VALBERG 980582-WF Washing Machine Instruction Manual

VALBERG 980582-WF Washing Machine

Product Information

Specifications

• Model: 980582 – WF 1014 A W180C
• Washing/drying Capacity: 10kg
• Max. spin speed: 1400rpm
• Net Weight: 67kg
• Rated Voltage: 220 – 240V~
• Heating Power: 1500W
• Washing Power: 250W
• Dimension:
  • A: 595mm
  • B: 845mm
  • C: 540mm
  • D: 590mm
  • E: 635mm
  • F: 1120mm

Installation

BEFORE USING THE WASHING MACHINE
Removing the packaging and inspection

• After unpacking, ensure that the washing machine is undamaged. If in doubt, do not use the washing machine. Contact After-Sales Service or your local retailer.
• Check that the accessories and supplied parts are all present.
• Keep the packaging materials (plastic bags, polystyrene parts, etc.) out of reach of children, as they are potentially dangerous.

Remove the transport bolts
Important:
Transport bolts which are not removed can cause damage to the appliance.

1. Screw off all transportation bolts for approx. 30mm with wrench following the direction of arrow shown (not fully screw it off).
2. Push four transportation bolts on horizontal direction inward and loose transportation bolt.
3. Pull out transportation bolt together with rubber part and plastic part.
4. To ensure safety and reduce noise, you should install the transportation bolt cover supplied with the unit (see the annex accompanying the unit). Lean and place the transportation bolt into hole and press it following the shown direction until it clicks.

Important: Keep the transport bolts and the wrench for future transporting of the appliance and, in this case, refit the transport bolts in reverse order.
Adjustment of the Feet
The appliance must be installed on a solid and level floor surface. If necessary, use a spirit level to ensure proper leveling. If the appliance is to be installed on a wooden floor, distribute the weight by placing it on a 60x60cm sheet of plywood at least 3cm in thickness and secure it to the floor. If the floor is uneven, adjust the 4 leveling feet as required. Do not insert pieces of wood or other objects under the feet.

1. Slacken the locknut clockwise (see arrow) using the wrench.
2. Lift the machine slightly and adjust the height of the foot by revolving it.

Important: Tighten the locknut by turning it anti-clockwise towards the appliance casing.
Install bottom cover
To realize quieter operation, a bottom cover is supplied with the unit (only applies to some of the Hisense washers). After installing the cover at the bottom of the washer, the noise level will be greatly reduced. Please ask for advice from specialists before installing the cover, nevertheless, the machine can be used without the bottom cover.
Noise-reduction bottom plate installation instructions

1. Before installing the noise-reduction bottom plate, align and paste the acoustic absorption wool with and along the right-angle impression on bottom plate (this procedure is unnecessary for some of the models without acoustic absorption wool).
2. 2. Remove surface paper on double sided tape at four sides of the bottom plate.
3. Incline the machine to an angle of 40° and let the side with right-angle notch face towards front of the washing machine, as shown in the figure. Insert the side with oblique-angle notch between two foot screws at back of the washing machine completely in place. Then, install the bottom plate and ensure that it contacts with bottom of the washing machine closely.
4. Press the double sided tape on four sides manually to secure the noise-reduction palte to the machine body firmly.

Connect the water supply inlet hose

1. If the water inlet hose is not already installed, it must be screwed to the appliance. The blue marked hose is only for cold water.

2. Screw by hand the inlet hose onto the tap, tightening the nut.
   Attention:

   • No kinks in the hose!
   • The appliance must not be connected to the mixing tap of an un-pressurized water heater.
   • Check water-tightness of connections by turning the tap completely on.
   • If the hose is too short, replace it with a suitable length of pressure resistant hose (1000 kPa min).
   • Check the inlet hose regularly for brittleness and cracks and replace if necessary.
   • The washing machine can be connected without a non-return valve.

Connect the drain hose
In case the drain hose is installed as shown below:

1. Unhook it only from the right clip (see arrow)
2. Connect the drain hose to the Drain or hook it over the edge of a sink by means of the “U” bend.
   Fit the “U” bend E, if not already installed, at the end of the drain hose.

Notes:

• Ensure that there are no kinks in the drain hose.
• Secure the hose so that it cannot fall down. After wash phase, machine will drain out hot water.
• Small hand basins are not suitable.
• To make an extension use a hose of the same type and secure the connections with clips.
• Max. Overall drain hose length: 2.50 m.

Before the first wash cycle

To remove any residual water used during testing by the manufacturer, we recommend that you carry out a short wash cycle without laundry.

1. Open the tap.
2. Close the door.
3. Pour a little detergent (about 30 ml) into the main wash chamber of the detergent dispenser.
4. Select and start a short programme.

Preparation of the washing

1. Sort the laundry according to…

2. Type of fabric / care label symbol
   Cottons, mixed fibres, easy care/synthetics, wool, handwash items.

3. Colour
   Separate coloured and white items. Wash new coloured articles separately.

4. Loading
   Wash items of different sizes in the same load to improve washing efficiency and distribution in the drum.

5. Delicates
   Wash small items (e.g. nylon stockings, belts etc.) and items with hooks (e.g. bras) in a cloth bag or pillow case with zip. Always remove curtain rings or wash curtains with the rings inside a cotton bag.

6. Empty all pockets
   Coins, safety pins etc. can damage your laundry as well as the appliance drum and tub.

7. Fasteners
   Close zips and fasten buttons or hooks; loose belts or ribbons should be tied together. Stain removal
   Blood, milk, eggs etc. are generally removed by the automatic enzyme phase of the programme.

   • To remove red wine, coffee, tea, grass and fruit stains etc. add a stain remover to the main wash chamber of the detergent dispenser.

   • Pre-treat heavily-soiled areas with stain remover if necessary.
     Dyeing

   • Only use dyes that are suitable for washing machines.

   • Follow the Manufacturer’s instructions.

   • Plastic and rubber parts of the washing machine can be stained by dyes.

Loading the laundry

1. Open the door.

2. Load the articles one at a time loosely into the drum, without overfilling. Observe the load sizes given in the quick reference guide.
   Note: Overloading the machine will result in unsatisfactory washing results and creased laundry.

3. Close the door.

Detergents and additives

Always use high efficiency, low foam detergent for a front load machine. The choice of detergent depends on:

• type of fabric (cottons, easy care/synthetics, delicate items, wool).
  Note : Use only specific detergents for washing wool.

• colour

• the wash temperature

• degree and type of soiling

Remarks:
Any whitish residues on dark fabrics are caused by insoluble compounds used in modern phosphate-free powder detergents. If this occurs, shake or brush out the fabric or use liquid detergents. Use only detergents and additives specifically produced for domestic washing machines. When using descaling agents, dyes or bleaches for the pre-wash, make sure that they are suitable for use in domestic washing machines. Descalers could contain products which could damage your washing machine. Do not use any solvents (e.g. turpentine, benzine). Do not wash fabrics that have been treated with solvents or flammable liquids.
Dosage
Follow the dosage recommendations on the detergent pack. They depend on:

• degree and type of soiling

• size of wash
  follow the detergent manufacturer’s instructions for a full load;
  half load: 3/4 the amount used for a full load;
  minimum load (about 1 kg): 1/2 the amount used for a full load;

• water hardness in your area (ask for information from your water company). Soft water requires less detergent than hard water.

Notes:
Too much detergent can result in excess foam formation, which reduces washing efficiency. If the washing machine detects too much foam, it may prevent spinning. Insufficient detergent may result in grey laundry in time and also calcifies the heating system, drum and hoses.
Where to put detergent and additives
The detergent drawer has three chambers (fig. “A”)
Prewash chamber

• Detergent for the prewash / soak

Mainwash chamber

• Detergent for the main wash
• Stain remover
• Water softener (water hardness class 4)

Softener chamber

• Fabric softener

Notes:

• Keep detergents and additives in a safe, dry place out of the reach of children.
• Liquid detergents can be used for programmes with prewash. However, in this case a powder detergent must be used for the main wash.
• Do not use liquid detergents when activating the “Delay End” function (if available on your washing machine).
• To prevent dispensing problems when using highly concentrated powder and liquid detergents, use the special detergent ball or bag supplied with the detergent and place it directly inside the drum.
• When using descaling agents, bleaches or dyes, make sure that they are suitable for washing machines. Descalers could contain compounds that can damage parts of your washing machine.
• Do not use any solvents in the washing machine (e.g. turpentine, benzine).

Operation

This washing machine is equipped with automatic safety functions which detect and diagnose at an early stage and react appropriately.
Control Panel

1. “Temp.” button
2. Child Lock Function
3. “Spin” button
4. Mute Function
5. “Steam” button
6. “Option” button
7. “Delay End” button
8. “Start/Pause” button
9. “Power” button
10. Program selector
11. Program and function status display window

Programmes

1. Wash performance test program are: Eco 40-60.
2. Allergy Steam and Baby Steam Care both washing are suitable to sterilize the colorfast clothes. When you see the door glass with water mist, please don’t put your hand on the door glass or open the dispenser to prevent burns.

Add Detergent, Close the Door and Set the Program
Load the clothes to be washed in the drum and close the door. Add the detergent into the relevant compartments for the type of program you are going to select, Add detergent as described in Detergent and Additives section.

1. Turn on the power.
2. Spin program selection knob to required program
3. Select washing temperature, spin speed by pressing “Temp”, “Spin” buttons.
4. Press “Option” button to select additional functions.
5. After starting the program, display window displays program length (hours: minutes) and additional function options in sequence.

Program| Washing temperature select| Laundry and textile| Recommended detergent
---|---|---|---
Wool| –, 20, 40°C| Wool fabric| Mild detergent
20°C| 20°C| Synthetic materials, coloured laundry made from easy care fibres| Colour or mild detergent without optical brighteners
Cotton, Eco 40-60, Dark Wash, Sports, Synth, Mix, Quick 15’| –, 20, 40, 60°C| Synthctic materials, coloured laundry made from cotton or linen| Colour detergent free of bleach and optical brighteners
Cotton, Eco 40-60, Dark Wash, Baby care, Allergy| 40, 60, 95°C| White laundry made from boil-proof cotton or linen| Strong detergent containing bleach and optical brighteners

Addition function selection
At standby state, press “Option” button to select additional function for current program. Select only one function for each press, and then corresponding icon flashes. After starting up, program cannot be changed.
Pre-wash

• Select the function to conduct pre-wash so as to enhance washing effects and better remove stains. This function is suitable for heavy dirt clothes.
• Before inflowing, laundry detergent/ washing powder can be added to pre-wash box, and washing powder must be added to main wash box.

Extra Rinse
After set the function of rinsing adding, the program runs the rinsing process once again before running the softening, and the total running time of the program increases accordingly.
Intensive
The function can be selected to prolong washing time, strengthen washing effects and better remove stain.
Inlet water warning
If tap is not opened, or water pressure is over low, display screen will prompt “F01” to give alarm.
Drainage warning
If the pipe is squeezed, drainage will not be smooth. In case of failing to completely drain for long time, display screen will prompt “F03” to give alarm.
Door Lock Icon
After the program starts the Door Lock icon will light up and the door will be locked.

• After completing program, door lock unlocks automatically. When the washing machine is paused, if the door lock opening conditions are met, the door lock will open.
• When door lock indicator light flashes, door shall not be opened forcibly so as to avoid personal injury.

Delay End Function
Delay end function allows to run the machine at the consumers’ convenience, for example, at night when electricity is cheaper.

• Only under the standby mode, this button is valid for selecting the reservation time.
• After the reservation function is selected, the time will increase 1h when each time the reservation button is pressed. Before reservation, if the program time does not satisfy the integral multiple of 1h, it shall be completed by pressing the reservation key for the first time, and then the time increases 1h when each time the reservation button is pressed. If the reservation is selected, before the program runs, the current reservation can be canceled by turning the button to select other programs.
• The delay time must be longer than the wash program length as the delay time is the time program will finish. For example: if the selected program time is 02:28, the delay time selected must be between 03:00 and 24:00.
• When the reservation process is operated, the icon of “reservation time” will be on. When the reservation process is finished, the icon of “reservation time” will be off.

Steam
Press briefly, add steam function, and the steam icon will light up.
Press twice to cancel the function, and cycle in sequence.

Mute Function
When the machine is in the state of holding, pause or operation, press “Spin + Steam” buttons for 2 seconds. All the buzzing will be turned off except the alarms.
When the machine is in the mute state, press “Spin + Steam” buttons for 2 seconds. All the buzzing will be activated.

Automatic weighting
Washing machine displays “—-” after startup, indicating that it is weighing automatically. It will adjust program length (hours: minutes) automatically according to weight of clothes.

Child Lock
To strengthen the safety of children, this machine is equipped with Child Lock function. When the programme starts, press “Temp. + Spin” button for 2 seconds. Child Lock icon will light up, and then Child Lock is set up. Repeat the same operation, the Child Lock will be released.

• When the Child Lock is set, all function buttons will be shielded.
• When you turn off the machine, child lock is released.
• After completing program, child lock will automatically unlock.

To Start the Program
After you have selected your options and placed detergent with in the detergent dispenser, turn on the water tap and press the “   ” button. The screen will display the current program progression. It also displays the remaining program time.

To Cancel the Program or Reselect the Options

1. Press the “   ” button for 3 seconds to turn off the machine.
2. Select the new program and options.
3. Press “  ” button to turn on the machine without adding any extra detergent.

End of the Program
The washing machine shows “END” at the end of the program, when the door is unlocked. Press the “   ” button, the power will be cut off. If there is no button or knob operation within 2 minutes, the program will automatically power off.

Reload in Process
If you want to reload clothes in the process of washing, please press “   ” button.

• If reload icon light up, the door can be opened in the process, remaining time and the Door Lock icon in display will flash. Then the Door Lock icon will go out, and the door can be opened.
• If reload icon doesn’t light up, the Door Lock icon doesn’t flash, it indicates that current temperature is over 50°C or you have passed the time for reloading in the process, namely no clothes allowed to load into the machine.

Programme Instructions

1. The eco 40-60 programme is able to clean normally soiled cotton laundry declared to be washable about 40°C to 60°C, together in the same cycle, and that this programme is used to assess the compliance with the EU eco design legislation.
2. The power consumption of the off-mode is 0.49W.
3. The most efficient programmes in terms of energy consumption are generally those that perform at lower temperatures and longer duration.
4. Loading the household washing machine up to the capacity indicated by the manufacturer for the respective programmes will contribute to energy and water savings.
5. Correct use of detergent, softeners and other additives. Do not apply excessive detergent. This may affect the washing results adversely.
6. Periodic cleaning, including optimal frequency, and limescale prevention and procedure.
7. Noise and remaining moisture content are influenced by the spinning speed: the higher the spinning speed in the spinning phase, the higher the noise and the lower the remaining moisture content.
8. The product information and QR code are reflected in the energy consumption label, the product registration information can be obtained by scanning the QR code.
9. The information of standard programmes.

Program| Selected Temperature (°C)| Rated Capacity (kg)| Maximum temperature in drum

(°C)

| Program duration (h:min)| Energy consumption (kWh/cycle)| Water consumption (litres/ cycle)| Remaining moisture content (%)| Maximum speed reached (rpm)
---|---|---|---|---|---|---|---|---
Eco 40-60 full load| –| 10| 40| 3:59| 1.020| 55.0| 51.00| 1400
Eco 40-60 half load| –| 5| 28| 3:00| 0.430| 40.0| 53.00| 1400
Eco 40-60 1/4 load| –| 2.5| 24| 3:00| 0.220| 30.0| 53.50| 1400
20’C| 20| 10| 20| 1:50| 0.200| 85.0| 51.00| 1400
Cotton| 60| 10| 55| 3:29| 1.560| 108.0| 53.00| 1400
MIX| 40| 5| 45| 1:00| 0.850| 69.0| 45.00| 1400
Quick 15′| 40| 1| 38| 0:30| 0.330| 22.0| 55.00| 800

The values given for programmes other than the eco 40-60 programme are indicative only.

Emergency door opening
In case of failure to open the door due to power outage or other special circumstances, the door lock lever at the drainage pump door can be used for emergency opening.

Notes:

• Do not operate when the machine is working normally;
• Before operation, please make sure that the inner barrel has stopped turning, without high temperature, and the water level is lower than the clothing inlet. If the water level is higher than the clothing inlet, drain off water through the drain-away pipe (if available) or by slowly unscrewing the filter.
• Operation method: Open the cover of drainage pump door, pull down the lock lever with the help of a tool, and then the door can be opened(indicated in the figure).

Cleaning and Maintenance

For cleaning and maintenance instructions, please refer to the user manual provided with the product.

Appliance exterior and control panel

• Can be washed down with a soft, damp cloth.
• A little neutral detergent (non abrasive) can also be used.
• Dry with a soft cloth.

Door seal

• Clean with a damp cloth when necessary.
• Check the condition of the door seal periodically.

Detergent dispenser

1. Press the release lever in the main wash compartment downward and remove the drawer.
2. Remove siphon in softener slot.
3. Wash all the parts under running water.
4. Refit the siphon in the detergent drawer and fit the drawer back inside its housing.

Filter
We recommend that you check and clean the filter regularly, at least two or three times a year.

Especially:

• If the appliance is not draining properly or if it fails to perform spin cycles.
• If the pump is blocked by a foreign body (e.g. buttons, coins or safety pins).

IMPORTANT: Ensure that the water has cooled before draining the appliance.

1. Stop the appliance and unplug it.
2. Insert removal tool like slotted screwdriver into the small opening of bottom baffle, press the bottom baffle downward with much strength and open it.
3. Put a flat container under filter door and then drain with emergency drain pipe (see [draining residual water] for specific operation methods). Then, loosen filter anticlockwise and completely unscrew and remove the filter.
4. Clean the filter and the filter chamber.
5. Check that the pump rotor moves freely.
6. Re-insert the filter and screw it in clockwise as far as it will go.
7. Reinstall the plinth.

Water supply hose
Check the supply hose regularly for brittleness and cracks and replace it if necessary using a new hose of the same type (available from After-Sales Service or specialist dealer).

Mesh filter for water connection
Check and clean regularly.
For washing machines with an inlet hose as shown on pictures “D”,

1. Close the tap and loosen the inlet hose on the tap.
2. Clean the internal mesh filter and screw the water inlet hose back onto the tap.
3. Now unscrew the inlet hose on the rear of the washing machine.
4. Pull off the mesh filter from the washing machine connection with universal pliers and clean it.
5. Refit the mesh filter and screw the inlet hose on again.
6. Turn on the tap and ensure that the connections are completely water-tight.

Troubleshooting guide

Depending on the model, your washing machine is equipped with various automatic safety functions. This enables faults to be detected in good time and the safety system can then react appropriately. These faults are frequently so minor that they can be resolved within a few minutes.

• the mains plug is inserted into the socket
• the wall socket is functioning correctly (use a table lamp or similar appliance to test it).

The washing machine will not start… and the “Start/ Pause” indicator lamp flashes.|

• the door is properly closed (child safety);
• the “ Start/Pause ” button has been pressed;
• the “Water tap closed” indication lights up. Open the water tap and press the “ Start/Pause ” button.

The appliance stops during the programme (varies depending on model).|

• the door has been opened and the “ Start/Pause ” indicator lamp is flashing. Close the door and press the “Start/Pause” button again.
• Check if there is too much foam inside, machine enters kill-foam routine. The machine will run again automatically after a period.
• the washing machine’s safety system has been activated (see “Fault description table”).

Residue from detergent and additives left in the detergent drawer at end of wash.|

• the cover grid of the softener chamber and the separator of the main wash chamber are correctly installed in the detergent dispenser and all parts are clean (see “Care and maintenance”);
• sufficient water is entering. The mesh filters of the water supply could be blocked (see “Care and maintenance”);
• the position of the separator in the main wash chamber is adapted to the use of powder or liquid detergent (see “Detergent and additives”).

Machine vibrates during spin cycle.|

• the washing machine is level and standing firmly on all four feet;
• the transport bolts have been removed. Before using the machine, it is imperative that the transport bolts are removed.

Final spin results are poor.| The washing machine has an imbalance detection and correction system. If individual heavy items are loaded (e.g. bathrobes), this system may reduce the spin speed automatically or even interrupt the spin completely if it detects too great an imbalance even after several spin starts, in order to protect the washing machine.

• If the laundry is still too wet at the end of the cycle, remove some articles of laundry and repeat the spin cycle.
• Excessive foam formation may prevent spinning. Use the correct amount of detergent.
• Check that the spin speed selector has not been set to “0”.

---|---
If your washing machine has a time display: the programme time initially displayed is lengthened / shortened by a period of time:| This is a normal capacity of the washing machine to adapt to factors that can have an effect on the wash programme time, e.g.:

• excess foam formation;
• load imbalance due to heavy items of laundry;
• prolonged heating time due to reduced inlet water temperature;

Because of influences like these, the time remaining in the programme run is recalculated, and updated if necessary. In addition, during the filling phase, the washing machine determines the load and if necessary adjusts the initial programme time displayed accordingly. During such update periods, an animation appears on the time display.

Enter the after-sales query mode

1. In the OFF mode, press the “ to enter the after-sales inquiry mode.
2. It displays the number of operation cycles.
3. Press “ ” to switch cycles or fault codes
4. When querying fault codes, press the “ ” to page up and the “ ” to page down.

For Models with Single Inlet
Fix the inlet hose to the cold water tap and to the inlet valve on the rear side of the machine as .

Ensure that:
All connections are tightly fixed.

WARNING!

• Do not allow children to operate, crawl on, be near or inside your washer.
• Note that during the wash cycles, the surface temperature of the porthole door may increase.
• Close supervision of children is necessary when the appliance is used near children.

Fault Code List

“F01” displayed on screen
The machine is not fed with water or insufficient water.

Check:

• Faucet is fully open and has enough water pressure.
• Water inlet pipe is knotted or not.
• Filtering net of water inlet pipe is blocked or not (refer to maintenance and repair).
• Water pipe is frozen or not.
  Press “Start/Pause” key after fault is removed. If fault occurs again, please contact with after-sale service (refer to after-sale service.).

“F03” displayed on screen
The washer is not emptied. The washer stops the program being executed. Shut down the machine and disconnect power supply.

Check:

• Drain pipe is knotted or not.
• Filter in drain pump is blocked or not (refer to the cleaning of filter in drain pump)

IMPORTANT: Ensure that the water has cooled before draining the appliance.

• the drain hose is frozen up.
  Plug in the appliance again. Select and start the “Spin” programme or push the “Start/Pause” button for at least 3 seconds and restart the desired programme. If the fault occurs again, please contact After-Sales Service (see “After- Sales Service”).

Fault code
The washer stops when the program is running. The display window shows fault code “F13”, “F14”, “F24”, else fault codes from “F04” to “F98” or “Unb”.

If fault code “F13” is shown
Door lock is abnormal. Start program for 20 sec and unlock the washer door (PTC) to check whether the door is closed. Open or close it again.  After fault is removed, press “Start/Pause” key. If fault occurs again, disconnect power supply and contact with after-sale service.

If fault code “F14” is shown
Door open fault.
Action: Press “Start/Pause” button. The washing machine will try to open the door.
The alarm will not be removed until the door is unlocked. Or turn the nub to off for 3 seconds to turn off the machine. Choose the desired programmme to start the machine. The alarm will be removed.

If fault code “F24” is shown
Water level reaches overflow level. Remove it by pressing “Start/Pause” key and feed water. Select and start required program. If fault occurs again, disconnect power supply and contact with after-sale service.

If else fault code “F04” to “F98” is shown
Electronic module fails.
Turn the nub to Off for 3 seconds to turn off the machine. After fault is removed, press “Start/Pause” key. If fault occurs again, disconnect power supply and contact with after-sale service.

If fault code “Unb” is shown
Unbalance alarm shall be solved by the following methods.

1. Laundry winding
   Turn the knob to “off” for 3 seconds for shutdown, open the door, shake the clothes and put them back into the washing machine, then select the single dewatering program to dry again.

2. Too light-weighted laundry
   Turn the knob to “off” for 3 seconds for shutdown, open the door, put in one or two towels, and then select the single dewatering program to dry again.

Before contacting After-Sales Service:

1. Try to remedy the problem yourself (see “Troubleshooting Guide”).
2. Restart the programme to check whether the problem has solved itself.
3. If the washing machine continues to function incorrectly, call After-Sales Service.

Transport/handing
Never lift the appliance by the worktop when transporting.

1. Pull out the mains plug.
2. Turn off the tap.
3. Disconnect the inlet and drain hoses.
4. Eliminate all water from the hoses and from the appliance (see “Removing the Filter”, “Draining Residual Water”).
5. Fit the transport bolts (obligatory).
6. The machine is over 55 kg in weight, two persons are needed to move it.

FAQ (Frequently Asked Questions)

What should I do if the washing machine is not starting?
Please ensure that the power cord is properly plugged in and that there is power supply to the machine. Also, make sure that the door is properly closed.

How much detergent should I use for each wash?
The recommended amount of detergent depends on the load size and the detergent brand. Please refer to the detergent packaging for dosage instructions.

Can I wash wool in this washing machine?
Yes, you can wash wool in this washing machine. Follow the instructions provided in the user manual for washing wool garments.

Product overview

Parts

• A Worktop
• B Control panel
• C Detergent dispenser
• D Door
• E Plinth covering pump access
• F Adjustable feet

Parts supplied

• Package with small items
• Instruction for use, installation guide, warranty card (depends on model)
• 4 plastic caps
• Wrench
• Inlet hose (inside the machine or already installed)
  • Cold inlet hose
  • Hot inlet hose (if available, depending on models)
• “U”-bend (inside the machine or already installed)
• Bottom cover (depends on model)

WARRANTY CONDITIONS
This product is guaranteed against faults caused by defects in manufacturing or the materials used for a period of two years, starting from the date of purchase.* This warranty does not cover defects or damage caused by failure to install the device correctly, incorrect use of the product, or excessive wear and tear.

• proof of purchase required.

ELECTRO DEPOT
1 route de Vendeville
59155 FACHES-THUMESNIL – FRANCE

References

• valberg.de is available for purchase - Sedo.com
• Tienda de electrodomésticos y electrónica | ELECTRO DEPOT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>