DEWERT OKIN CU165 RF Touch Wireless Remote Control User Guide
- June 13, 2024
- DEWERT OKIN
Table of Contents
Quick guide RF-TOUCH
HIMOLLA / Day Bed
CU165 RF Touch Wireless Remote Control
Button | Function |
---|---|
1 | Memory position 1 |
2 | Memory position 2 |
3 | Memory position 3 |
4 | Memory save button |
5 | Drive M3 up |
8 | Drive M3 down |
9 | Drive M1 up |
12 | Drive M1 down |
13 | Drive M2 up |
16 | Drive M2 down |
17 | Drive M4 up |
20 | Drive M4 down |
21 | Relaxposition |
24 | Horizontal Position |
27 | Battery indicator |
28 | Key lock |
p | Pairing button Pairing LED |
Control Unit CU165
Button & sockets
1| Drive M1 back rest
2| Drive M2 thigh rest
3| Drive M3 neck rest
4| Drive M4 foot rest
a| Pairing button
b| Pairing LED
Symbol / Button description
Note: Approx. 10 sec after the last touch of a button, the RF-TOUCH
automatically switches to standby mode, background lighting is switched off
and the key lock is activated. If an adjustment button is pressed during
standby mode, the key lock lights up blue and all other buttons white.
Key lock: Standby mode is activated by pressing the key button for
approx. 3 sec., white background illumination of all buttons confirms that the
RF-TOUCH is activated.
Drive up: The drive keeps moving and the button lights up blue as long as
this button is pressed.
Drive down: The drive keeps moving and the button lights up blue as long
as this button is pressed.
Neckrest: The drive keeps moving and the button/symbol lights up blue as
long as this button next to the symbol is pressed.
Backrest: The drive keeps moving and the button/symbol lights up blue as
long as this button next to the symbol is pressed.
Thightrest : The drive keeps moving and the button/symbol lights up blue
as long as this button next to the symbol is pressed
Footrest: The drive keeps moving and the button/symbol lights up blue as
long as this button next to the symbol is pressed.
Horizontal position: The drives keeps moving and the button/symbol lights
up blue as long as this button next to the symbol is pressed.
Memory position 1 : The drives move to the saved position. The drives
move and the button is lit blue as long as this button is pressed.
Memory position 2 : The drives move to the saved position. The drives
move and the button is lit blue as long as this button is pressed.
Memory position 3 : The drives move to the saved position. The drives
move and the button is lit blue as long as this button is pressed.
Memory save button: The drives move to their desired positions. Press the
memory save button once: the “Memory position 1-2-3” button light up. Then
press the desired position button within two seconds. The position is saved in
memory.
Battery indicator : If the battery voltage drops below 3.5 V while the
RF-TOUCH is enabled, this button will light up red. This means that the
batteries must be replaced.
Pairing RF-TOUCH
- Connect all components to the drive system.
- Insert the plug into the socket.
- Press the Pairing button (a) 2x until the Pairing-LED (b) turns on. You now have 10s for the pairing process.
- Press and hold the Paring button (P) (located in the battery compartment of the RF-TOUCH).
The pairing LED blinks. This LED stops blinking as soon as the pairing is finished.
Only commission one system at a time. Never configure multiple systems simultaneously.
Adjusting the horizontal position
Move all drives to horizontal position. Press button 4 on the RF-TOUCH and
hold for approx. 3 sec., the memory buttons 1-2-3 will light up blue, then
white, after approx. 3 sec. the background illumination will once flash white,
now the system is ready for saving the new horizontal position, press button 8
within 1 sec. and hold until the background illumination will flash white
twice, then release button 8.
Horizontal position is saved.
Initialization of the RF-Touch
Do not touch the touch surface (surface with the icons) of the RF-TOUCH while
the unit is being commissioned or while the batteries are being changed.
Caution: Do not use in the vicinity of heart pacemakers
23.06.2020
89458 2.0