AOSTIRMOTOR GM-LH-155 26 Inch Tire 350 Watt Electric Bike Installation Guide
- October 30, 2023
- AOSTIRMOTOR
Table of Contents
GM-LH-155 26 Inch Tire 350 Watt Electric Bike
Installation Guide
Product Descriptions
Frame | 6061 aluminum alloy | Battery | 36V 10Ah lithium battery |
---|---|---|---|
Motor | 350W Rear brushless hub motor | Controller | 36V 15A |
Charge Time | 4-6 hours | Max Speed | 35-40 km/h |
Range Distance | 25-35 km | Brake | F/R disc brake |
Light | F: Light | Display | M5 LCD display |
Fork | Al alloy suspension fork | Tire | 26×2.1 |
Derailleur | Outer 7 speed SHIMANO | Packing Size | 138″26″65cm |
Safety Notice
To Ensure Your Safety, Make the Following Functional Checks Before Driving:
- Test brake system, throttle, and power system.
- Tire pressure should be at 30 psi.
- Check front wheel lug-nuts, securely tighten before every ride.
- Battery charge level- found on side of battery.
- Braking system adjustment and free operation.
- Open your package.
- Take out the tool box.
- Take out the bicycle from the package and put it on a soft surface to avoid scratches. Cut the tie that secures the front wheel to the side
- Remove the protective foam.
- Open the accessory kit and remove the tool kit
- Invert the bicycle.
- Remove the large fixing bolt on the front fork.
- Put the front wheel on the front fork and place the disc brake pad on the front wheel in the middle of the disc brake caliper( Figure 1).
- Use the supplied 15mm flat tool to tighten the two bolts.
- Tie the key to the handlebar clamp, cut the zipper, and then use the Allen wrench in the tool kit to remove the clamp.
- Place the handlebar in the middle position (Figure 2), install the rod clamp and tighten the screws with the included Allen wrench.
- Install the LCD-display on the handlebar (Figure 3), tighten the screws, and connect the green connecting wire (Figure 4)
- Grasp the bicycle light and unscrew the lens. Then, remove the plastic insulator, re-tighten the lens, and then connect the red cable (Figure 5), and connect the bicycle light to the screw above the front fork (Figure 6).
- Install the pedal. The right pedal rotates clockwise (Figure 7), and the left pedal rotates counterclockwise (Figure 8). NOTE: Pedal mark “L” means left and “R” means right.
- Vertical bicycle
- Push the seat into the column, fix it in the desired position, tighten the screws, and then fix it.
- Installation is complete. When connecting meters, headlights, brake circuit breakers, handlebars, etc., please align them and do not install violently(Figure 4).
Battery Installation & Maintenance
-
Please check the situation of the lock core before installation, Step 2 and Step 3 for details.
-
Turn your key counterclockwise to make the lock cylinder downward.
-
As shown in the left picture, align the slider
-
As shown in the left picture, align the slider
-
Check that the battery is securely installed
-
finish installation
-
When not using the battery for a long time, please charge it 1-2 times every month.
-
Please keep the key properly. If your key is lost, we can provide a new key according to the nameplate number on the key
-
Please keep the battery environment dry, for example, do not stay in the rain for a long time
-
Please use a universal meter to test the battery attenuation regularly
Display Use & Maintenance
M5 LCD display
Functions
a. Display Speed Display, PAS Level Display, Battery Level Display, Error
Indication, Total Mileage, Single Mileage, Single Running Time Light Signal
b. Control and Settings Power Switch, Front Light Control, 6km/h Inching
Control, Wheel Diameter Setting, Top Speed Setting, Auto-Hibernation Interval,
Backlight Brightness Setting, Voltage Level Setting
c. Communications Protocol: UART Display Readings (display at start for 1
second)
Multi-Functions Display
Total Mileage: ODO Single Mileage: TRIP A Single Mileage: TRIP B Current
Voltage VOL Operating Current: CUR Display Booting Time: TM
Riding Mode
Walk: Walking Boost Cruise: Constant Speed Cruise PAS: Power Assist Level (0-9
Adjustable)
Speed Display
Maximum Speed: MAX Average Speed: AVG Measuring Unit: MPH or KM/H The display
will calculate the actual travelling speed based on the wheel diameter and
signal data.
Vehicle Status
Error Code and Indications
Error Code (decimal) | Indica tr3n s | Note |
---|---|---|
0 | Normal | |
1 | Reserved | |
2 | Brake | |
3 | PAS Sensor Failure (riding mark) | Not Realized |
4 | 6km/h Cruise | |
5 | Real-lime Cruise | |
6 | Low Battery | |
7 | Motor Failure | |
8 | Throttle Failure | |
9 | Controller Failure | |
10 | Communications Receiving Failure | |
11 | Communications Sending Failure | |
12 | BMS Communications Failure | |
13 | Light Failure |
Settings
P01: Backlight Brightness (1: darkest; 3: brightest)
P02: Mileage Unit (0: KM; 1: MILE)
P03: Voltage Class: 24V / 36V (default) / 48V
PO4: Hibernation Time (0: never, other figures refer to the hibernation time)
Unit: minute
P05: PAS Level — 0/3 Gear Mode 1/5 Gear Mode
P06: Wheel Diameter Unit: inch Precision: 0.1
- To get accurate speed display, this parameter should be correct.
P07: Magnet Steel Number for Speed Test Range: 1-100 - To get accurate speed display, this parameter should be correct.
Gearless Motor: the value is the magnet steel number.
Geared Motor: the reduction-gear ratio is required. The value = magnet steel number reduction-gear ratio.
P08: Speed Limit
Range: 0-100km/h, parameter 100 indicates no speed limit.
This parameter limits the max. speed of the vehicle.
Deviation: ±1 km/h (applies to both PAS and throttle mode).
Note: The above-mentioned values are measured by metric unit (kilometers). When the measuring unit is switched to imperial unit (mile), the speed value displayed on the panel will be automatically switched to corresponding imperial unit, however the speed limit value in the imperial unit interface won’t change accordingly.
IMPORTANT: P09-P15 only works under communications mode.
P09: Zero / Non-zero Start Setting: 0: Zero Start1: Non-zero Start
P10: Drive Mode Setting
0: Power Drive — The specific gear of the assist drive decides the assist power value. In this status the handlebar does not work.
1: Electric Drive — The vehicle is driven by the handlebar. In this status the power gear does not work.
2: Power Drive + Electric Drive — Electric drive does not work in zero-start status.
P11: PAS Sensibility Range: 1-24
P12: Assist Power Intensity Range: 0-5
P13: Power Magnet Steel Number: 5 / 8 / 12pcs
P14: Current Limit Value: 12A by default; Range: 1-20A
P15: Unspecified
P16: ODO Zero-Out: Long press the upper key for 5 seconds and ODO will zero out.
Motor Maintenance
- Please check the integrity of motor blocking piece regularly.
- Please check the integrity of cable before and after riding.
- Please check the integrity of motor shell before and after riding.
- Please do not use the motor in extreme environments, and do not let the motor work in water.
- When you find the motor power is insufficient, please get out of the bike and not force it.
FAQ
Is there a power usage or battery gauge on the bike?
Yes, there is a full screen LCD display. There is also an additional LED battery gauge on the side of the battery pack. 2x the info!
Is there a switch to prevent accidental starting?
Yes, there is an on/off button on the battery pack. The brake levers also come standard with a safety power stop switch built in.
How do I lock it up and what can I do to help minimize the chance of it being stolen?
AOSTIRMOTOR Bike has some great anti-theft features, including a locking battery rack with keys to keep bike safe, and rear wheel which is bolted down reduce the chances to be stolen. Most standard U-locks and cable locks work fine on our AOSTIRMOTOR Ebike.
Does it work in the rain?
The components are all waterproof and work very well in wet conditions, But we do not suggest to use our ebike in a rain day. We suggest that you should keep your bike parked indoors and keep him in a dry situa-tion.
POWER BRINGS JOY
Www.AOSTIRMOTOR.com
aostirmotor@gmail.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>