Headphones B3S Wireless Headset User Manual
- October 30, 2023
- Headphones
Table of Contents
B3S Wireless Headset
User Manual
Specifications
Frequency Response: 20-20KHz
Max Output Power: 20mW
Working Range: 8∼10m
Battery voltage: 3. 7V
Battery capacity: mAh
Battery Charging Voltage: DC4.2-5.5V
Charging lime: about 2H
Working lime: about 12H
Impedance: 32 ohm
Sensitivity: 110+/-3dB
Speaker diameter: 40mm
Button Function
-
“POWER” Power on/Power off
-
“ + ” Volume up: short press
Move next: long press -
“ – ” Volume down: short press
Move previous: long press
Function Description
- Power on: Long press “POWER” for more than 3 seconds, the headphone tum on and enter Btuetooth Mode. The blue and red light; flash altemately.
- Power off: Long press “POWER” for more than 3 seconds, the LED indicator light is off and the headphone turn off.
Button Guide
- Hang on: Short press “POWER” button when being called
- Hang up: Short press “POWER” button when calling
- Dial back: Double click “POWER” button
- Play music: Normally short press “POWER” button to turn on the smart devices automatically to play music
- Continue to play music after the call: When the an is an incoming call, the music will be automatically suspended. After the call, you need to short press the “POWER” button to continue playing.
Btuetooth mode
Repairing: turn off the Bluetooth function of the connected smart
devices, at this time, the Bluetooth headset and the last matching device got
disconnected. LED light flashed between red and blue.and enter the Bluetooth
pairing mode.then tum on the Bluetooth function of the smart devices. search
the device named “E96” to get connected without a password, after pairing
successfully, voice prompts “connected”, the blue LED is on and flash slowly
after working.
Subsequent pairing: 3 seconds after powering on, it will automatically search
and connect the smart device which paired last time.
Warning voice of maximum volume: “Didi”
Power saving mode:headset will automatically power off after pairing
continuously for 5 minutes; it will cut off power supply automatically after
using Aux-in cable for power saving.
LED indicator
Charging | The red LED is on, when full chanrged, the blue LED is on |
---|---|
Powering on | Blue LED is on |
Powering off | Red LED flashes and finally turn to off |
Pairing | Blue and red LED flashes alternately |
Connected | Blue LED flashes |
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital, pursuant to Part 15 or the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications, However, there is no
guarantee that interference will not occur in a particular installation If the
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
INSTRUCTIONS
-
KeyOperating Instructions
– ① CD Long press three seconds is power on.off
– ① CD In Wireless mode when get the calling. Short Press is answer the calls; Long Press is Refuse to listen, continuous push 2 times is redial
– ② Playing: Short Press: Play/Pause;
— ① CD In Wireless/MP3 mode, Short
Press:Previous;Long Press: volume
② In FM mode,Short Press: Previous; Long Press: volume-
– ① CD In Wireless/MP3 mode, Short Press: next; Long Press:volume+
② In FM mode,Short Press: next frequency; Long Press: volume+
M – ① Short Press to change the model, Wireless/MP3/ FM Radio -
LED Indicator
① Wireless mode: pairing status blue light flashing, after pairing the blue light slow flashing.
② In MP3 mode: the blue light will slow flashing when playing;
③ In FM mode: When listening to the radio station blue light. search radio flashing.
④ In charging mode: the red light will be on for a long time when charging, and the blue light will be displayed after charging. -
LINE Connecting TO Audio Jack
① Insert audio line, Go directly to the AUX LINE IN pattern, at this time for ordinary headset headphones, buttons
② Support mobile phone/iPod/MP4/MP3/CD/PC, etc -
Funcitional Parameter
1. USB charge: DC5VIN
2. SNR: 88Db
3. FM frequency: 87.5-108MHz
4. Wireless distance: 10meters
5. Frequency: 50HZ-20KHz
6. Output power: 35mW
7. Wireless frequency: 2.401-2.480GHz
8. Charging time: 2hours
9. Call duration: 6hour
10. Standby time: 18hours
FCC STATEMENT:
This device companies with Part 15 of the FCC RuIes.
Operation is subject to the foIIowing two conditions:
This device may not cause harmful interference, and This device must accept
any interference received, including interference that may cause undesired
operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to company with the Iimi
is for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential instai action. This equipment generates uses and
can radi ate radio frequency energy and, if not Instasied and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference wiII not occur in a part
icuIarinsta II ation. If this equipment does cause harmfuli nterference to
radio or to levision reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate
the receiving antenna. Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. Consult the dealer or an experienced
radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>