AOSTIRMOTOR S18 750W 26 Inch Fat Tire Electric Bikes for Adults E-Bike User Manual

User Manual
S18
750W 26 Inch Fat Tire Electric Bikes for Adults E-Bike

Product Description

Safety Notice

To Ensure Your Safety, Make the Following Functional Checks Before Driving:

1. Test brake system, throttle, and power system.
2. Tire pressure should be at 30 psi.
3. Check front wheel lug-nuts, securely tighten before every ride.
4. Battery charge level- found on side of battery
5. Braking system adjustment and free operation.

Installation Instruction

1. Open your package.

2. Take out the tool box.

3. Take out the bicycle from the package and put it on a soft surface to avoid scratches.
   Cut the tie that secures the front wheel to the side

4. Remove the protective foam.

5. Open the accessory kit and remove the tool kit

6. Invert the bicycle.

7. Remove the large fixing bolt on the front fork.

8. Put the front wheel on the front fork and place the disc brake pad on the front wheel in the middle of the disc brake caliper( Figure 1)

9. Use the supplied 15mm fla tool to tighten the two bolts.

10. Tie the key 1o the handiebar clamp, cut the zipper, and then use the Allen wrench in the t00l kit to remove the clamp.

11. Place the handiebar in the middle position (Figure 2), nstall the rod clamp and tighten the screws with the included Allen wrench.

12. Install the LCD-display on the handlebar (Figure 3), tighten the screws, and connect the green connecting wire (Figure 4)

13. Grasp the bicycle light and unscrew the lens. Then, remove the plastic insulator, re-tighten the lens, and then connect the red cable (Figure 5), and connect the bicycle light t0 the screw above the front fork (Figure 6).

14. Install the pedal. The right pedal rotates clockwise (Figure 7), and the left pedal rotates counterclockwise (Figure 8 NOTE:Pedal mark “L” means left and anoms “R” means right.

15. Vertical bicycle

16. Push the seat into the column, fix it i the desired position, tighten the screws, and then fxit.

17. Installation is complete.\When connecting meters, headights, brake circuit breakers, handiebars, etc., please align them and do not install violently(Figure 4).

Battery Installation & Maintenance

1. Please check the situation of the lock core before installation, Step 2 and Step 3 for details.

2. Tur your key counterclockvise to make the lock cylinder downward.

3. As shown in the left picture, align the sider

4. There are two lock positions, the locking principle is the same, ‘and the other lock position can also control the switch of the battery.
   The No. 3 port s the charging port

5. Tum It clockwise to lock your battery.

6. Press down the key and tu it counterclockwise to unlock your battery.

7. When not using the battery for a long time, please charge it 1-2 times every month.

8. Please keep the key properly. If your key is lost, we can provide a new key according to the nameplate number on the key

9. Please keep the battery environment dry, for example, do not stay in the rain for a long time

10. Please use a universal meter o test the battery attenuation regularly

Display Use & Maintenance

SW-LCD display
OPENModeM 1.5 seconds ong press.
CLOSE:In standby mode, long press Mode/M for 3 seconds.
‘SETTING. After booting, press UP+DOWN for 2.5 seconds(exit In the same way)
The detailed settings are as ollows:(on the boo state) Wheel Diameter Setting:

1. UP or DOWN
2. 16.28inch(defaul 28inch)
3. Select, Mode Confirm

Speed Setting

1. UP o DOWN
2. 12-45 KMIH
3. Select, Mode Confirn

Light Setting

1. UP or DOWN
2. 1-3 (Brightness)
3. Select, Mode Confirm

MPHKM Satiing:

1. Up or OWN
2. MPH or KNH
3. Select, Mode Confirm

SPEED Setting:

1. UP of DOWN For 3 seconds
2. MAXIAVGINOW
3. Select, Mods Confirm

RANGE Setting:

1. PRESS Mode/M
2. Riding mileage /Accumulat-ed total mileage

Front Light Open:

1. Exit Settings
2. UP FOR 3 Seconds
3. Frontlamp will work.
4. Defaut:

Power Shift Seting

1. Exit Setings
2. UPIDOWN
3. 1-5 (Powen)
4. Defaut

Cruise Mode Seting.

1. Exit Settings
2. PRESS DOWN FOR 3 Sec-onds
3. Defaut: SKMIH
4. Pushing state, non riding

Controller Use & Maintenance

1. Batery negative connection ine

2. Batery positive connection ine

3. Phase line

4. Tail lignt wire

5. Integrated main line

6. Power sensor line

7. Motor Hall plug wire

8. Please be careful not to get water into the controller box

9. When the bike does not work: 1)Check the connection of controller cables;

2. Try to restart or Replace the controler; 3)Contact us with email

Motor Maintenance

1. Please check the integrity of motor blocking piece regularly.
2. Please check the integrity of cable before and after riding.
3.  Please check the integrity of motor shell before and after riding.
4. Please do not use the motor in exireme environments, and do not let the motor work in water.
5. When you find the motor power is insuffiient, please get out of the bike and not force it.

FAQ

« Is there a power usage or battery gauge on the bike?

Yes, there is a full screen LCD display. There s also an additional LED battery gauge on the side of the battery pack. 2x the infol

« Is there a switch to prevent accidental starting?

Yes, there is an on/off button on the battery pack. The brake levers also come standard with a safety power stop switch bult in

• How do I lock it up and what can | do to help minimize the chance of it being stolen?

AOSTIRMOTOR Bike has some great anti-theft features, including a locking battery rack with keys to keep bike safe, and rear wheel which is bolted down reduce the chances to be stolen.

Dose itwork in the rain?

The components are all waterproof and work very well in wet conditions, But we do not suggest 1o use our ebike in a rain day. We suggest that you should keep your bike parked indoors and keep him in a dry situa- tion,

POWER BRINGS JOY
www.AOSTIRMOTOR.com
aostirmotor@gmail.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>