Headphones BH10 Wireless Headset Instruction Manual
- June 5, 2024
- Headphones
Table of Contents
beurer MG 206 HD-enjoy Shiatsu Seat Cover
**
**Packing list
- BH10 Wireless headset
- Audio cables
- Charging cables
- Product instructions
Use environment requirements and product parameters
- Product model: BH10
- Charging time: 2-3 hours
- Charging voltage: 5V
- Speaker impedance: 32Ω
- Communication distance: 10 meters
- Input: 5V 0.3A
- Working temperature: 0°C～45°C
Operating instructions
Wireless Bluetooth connection
Press and hold the power button for 3-5 seconds, after the headset flashes red
and blue lights alternately, turn on the phone’s bluetooth,Search and find the
device name
“BH10” to connect. Set after successful connection The blue light flashes
slowly.
Switch on and off
Press and hold the switch button for 3 seconds, the blue light flashes, that is
The device will automatically pair and connect. Press and hold the power
button for 3-5 seconds to shut down.
Appearance buttons
-
Short press to increase the volume, long press for next song
-
Play/Pause , Answer/Hang up
-
Short press to reduce the volume, long press for Previous song
-
Type-C charge port
-
Type-C charge port
-
AUX audio port
-
Bluetooth indicator
-
Mic port
-
Long press turn on or turn off , Short press turn on logo light or turn off logo light
Charging
Use the complimentary charging cable or TYPE-C charging cable to connect to
the device. Charging process，
the red light of the middle indicator light is always on, and the indicator
light is off when the battery is fully charged. .
Wired mode
To use the wired mode, turn off the Bluetooth mode and perform shutdown
operations. Plug in and deliver
the 3.5mm audio cable is ready for use. (The headset button and microphone
cannot be used in this state.)
Buttons Description
| Button name | Action | The Effect | In view of the equipment |
|---|---|---|---|
| Power Button | Press and hold for |
3-5 seconds
| Turn on| This Machine
Power Button| Press and hold for
3-5 seconds
| Turn off| This Machine
Power Button| Short press 1 time| Turn on logo light
or turn off logo light
| This Machine
Play Button| Short press
(when music is playing)
| Play/pause| Mobile phone
Play Button| Short press
(when a call comes in)
| Answer/hang up| Mobile phone
Play Button| Long press for 3 seconds
(when a call comes in)
| Reject the phone| Mobile phone
V+ key| Short press
(when music is playing)
| Volume increase| Mobile phone
V-key| Short press
(when music is playing)
| Volume down| Mobile phone
V+ key| Long press
(when music is playing)
| Next song| Mobile phone
V-key| Long press
(when music is playing)
| Previous song| Mobile phone
Common problems
The device cannot be found
The phone cannot search for the device, try to turn off the headset and then
turn it on again, And Also try to turn off the BlueTooth of the mobile phone
and then turn it on again. The dental equipment is cleared, and the search and
pairing is performed again.
The device is connected but there is no sound
Adjust the volume of the headset, check if the volume on the headset is
adjusted to the lowest.
There is no sound from the headset when the audio cable is plugged in
Plug the audio cable back into the headset and mobile phone.
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>