WIRCRACING LM16 Prototype RC Car Instruction Manual
- June 17, 2024
- WIRCRACING
Table of Contents
LM16 Prototype RC Car
Instruction Manual
INTRODUCTION
LM16 is a new generation high quality 1/10 scale touring car.
LM16 is supplied in a box,you can download the Instruction manual from
www.wircracing.com Its use is intended for more
than 16 years old persons with experience on rc model car field.
Children and all the persons without this requirement MUST have direct
supervision of a knowledgeable adult responsible.
SAFETY PRECAUTIONS
Instruction Manual MUST be read and fully understood before to start building
and operating functions.
Always keep Instruction Manual in safety place, ready to be consulted for any
reference you need. Use only original WIRC spare parts.
GENERAL INFORMATION
Assemble the kit only away from the reach of children.
Follow the building and operating instructions using the utmost care.
Don’t put any part of your body inside rotating and moving elements as this
may cause damage or serious injury.
Check and clean the model before putting it away.
Don’t use your model car in public places or in roads and areas where it could
generate conflict with person or vehicular traffic.
The model car is controlled by radio: you MUST put great care to avoid loss of
radio control always keeping a safety margin all around your model in order to
prevent any collision.
Operating frequency: check and be sure it is clear and not shared with anybody
at same time; it could cause loss of control of the RC model.
Always turn on your transmitter before you turn on the receiver in the car and
always turn off the receiver before you turn off your transmitter.
Keep the wheels of the model off the ground when checking the operation of the
radio equipment.
Disconnect the battery pack before storing your model.
WARRANTY
WIRC guarantees this model kit to be free from defects in both material and
workmanship within 30 days of purchase.
The total monetary value under warranty will in no case exceed the cost of the
original kit purchased.
This warranty doesn’t cover any compnents damaged by use or modification or as
result of wear. Part or parts missing from this kit must be reported within 30
days of purchase.
No part or parts will be sent under warranty without proof of purchase.
If you find a defective or missing part, contact the local distributor.
Customer service and support will be provided through local hobby store.
No warranties are expressed or implied that cover damage caused by what is
considered normal use or cover or imply how long any model cars’ components or
electric components will last before requiring replacement.
Due to the high performance level of this model car you will need to
periodically maintain and replace consumable components; any and all warranty
coverage will not cover replacement of any part or component damaged by
neglect, abuse or improper or unreasonable use.
This includes but is not limited to damage from crashing, excessive moistur,
improper use or no maintenance or user modifications which compromise the
integrity of components.
Warranty will not cover compnents that are considered consumable on RC model
car.
WIRC doesn’t pay nor refund on any component sent from WIRC or its distributor
for warranty.
WIRC reserves the right to make final determination of the warranty status of
any component or part Use only original WIRC spare part:
CUSTOMER SUPPORT
Please don’t hesitate to contact WIRC support at
[email protected] for any problem or question.
Also kindly visit our website www.wircracing.com
to find last updates, set-up information, option parts and other information.
World racing car s.r.l.
Via A.Volta 2 Bis
36040 Brendola (VI)
ITALY
Phone: 0039 0444 1792263
E-mail: [email protected]
Website: www.wircracing.com
TECHNICAL INFORMATION
- TRANSMISSION: 2 DRIVE WHEELS
- BODY: LEXAN FORMULA MODEL (NOT INCLUDED)
- ADJUSTABLE FRONT TOE, CAMBER AND CASTER
- ADJUSTABLE REAR HEIGHT
- UMPER/FRONT BACKSTOP
- CARBON CHASSIS 2mm
- FULL BALL BEARING
- ADJUSTABLE DIFFERENTIAL
TECHNICAL DATA
| LENGHT | 418 MM. |
|---|---|
| WIDTH | 190 MM. |
| ADJUSTABLE WHEEL BASE | 269-265MM. |
| WEIGHT CHASSIS | 1080 GR. |
ADDITIONAL ITEMS NEEDED FOR COMPLETION (REQUIRED BUT NOT INCLUDED IN THE
KIT)
TOOLS
REQUIRED
THESE TOOLS ARE NOT INCLUDED IN THE KIT BUT ARE REQUIRED FOR PROPER ASSEMBLY
NOTICE:
THE FOLLOWING ITEMS ARE NEEDED FOR COMPLETION OF THE LM16; THEY ARE NOT
INCLUDED IN THIS KIT (UNLESS NOTED) AND SHOULD BE OBTEINED FROM YOUR LOCAL
HOBBY SHOP.
BE SURE TO READ THE INSTRUCTION COMPLETELY PRIOR TO ASSEMBLY 
This part is not simmetric, make sure it’s horiented properly. 
Fit the carbon arm on the Rear
Holes (Blue).
Use the lower holes to move the support longitudinally and change wheelbase
setting:
RED – Short wheelbase, better turning but less stable
BLUE – Long wheelbase, more stable but less sharp in corners. 
SHOCK FILLING
Fully extend the piston rod so the piston is at the bottom of the shock body.
Hold the shock upright and fill the shock body with shock oil as in the
picture.
Let the oil settle and allow air bubbles to rise to the top. Slowly move the
piston up and down until no more air bubbles appear. Add shock oil as
necessary.
Pull the piston rod most of the way out of the shock bod. Let the shock rest
for 5 minutes to allow the air bubbles to scape.
P-ONE SHOCKS OIL
| CODE CST | CST |
|---|---|
| S0-350 | 350 |
| S0-400 | 400 |
| S0-450 | 450 |
| S0-500 | 500 |
| S0-550 | 550 |
| S0-600 | 600 |
| S0-650 | 650 |
| S0-700 | 700(1N KIT} |
| S0-800 | 800 |
