AOSTIRMOTOR S07-F 750W Electric Bike Instruction Manual
- October 30, 2023
- AOSTIRMOTOR
Table of Contents
AOSTIRMOTOR S07-F 750W Electric Bike
Display Use & Maintenance
SW-LCD display
OPEN: Mode/M 1.5 seconds long press.
CLOSE: ln standby mode, long press Mode/M for 3 seconds
SETTING: After booting, press UP+DOWN for 2.5 seconds(exit in the same
way) The detailed settings are as follows:(on the boot state)
Wheel Diameter Setting
- UP or DOWN
- 16-28inch C Default 26inch )
- Select, Mode Confirm
Speed Setting
- UP or DOWN
- 12-45 KM/H
- Select, Mode Confirm
Light Setting
- UP or DOWN
- 1-3 (Brightness)
- Select, Mode Confirm
MPH/KM Setting
- UP or DOWN
- MPH or KM/H
- Select, Mode Confirm
SPEED Setting
- UP or DOWN For 3 seconds
- MAX/AVG/NOW
- Select, Mode Confirm
RANGE Setting
- PRESS Mode/M
- Riding mileage/ accumulated total mileage
Front Light Open
- Exit Settings
- UP FOR 3 Seconds
- The front lamp will work
- Default: 1
Power Shift Setting
- Exit Settings
- UP/DOWN
- 1-5 (Power)
- Default: 1
Cruise Mode Setting
- Exit Settings
- PRESS DOWN FOR 3 Seconds
- Default: 6KM/H
- Pushing state, nonriding
- Ride your bike in a safe way. Don’t hit or knock the display.
- Keep away from bad environments when use, such as downpours, large snowflakes, and solarization.
- Try not to use it in under-voltage conditions.
- The screen will get dark along with the temperature reduction when the temperature is below-10°C. The screen will return to normal when the temperature rises again.
Controller Use & Maintenance
-
Battery negative connection line
-
Battery-positive connection line
-
Phase line – ERROR 23
-
Tail light wire
-
Integrated main line
-
Power sensor line
-
Motor Hall plug wire
-
Please be careful not to get water into the controller box
-
When the bike does not work: 1 )Check the connection of controller cables;
-
Try to restart or Replace the controller; 3)Contact us by email
Motor Maintenance
- Please check the integrity of the motor blocking piece regularly.
- Please check the integrity of the cable before and after riding.
- Please check the integrity of the motor shell before and after riding.
- Please do not use the motor in extreme environments, and do not let the motor work in water.
- When you find the motor power is insufficient, please get out of the bike and not force it.
FAQ
-
Is there a power usage or battery gauge on the bike?
Yes, there is a full-screen LCD display. There is also an additional LED battery gauge on the side of the battery pack. 2x the info! -
Is there a switch to prevent accidental starting?
Yes, there is an on/off button on the battery pack. The brake levers also come standard with a safety power stop switch built in. -
How do I lock it up and what can I do to help minimize the chance of it being stolen?
AOSTIRMOTOR Bike has some great anti-theft features, including a locking battery rack with keys to keep the bike safe, and a rear wheel that is bolted down to reduce the chances to be stolen.
Most standard U-locks and cable locks work fine on our AOSTIRMOTOR Ebike. -
Does it work in the rain?
The components are all waterproof and work very well in wet conditions,
But we do not suggest using our bikes on a rainy day.
We suggest that you should keep your bike parked indoors and keep him in a dry situation.
Product Description
Safety Notice
To Ensure Your Safety, Make the Following Functional Checks Before Driving:
- Test brake system, throttle, and power system.
- Tire pressure should be at 30 psi.
- Check the front wheel lug nuts, and securely tighten them before every ride.
- Battery charge level- found on the side of the battery.
- Braking system adjustment and free operation.
Installation Instructions
- Open your package.
- Take out the toolbox.
- Take out the bicycle from the package and put it on a soft surface to avoid scratches. Cut the tie that secures the front wheel to the side
- Remove the protective foam.
- Open the accessory kit and remove the tool kit
- Invert the bicycle.
- Remove the large fixing bolt on the front fork.
- Put the front wheel on the front fork and place the disc brake pad on the front wheel in the middle of the disc brake caliper( Figure 1 ).
- Use the supplied 15mm flat tool to tighten the two bolts.
- Tie the key to the handlebar clamp, cut the zipper, and then use the Allen wrench in the tool kit to remove the clamp.
- Place the handlebar in the middle position (Figure 2), install the rod clamp, and tighten the screws with the included Allen wrench.
- install the LCD display on the handlebar (Figure 3), tighten the screws, and connect the green connecting wire (Figure 4)
- Grasp the bicycle light and unscrew the lens. Then, remove the plastic insulator, re-tighten the lens, and then connect the red cable (Figure 5), and connect the bicycle light to the screw above the front fork (Figure 6).
- install the pedal. The right pedal rotates clockwise (Figure 7), and the left pedal rotates counterclockwise (Figure 8).NOTE: Pedal mark “L” means left and “R” means right.
- Vertical bicycle
- Push the seat into the column, fix it in the desired position, tighten the screws, and then fix it.
- Installation is complete. When connecting meters, headlights, brake circuit breakers, handlebars, etc., please align them and do not install them violently(Figure 4).
Battery Installation & Maintenance
-
Please check the situation of the lock core before installation, Step 2 and Step 3 for details.
-
Turn your key counterclockwise to make the lock cylinder downward.
-
As shown in the left picture, align the slider.
-
install along the buckle.
-
Battery installation complete.
-
Turn on the switch and the battery is powered.
-
When not using the battery for a long time, please charge it 1-2 times every month.
-
Please keep the key properly. If your key is lost, we can provide a new key according to the nameplate number on the key.
-
Please keep the battery environment dry, for example, do not stay in the rain for a long time.
-
Please use a universal meter to test the battery attenuation regularly.
POWER BRINGS JOY
www.AOSTIRMOTOR.com.
aostirmotor@gmail.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>