ZALMAN Z8 MS ATX Mid Tower Computer Case User Manual
- June 4, 2024
- ZALMAN
Table of Contents
Z8 Z8MS Z8 TG
ATX MID-TOWER
COMPUTER CASE
User’s Manual
Ver. 062321
Z8 MS ATX Mid Tower Computer Case
- To ensure safe and easy installation, please read the following precaution.
- Product design and specifications may be revised to improve quality and performance without notice.
Developed and designed by ZALMAN in Korea.
This product is protected by ZALMAN’s pending or registered patents.
Precautions
- Read this manual carefully before installing.
- Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
- Wear gloves to prevent accidents when installing the product.
- Severe damage may occur when mounting the system, so do not apply excessive force.
- Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
- Be careful not to block the ventilation hole of the product when using the system.
- Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
- Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
- Do not insert your hand or another object into the product during operation, as this may injure your hand or damage the object.
- Store and use the product out of children’s reach.
- Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
- The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.
Characteristics
Model | Z8 | I Z8 MS | I Z8 TG |
---|---|---|---|
Case Form Factor | ATX Mid-Tower | ||
Dimensions | 460 x 212 x 493(H)mm | ||
Weight | 6.3kg | I 6.8kg | |
Case Materials | Tempered Glass, Plastic, Steel | ||
Motherboard Support | E-ATX(-280mm) / ATX / mATX / Mini-ITX | ||
Maximum VGA Length | 350mm | ||
Maximum CPU Cooler Height | 160mm | ||
Maximum PSU Length | 180mm | ||
PCI Expansion Slots | 7 | ||
Drive Bays | 2 x Combo (3.5″ or 2.5″, Toolless ), 4 x 2.5″ | ||
Fan Support | Top | 2 x 120mm / 2 x 140mm | |
Front | 3 x 120mm / 3 x 140mm | ||
Rear | 1 x 120mm | ||
Bottom | 2 x 120mm (Remove SSD Brackets) | ||
Fan(s) Included | Front | 3 x 120mm | I Addressable RGB 3 x 120mm |
Rear | 1 x 120mm | ||
I ARGB Controller Included | |||
Radiator Support | Top | 120mm / 240mm / 280mm | |
Front | 120mm | ||
Rear | 120mm | ||
I/O Ports | 2 x USB3.0, 1 x USB2.0, 1 x Headphone Jack, |
1 x Microphone jack, Power Button, Reset Button, LED Button
Accessoires
I/O Ports
# | Part |
---|---|
ⓐ | Power Button |
ⓑ | HDD / Power LED |
ⓒ | Headphone Jack |
ⓓ | Microphone Jack |
ⓔ | USB 2.0 Port |
ⓕ | USB 3.0 Ports |
ⓖ | Reset Button |
ⓗ | LED Button |
Disassembly of the side panels
- Tempered Glass
- Steel Panel
|
---|---
|
5. 2.5” double-sided mounting
6. 3.5” away from two discos in the montage.
※ Z8 MS, Z8 TG Only
LED ARGB 1 ~ 4 / 3 broche
7. Two blocks of elementation in a montage
-
Mounting the top radiator
・120mm ・240mm ・280mm -
Mounting the front and rear radiator
・120mm
9. Ventilateur (s) inclus / Ventilator characteristics
10. Installation country ventilation
-
Mounting the top & bottom fans
・2 x 120mm
・2 x 140mm -
Mounting the front fans
・3 x 120mm
・3 x 140mm -
Mounting the rear fan
・1 x 120mm
11. Connect A/s
www.zalmansvc.com www.zalman.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>