B42 Series Wireless Headphones User Manual

: June 4, 2024
: Headphones

Table of Contents

B42 Series Wireless Headphones
BLUETOOTH PAIRING
LED INDICATORS
FCC Information
Documents / Resources

Model: B42 Series
Wireless Headphones
CHARGE BEFORE USE

B42 Series Wireless Headphones

CHARGING THE HEADPHONES – MUST ALWAYS BE CONDUCTED BY AN ADULT

USB-C charging cable (included) B42 Series Wireless Headphones - Fig
1

USB-C AC adaptor (not included)

POWER ON/OFF

Press and hold the Multi-Function Button (MFB) to turn the headphones ON/OFF.

VOLUME SWITCH

Use the volume switch to select High, Medium, or Low. The unit is factory set to Low, which is the recommended listening level.

BLUETOOTH PAIRING

MUST ALWAYS BE CONDUCTED BY AN ADULT
When the headphones are ON, they will automatically enter pairing mode.
Select ‘KIDdesigns B42’ on your Bluetooth-enabled device to connect.
A voice prompt will sound to indicate pairing is complete. Headphones will automatically connect to your Bluetooth device whenever it is in range. To reset Bluetooth, press and hold the MFB for 10-12 seconds while the unit is OFF.

LISTENING TO AUDIO

Press the MFB to play/pause the audio. Use the controls on your device to navigate tracks.

AUX CABLE

Use a 3.5mm aux cable (not included) for optional wired listening. Connect one end of the aux cable to your device and the other end to the AUX jack on the B42 headphones. (Please exercise caution and use adult supervision when using an aux cable, greater than 300mm (12 inches) for wired listening.)

LED INDICATORS

LED flashes blue while in Bluetooth pairing mode and glows solid blue when connected.
LED flashes red when the battery is low, glows solid red while charging, and turns off when the headphones are fully charged.
ONE YEAR LIMITED WARRANTY – For product support and warranty please visit: www.kiddesigns.com/support
THIS IS NOT A TOY.

To prevent possible hearing damage, do not listen at high volume levels for long periods.

FCC Information

FCC ID: EMOB42A
IC: 986B-B42A
HVIN: B42a
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3 (B) / NMB-3(B)

ISED statements
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.
This device complies with ISED RF exposure requirements, users can obtain Canadian information on RF exposure and compliance.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

WARNING: For your safety, do not use headphones if they would prevent you from hearing warning sounds, such as while riding a bike, crossing the street, etc.
IMPORTANT SAFETY INSTRUCTIONS

Do not use or charge this product near a water source, and clean only with a dry cloth. Do not block any ventilation openings. Keep product away from heat sources. Only use accessories specified by the manufacturer. Never leave it unattended when charging.

GENERAL BATTERY PRECAUTIONS

Never use or charge a battery if it appears to be leaking, or in any way abnormal. Avoid charging the battery when the temperature is not within 5°C – 35° C (41° – 95° Fahrenheit). Never expose a battery to any liquid, or to excessive heat such as direct sunlight or fire. Always keep batteries out of the reach of
infants and small children. Always charge lithium devices on a non-flammable surface – wooden tables/ carpeted floors are not recommended charging surfaces.

WARNING/DISPOSAL OF UNIT

Do NOT attempt to change or disassemble the built-in battery. Doing so will void the warranty and could cause personal injury and damage to your device. Do not dispose of batteries in the household trash or fire. Always dispose of used batteries/electronics in accordance with the prevailing community
regulations. To find a drop-off location near you, visit www.call2recycle.com

XX-B42 IB (English)
Size: 120 x 150 mm
Printing color: Black (1C + 1C)
Material: 85 gsm wood Free paper
Feb. 07, 2022