M-gears MK105 BLE Keyless System Keyfob User Manual
- June 3, 2024
- M-gears
Table of Contents
MK105 BLE Keyless System Keyfob
MK105 User Manual
BLE Keyless System-Keyfob
Rev05 2022/10/7
Whayu industrial co. ltd TEL: 03-5714225
No.326, Sec. 2, Kung Tao 5 Road., Hsinchu City 30070, Taiwan (R.O.C.)
MK105 User Manual Table of Contents 1. Electrical Characteristics
………………………………………………………………………………………3
2. Product Parts Description ……………………………………………………………..3
3. Product Installation……………………………………………………………………………..6 4. Product
Instuctions ………………………………………………………………………9 5. Other product function
……………………………………………………………….13 6. NCC Interference
Statement……………………………………………………………………………….14 7. Federal Communication Commission
Interference Statement……………………………….15 8. FCC Radiation Exposure Statement:
…………………………………………………………………….15 9. USERS MANUAL OF THE END
PRODUCT:………………………………………………………………16 10. LABEL OF THE END PRODUCT:
…………………………………………………………………………16 11. Ant list
…………………………………………………………………………………………………………..16
Whayu Industrial Co., Ltd.
Revision History
Date 2022/7/1 2022/7/7
Release R01 R02
Author Lance/Justin Lance/Justin
2022/9/19 2022/9/22 2022/10/7 2022/10/7
R03
Lance/Justin
R04
Lance/Justin
R05
Lance/Justin
R06
Lance/Justin
Related Documents
Date
Author
MK105 User Manual
Description R01 Modify Block Diagram, Add PCBA Dimension Add NCC notice
information Correct Antenna Model Name Add device use instructions Remove BD
Document(s)
Whayu Industrial Co., Ltd.
1. Electrical Characteristics Item Rated Voltage Operation Voltage Range Operation Temperature Storage Temperature Standby Current BLE transmit power BLE receive sensitivty level LF frequency LF modulation scheme Battery
MK105 User Manual
Spec 3V DC 2.6~3.3V -20 ~ +80 -40 ~ +85 12uA (typ.) 6 dBm (typ.) -90dBm
(LE_1M_RX) 125K Hz OOK CR2032 x1
2. Product Parts Description
Whayu Industrial Co., Ltd.
MK105 User Manual
A. Attachment Point : : Locking point to fix the product to the body of the
vehicle.
B. Control Panel Connector : :Connector to connect the control panel and
control box
C. Control Box Connector : :Connector to connect control box
D. Vehicle Connector : :Connector to connect the product to the vehicle body
E. Buzzer : :Components that produce a corresponding beep sound when the
product is in motion
F. Control Box Ground Pin
Whayu Industrial Co., Ltd.
: :Ground wire of controller G. Steering Lock Bar : :bar for locking vehicle steering handle H. Control Panel : :Control Panel for user-operated I. Control Box : :BLE Keyless system control box assembly. J. Smart Keyfob : :Smart keyfob for keyless operation.
MK105 User Manual
Whayu Industrial Co., Ltd.
3. Product Installation
1. Remove the original main switch.
2. Keyless Keyless Fix Keyless main switch: Fix the keyless main switch to
the frame.
MK105 User Manual
3. Install the cables for the fuel tank cover and seat cushion lock: Install the cables for the fuel tank cover and seat cushion lock in the same way as the original installation.
Whayu Industrial Co., Ltd.
MK105 User Manual
4. Keyless Install the control panel: Install the control panel from the
other side and lock it to the Keyless main switch.
5. Connect the control panel connector: After fixing the control panel,
connect the control panel connector to the mating connector.
Whayu Industrial Co., Ltd.
MK105 User Manual
6. Keyless Connect the control box: Connect the control box to the Keyless
main switch.
7. Keyless Keyless Connect the Keyless main switch to the vehicle: Connect
the Keyless main switch to the vehicle body connector
Whayu Industrial Co., Ltd.
MK105 User Manual
8. Keyless
Connect the Keyless main switch ground wire to the vehicle: Attach the ground
wire to the frame metal.
9. Keyless System ! Put the shell back on, you’re done. Then enjoy all the
functions of Keyless System!
4. Product Instuctions
Smart Key (Smart keyfob button description)
Whayu Industrial Co., Ltd.
MK105 User Manual
(Control Panel function description) Keyless System Unlock Smart Key Wake (ON)
Button Keyless System Press the Wake (ON) Button of the smart keyfob to
remotely unlock and wake up the Keyless System.
Keyless System Lock Smart Key Lock (OFF) ButtonBuzzer Keyless System Smart Key
Start/Stop Button When press the Lock (OFF) Button of the smart keyfob , the
Buzzer will beep once and the Keyless System will be locked, so even if the
Smart Keyfob is within the sensor range, the Start/Stop Button on the control
panel cannot be used to wake it up.
Keyless System Wake up Keyless SystemKnob After successful authentication,
wake up the Keyless System, and then you can operate the Knob on the control
panel.
Keyless System Unlock Smart Key Wake (ON) Button Keyless System
Press the Wake (ON) Button on the Smart Keyfob to wake up the Keyless System.
Start/Stop Button Keyless System Press the Start/Stop Button on the control
panel to wake up the Keyless System.
Keyless System Lock Smart Key Wake (on) Button Keyless System ” Unlock ” Press
the Wake (on) Button on the Smart Keyfob to wake up the Keyless System and set
the system to “Unlock” state.
Whayu Industrial Co., Ltd.
MK105 User Manual
Keyless System Standby Smart Key Lock (OFF) Button Keyless System “Lock ”
Press the Lock (OFF) Button on the Smart Key to put the Keyless System into
standby and set the system to “Lock” state.
Start/Stop Button Keyless System Press the Start/Stop Button on the control
panel to put the Keyless System into standby mode.
10 Keyless System After 10 seconds of inactivity, the Keyless System
automatically enters standby mode.
Keyless System Backup Method Keyless System Smart Key When the vehicle battery
is damaged and the Keyless System does not work properly or the Smart Keyfob
battery is dead, you can use the Keyless System Backup mechanism to unlock the
vehicle and operate the vehicle.
Using the spare tool, remove the screwdriver and fix it.
Step 1
Step 2
Smart Key Remove the physical spare key from the Smart Keyfob
Keyless Knob Cap Remove the Knob Cap from the Keyless Main Switch.
Whayu Industrial Co., Ltd.
MK105 User Manual
Use the spare tool to remove the screw to reveal the spare key hole.
Unlock. Insert the spare key and turn the red dot to align with Unlock point.
Whayu Industrial Co., Ltd.
MK105 User Manual
Use the two levers of the spare gadget and insert them into the two holes.
All functions can be operated immediately.
Smart key After the vehicle is repaired or the Smart keyfob battery is replaced, the product will be restored to its original state in order.
5. Other product function
Warning of authentication failure Smart Key Start/Stop Button When the legal
Smart Keyfob is not in the sensing range, pressing the Start/Stop Button of
the control panel will not wake up and there will be a flashing red light
warning.
Whayu Industrial Co., Ltd.
MK105 User Manual
Keyless Keyless system protection mechanism 6 Keyless System Keyless System
Keyless System ” Lock ” Smart Key When 6 consecutive attempts are made to wake
up the Keyless System, the Keyless System lock warning appears and the Keyless
System is then set to “Lock” status, requiring a Smart Key to unlock it.
Backup Mechanism Alert Knob On LED Blue / Buzzer OFF LED Blue / Buzzer When
using the backup mechanism to force the Knob to the “On” position, the red
light continues to blink after the LED Blue/Buzzer warning, and when turned
back to OFF, the LED Blue/Buzzer warning again.
Smart Key . Smart Keyfob power saving mode. Smart Key Keyless SystemSmart Key
Smart Key
When the Smart Key or Keyless System is not operated for three days, the Smart
Key enters power saving mode and needs to be released by pressing the any key
on the Smart Key.
Smart Key Smart Keyfob Low Battery Alert Smart Key (2.7V)Keyless LED RED
Keyless System When the battery in the Smart Keyfob is too low (2.7V), the RED
LED of the control panel will remain on when the Keyless wakes up successfully
until the Keyless System enters standby mode.
6. NCC Interference Statement
”
Without permission granted by the NCC, any company, enterprise, or user is not allowed to change
frequency, enhance transmitting power or alter original characteristic as well as performance to an
approved low power radio-frequency devices. The low power radio-frequency devices shall not influence
aircraft security and interfere legal communications; If found, the user shall cease operating immediately
until no interference is achieved. The said legal communications means radio communications is
Whayu Industrial Co., Ltd.
MK105 User Manual
operated in compliance with the Telecommunications Management Act. The low
power radio-frequency devices must be susceptible with the interference from
legal communications or ISM radio wave radiated devices.
7. Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures: Reorient or relocate the receiving antenna. Increase the
separation between the equipment and receiver. Connect the equipment into an
outlet on a circuit different from that to which the receiver is
connected. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
8. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 0.5cm between the radiator & your body.
Whayu Industrial Co., Ltd.
MK105 User Manual
This module is intended for OEM integrator. This module is only FCC authorized
for the specific rule parts listed on the grant, and that the host product
manufacturer is responsible for compliance to any other FCC rules that apply
to the host not covered by the modular transmitter grant of certification. The
final host product still requires Part 15 Subpart B compliance testing with
the modular transmitter installed. Additional testing and certification may be
necessary when multiple modules are used.
9. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to
keep at least 0.5cm separation with the antenna while this end product is
installed and operated. The end user has to be informed that the FCC radio-
frequency exposure guidelines for an uncontrolled environment can be
satisfied.
The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
10. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following ”
Contains TX FCC ID: RUK-MK105 “. This device complies with Part 15 of FCC
rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
11. Ant list
Ant. 1
Brand M gear
Model Name NE3- 21023
Antenna Type PCB Antenna
Connector
Gain (dBi) 2.1
Whayu Industrial Co., Ltd.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>