SALTO L80 Smart Lock Instructions
- June 14, 2024
- SALTO
Table of Contents
SALTO L80 Smart Lock
PRODUCTS DESCRIPTION
| PRODUCT | TECHNOLOGY | SOFTWARE |
|---|---|---|
| COMMERCIAL NAME | **** |
MODEL
| RFID 13.56MHz
Output max. power
| BLUETOOTH LE 2400–2483.5 MHz
Output max. power
| CONTROL CIRCUIT| BLUETOOTH LE
MODULE
| SoC
FUS| Bluetooth LE
Stack
XS4 Locker E1011
| L80| +20 dBm| | 0100| | |
L90| +20 dBm| | 0054| | |
LH0| +20 dBm| | 0110| | |
L0M| +20 dBm| +6 dBm| 0206| | 0186| 0187
L0J| +20 dBm| +8 dBm| 0166| 0136| |
EU DECLARATION OF CONFORMITY
- Hereby, SALTO Systems S.L. (Arkotz Kalea (Pol. Lanbarren), 9 – 20180 Oiartzun– Spain), declares that this access control equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU (RED) and 2011/65/EU (RoHS).
- You will be able to find a copy of the original declaration of conformity at the following Internet address: https://www.saltosystems.com/certificate.
ELECTRICAL WARNINGS
Caution
- Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
- Disposal of a battery into a fire or a hot oven, or mechanically crushing or cutting of a battery, can result in an explosion.
- Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
- A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
- The distance between this device and the human body must be higher than 20 cm.
Recommended batteries
- Duracell Plus Power (AAA) LR03 MN2400
- Duracell Ultra Power (AAA) LR03 MX2400
- Varta Industrial (AAA) LR03 04003
- Varta High Energy (AAA) LR03 04903
- Varta Max Tech (AAA) LR03 MN2400
MECHANICAL WARNINGS
The environmental conditions mentioned in the data sheets are always referred
to as non-condensation situations. The product is protected with a BioCote
additive that protects it against bacteria. The SALTO product should be
treated with care during the installation process to avoid any aggressive
contact that may damage the unit. It may be necessary to loosen the trims
mounting during installation. Do not bring the device into contact with oil,
paints or acids. Do not paint the door with the electronic device already
mounted on the door. CLEANING THE ELECTRONIC DEVICE: a damp cloth with mild
soapy water can be used. Never use abrasive soaps or sprays. Note that when
the door is closed without the lock having been already programmed, the lock
will automatically lock and can only be opened with a Portable Programming
Device (PPD). If you have questions or doubts about this, please contact your
authorized SALTO supplier.
LEGAL WARNINGS
The user shall be responsible for the correct use and maintenance of the
access control equipment according to the instructions herein. SALTO shall not
be responsible for any defect, malfunction, loss or damage, whether direct or
indirect, caused by or arising from any improper installation or utilization
of the equipment or which contravenes, transgresses or infringes in any manner
the above-mentioned instructions. SALTO’s liability concerning the equipment
is limited to the warranty provided. The warranty does not cover product
failures due to repairs, modifications or product manipulations performed in
the access control equipment or in the inner electromechanical structure by
anyone other than authorized SALTO dealers or personnel.
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This product is a radio transmitter and receiver to be used in mobile conditions.
Supplier’s Declaration of Conformity
- 47 CFR § 2.1077 Compliance Information
- We, SALTO Systems, S.L., hereby declare that the equipment bearing the model number specified above was tested conforming to the applicable FCC Rules.
- Responsible Party – U.S. Contact Information
- Salto Systems Inc. USA. 1780 Corporate Drive, Suite 400. Norcross, GA. 30093. v.kourelos@saltosystems.com.
ISED COMPLIANCE STATEMENT
This device complies with Industry Canada license-exempt RSS standards(s).
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IMDA COMPLIANCE LABEL
Legend
| Remarks: | |
|---|---|
| [1] FCC | Not applicable for model L80 |
| [2] ISED | Not applicable for models L80 |
| [3] IMDA | Not applicable for models LH0, L80 |
CONTACT
- SALTO SYSTEMS S.L. www.saltosystems.com.
- Pol. Lanbarren, c/Arkotz nº9, 20180 Oiartzun, Spain.
- All contents were current at the time of publication. SALTO Systems S.L. reserves the right to change the availability of any item in this catalogue, its design, construction, and/or materials.