-E) using 4mm Allen Key (L). Put 4
spacers between VESA plate and monitor. Install 4 long screws through VESA
plate, spacers to monitor via mounting holes.
TOP OF MONITOR
UP
D
06
Please make sure you don’t tighten the screws much excessively or it may cause
your monitor damage.
L
M-A M-B M-C M-D
(Not for M6)
M-E
(One or two piece)
TOP OF MONITOR
Remove Pull
Important Notice: The pressure of the gas spring is initially set at the lowest value. So when the monitor is hung on, make sure you hold it with both hands and DO NOT let it go down suddenly.
Note: If you want to remove the monitor, pull the lock plate back and lift the monitor to separate the monitor from the arm.
Problem: If monitor faces down.
Solution: 1. Slightly loosen two preassembled bolts. 2. Adjust monitor to your
desired tilt angle. 3. Retighten both bolts to secure the
monitor in place.
M
07
For intended functioning of the mount, you may need to adjust the tension of
Arm (C) in accordance with your monitor weight by 6mm Allen Key (M).
M
Note 1:
Be sure to keep the arm in a horizontal position during adjustment. Or else it
would be difficult to adjust the mount or damage the mount.
CAUTION
Situation 1: Arm falls down Upper Arm with monitor falls down and fails to
stay where intended.
Solution: Turn the inside screw counterclockwise(“+”direction) to increase gas
spring tension until the arm can stay as intended.
Situation 2: Arm rises up Upper Arm with monitor rises up and fails to stay
where intended.
Solution: Turn the inside screw clockwise(“-“direction) to decrease gas spring
tension until the arm can stay as intended.
Note 2: For how many circles the screw should be turned, please refer to the table below.
Monitor Weight
2.2 lbs
4.4 lbs 6.6 lbs 8.8 lbs 11 lbs 13.2 lbs 15.4 lbs 17.6 lbs
Circles (AT LEAST)
min
2
3
4
5
6
7
9
Monitor Weight 19.8 lbs 22 lbs 24.3 lbs 26.5 lbs 28.7 lbs 30.9 lbs 33.1 lbs 35.3 lbs 37.5 lbs
Circles (AT LEAST) 10 11 12 14 15 17 18 20 21
08
Remove
Push Remove the cable cover from lower arm
as shown in the diagram.
Attach
Insert Run cables through the cable cover, then insert
and slide the cover down for reattachment.
09
Push
Loosen
Loosen the preassembled bolt on the Upper Arm to detach the cable cover.
Attach
Tighten
Route the cables into the cable cover and secure cable cover by tightening the bolt.
Adjust as Desired
Tilt Swivel Rotation Height
±90° Rotation
+25°
Tilt
-25°
Swivel ±90°
Swivel ±180°
±90° Rotation
+25°
Tilt
-25°
Swivel ±135°
DESK
DESK
Please do not move stand outside desk for safety!
±90° Rotation
This function works better for monitors with the center of gravity.
Note: To ensure stability, the tightness of the rotating axis has been preset,
so it would be kind of difficult to rotate the VESA plate. Suggestion: Please
attach the monitor first, then hold the two sides of it with both hands, and
rotate vigorously. If that doesn’t work out, please do not hesitate to ask for
our help via Amazon.
10
Product Dimensions
Unit Conversion
1 CM0.39 inch
Swivel
Swivel
±90°
±180° 255~304mm
70mm 2.76″
10~12″
+25°
Tilt
-25°
Swivel
±135° 207mm 8.15″
75mm 100mm
2.95″ 3.94″
±90°
Rotation
320mm / 12.6″ 255~575mm
10~22.6″
76mm/3″
25-45mm 0.98-1.77″
15-80mm 0.59-3.15”
CAUTION AND MAINTENANCE:
Don’t allow children to climb, stand, hang, or play on any part of monitor or
stand. This product is intended for indoor use only. Using this product
outdoors may lead to product
damage or personal injury. Check if that the bracket is secure and safe to use
at regular intervals
(at least every three months).
11
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>