Peiying PY-DVR012 Car DVR With Rear Camera Owner’s Manual
- June 1, 2024
- Peiying
Table of Contents
Car DVR with
rear camera
PY-DVR012
Owner’s manual
Safety instruction
Read this instruction manual and keep it for future reference. Producer does not take responsibility for damages caused by inappropriate handling and use of the product.
- Protect this device from humidity, water and other liquid. Avoid using/storing it in extreme temperatures. Do not expose it to direct sunlight and other sources of heat.
- This appliance may be used by children who are above 8 years old and by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they are supervised and guided by a person who is responsible for their safety in a cautious manner for all the safety precautions being understood and followed. Children should be supervised to ensure that they do not play with the appliance. Children should not perform cleaning and servicing of the device unsupervised.
- Keep the device out of the reach of children.
- Do not expose this device to direct sunlight for a long time.
- If the device was not used for a long time, charge it for at least 10 minutes before use.
- Use only authorized accessories.
- Always disconnect the product from the power source before cleaning.
- Clean this device with a soft, slightly damp cloth. Do not use any chemical agents to clean this device.
- Do not attempt to repair this device yourself. In case of damage, contact authorized service point for check-up or repair.
- Turn off the device before ejecting SD card. Otherwise, data on the SD card may be damaged or removed.
Product description
1. Speaker | 8. Holder socket |
---|---|
2. Camera lens | 9. AV socket |
3. MicroSD card slot | 10. Menu button |
4. Reset button | 11. Down button |
5. Display | 12. Power/OK button |
6. Power indicator | 13. Up button |
7. USB-C socket | 14. Emergency recording button |
Mounting the device
Dashcam:
- Put the suction cup holder into the holder socket in the dashcam.
- Clean the mounting area (front windscreen) and hold the suction cup against the windscreen.
- Twist the holder’s lever into the locked padlock position.
- Plug one end of the car charger into the USB-C socket in the dashcam, plug another end into the vehicle’s cigarette lighter socket.
Note: Place the cable in a way, that it does not disturb the driver while driving.
Rear camera:
Before installation, choose the correct place for mounting. Mounting place has
to be installed in a way, that it does not obstruct field of view.
Rear camera can be installed in two ways:
- On mounting tape. Peel off first piece of paper from the tape and stick it to the camera’s mounting bracket. Peel off second piece of paper from the tape and stick the camera do selected place.
- On screws. Drill the holes in selected place and screw in the camera.
During drilling make sure, that no damage is done to any wire, especially for safety systems.
After connecting the 2,5 mm plug to the AV socket in the dashcam, the view from rear camera will appear on the display. If red wire will be connected to the reversing lights (for example with quick connector), after shifting into reverse gear, the view from rear camera will be enlarged, helping the driver with maneuvering the vehicle.
Note: for this function to work, the red wire has to be connected to the same electrical installation.
MicroSD card installation
- Place the microSD card in the proper slot of the device and press gently, until it clicks. Make sure, that the card is installed in correct way.
- To take out the card, press it gently. When the card slides out of the slot, take it out.
Notes:
- The microSD card in the device will be treated as storage device. It is advised to format it first.
- Use microSD cards with class 10 or higher, with maximum capacity of 256 GB.
Turning on and off
-
To turn on the device:
• Press and hold the power button
• If the dashcam is connected to the cigarette lighter socket, the camera will turn on automatically after ignition and start recording. -
To turn off the device:
• Press and hold the power button
• If the camera is connected to the cigarette lighter socket, after turning off the engine, the dashcam will turn off after 5 seconds.
Operation
-
To start or stop the recording press the power button.
-
Press the menu button to go to setting menu or to cancel selection.
-
Press and hold the menu button to go to settings menu.
-
Press the OK button to confirm options.
-
Use the up and down buttons to navigate the menu.
-
Press the up button to take a picture (in recording mode).
-
Press the down button to switch on or off the sound recording.
-
Press the emergency recording button to lock currently recorded video (recording in this mode is indicated by the yellow recording indicator).
These videos will be locked and will not be overwritten. -
In order for camera to turn on and start recording after shake, turn on the Parking guard on (in the recording menu). Select the desired sensitivity of the function in the G-sensor menu.
Dashcam settings
- Resolution: change the resolution of recorded videos.
- Loop recording: change the duration of recorded videos.
- Screen saver: turn on the option to turn off the screen after selected duration of time (camera will keep working).
- Frequency: change the frequency of the recordings.
- Language: change the language of the menus.
- Audio: record the voice.
- Motion detection: record video automatically after detecting the moving.
- Parking mode: turn on the parking mode.
- Date and time: change the date and time settings.
- Volume: set the sound volume.
- Format: erase all data currently on the microSD card.
- Time zone: set the time zone.
- Default settings: reset all settings to factory values.
- Version: displays current version of software.
Troubleshooting
Problem | Possible solution |
---|---|
Cannot record or take pictures | Check if the card is locked and if it has |
sufficient space.
Recording ending automatically| Use microSD card of class 10 or higher
“File error” during playing thevideo or picture| Error occurred during saving
the file, please format the memory card.
Blurry picture| Clean the lens of the dashcam
The device froze| Press the Reset button To do it, use thin object, for
example, a paper clip
SPECIFICATION
-
Display: 3″ (640 x 480 px)
-
Chipset: GC2093
-
Lens: 170° wide angle lens
-
Video resolution:
◦ Front camera: 2.5 K (25 FPS), 1080p (25 FPS)
◦ Rear camera: 1080 p (25 FPS) -
Video format: TS
-
Max. photo resolution: 12M (1920 x 1080 px)
-
Photo format: JPG
-
Automatic recording after ignition
-
Recording mode: loop recording
-
Memory card reader: micro SD (max. 256 GB)
-
USB port: USB-C
-
Functions: motion detection, G-Sensor, taking photos, seamless recording
-
Parking monitor (hardwire kit required)
-
Power supply: 2 uF capacitor
-
Power voltage: 5 V / 2 A
-
Weight: 110 g
-
Dimensions: 95 x 53 x 36 mm
-
In set: rear camera, holder with suction cup, car charger, user’s manual
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate
collection systems) This marking shown on the product or its literature,
indicates that it should not be disposed with other household wastes at the
end of its working life.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources. Household
users should contact either the retailer where they purchased this product,
or their local government office, for details of where and how they can take
this item for environmentally safe recycling. Business users should contact
their supplier and check the terms and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
Made in China for Lechpol Electronics Leszek Sp.k., ul. Garwolińska 1,
08-400 Miętne.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>