AOSTIRMOTOR S07-B Affordable 750W Electric Bike User Manual
- October 30, 2023
- AOSTIRMOTOR
Table of Contents
AOSTIRMOTOR S07-B Affordable 750W Electric Bike
Product Description
Safety Notice
To Ensure Your Safety, Make the Following Functional Checks Before Driving:
- Test brake system, throttle, and power system.
- Tire pressure should be at 30 psi.
- Check front wheel lug-nuts, securely tighten before every ride.
- Battery charge level- found on side of battery.
- Braking system adjustment and free operation.
Installation Instructions
-
Open your package.
-
Take out the tool box.
-
Take out the bicycle from the package and put it on a soft surface to avoid scratches.
Cut the tie that secures the front wheel to the side -
Remove the protective foam.
-
Open the accessory kit and remove the tool kit
-
Invert the bicycle.
-
Remove the large fixing bolt on the front fork.
-
Put the front wheel on the front fork and place the disc brake pad on the front wheel in the middle of the disc brake caliper Figure 1).
-
Use the supplied 15mm flat tool to tighten the two bolts.
-
Tie the key to the handlebar clamp, cut the zipper, and then use the Allen wrench in the tool kit to remove the clamp.
-
Place the handlebar in the middle position (Figure 2), install the rod clamp and tighten the screws with the included Allen wrench.
-
Install the LCD-display on the handlebar (Figure 3), tighten the screws, and connect the green connecting wire (Figure 4)
-
Grasp the bicycle light and unscrew the lens. Then, remove the plastic insulator, re-tighten the lens, and then connect the red cable (Figure 5), and connect the bicycle light to the screw above the front fork (Figure 6).
-
Install the pedal. The right pedal rotates clockwise (Figure 7), and the left pedal rotates counterclockwise (Figure 8). NOTE:Pedal mark “L” means left and “R” means right.
-
Vertical bicycle
-
Push the seat into the column, fix it in the desired position, tighten the screws, and then fix it.
-
Installation is complete. When connecting meters, headlights, brake circuit breakers, handlebars, etc., please align them and do not install violently(Figure 4).
Battery Installation & Maintenance
-
Please check the situation of the lock core before installation,Step 2 and Step 3 for details.
-
Turn your key counterclockwise to make the lock cylinder downward.
-
As shown in the left picture, align the slider
-
Install along the buckle
-
Battery installation complete
-
Turn on the switch and the battery is powered
-
When not using the battery for a long time, please charge it 1-2 times every month.
-
Please keep the key properly. If your key is lost, we can provide a new key according to the nameplate number on the key
-
Please keep the battery environment dry, for example, do not stay in the rain for a long time
-
Please use a universal meter to test the battery attenuation regularly
Display Use & Maintenance
SW-LCD display
- OPEN: Mode/M 1.5 seconds long press.
- CLOSE: In standby mode, long press Mode/M for 3 seconds
- SETTING: After booting, press UP+DOWN for 2.5 seconds(exit in the same way)
- The detailed settings are as follows: (on the boot state)
Wheel Diameter Setting:
- UP or DOWN
- 16-28inch (Default 26inch)
- Select, Mode Confirm
Speed Setting:
- UP or DOWN
- 12-45 KM/H
- Select, Mode Confirm
Light Setting:
- UP or DOWN
- 1-3 (Brightness)
- Select, Mode Confirm
MPH/KM Setting:
- UP or DOWN
- MPH or KM/H
- Select, Mode Confirm
SPEED Setting:
- UP or DOWN For 3 seconds
- MAX/AVG/NOW
- Select, Mode Confirm
RANGE Setting:
- PRESS Mode/M
- Riding mileage / accumulated total mileage
Front Light Open:
- Exit Settings
- UP FOR 3 Seconds
- Front lamp will work
- Default: 1
Power Shift Setting:
- Exit Settings
- UP/DOWN
- 1-5 (Power)
- Default: 1
Cruise Mode Setting:
- Exit Settings
- PRESS DOWN FOR 3 Seconds
- Default: 6KM/H
- Pushing state, non riding
- Ride your bike in a safe way. Don’t hit or knock the display.
- Keep away from the bad environments when use, such as downpour, large snowflakes and solarization.
- Try not to use in under-voltage condition.
- The screen will gets dark along with the temperature reduction when temperature below -10°C. The screen will return to normal when the temperature rises again.
Controller Use & Maintenance
Battery negative connection line
( Battery positive connection line
B Phase line – EROR 23
A Tail light wire
6 Integrated main line
6 Power sensor line
Motor Hall plug wire
1. Please be careful not to get water into the controller box
2. When the bike does not work: 1)Check the connection of controller cables;
2) Try to restart or Replace the controller; 3)Contact us with email
Motor Maintenance
- Please check the integrity of motor blocking piece regularly.
- Please check the integrity of cable before and after riding.
- Please check the integrity of motor shell before and after riding.
- Please do not use the motor in extreme environments, and do not let the motor work in water.
- When you find the motor power is insufficient, please get out of the bike and not force it.
FAQ
-
Is there a power usage or battery gauge on the bike?
Yes, there is a full screen LCD display. There is also an additional LED battery gauge on the side of the battery pack. 2x the info! -
Is there a switch to prevent accidental starting?
Yes, there is an on/off button on the battery pack. The brake levers also come standard with a safety power stop switch built in. -
How do I lock it up and what can I do to help minimize the chance of it being stolen?
AOSTIRMOTOR Bike has some great anti-theft features, including a locking battery rack with keys to keep bike safe, and rear wheel which is bolted down reduce the chances to be stolen.
Most standard U-locks and cable locks work fine on our AOSTIRMOTOR Ebike. -
Does it work in the rain?
The components are all waterproof and work very well in wet conditions,But we do not suggest to use our ebike in a rain day.
We suggest that you should keep your bike parked indoors and keep him in a dry situation.
POWER BRINGS JOY
www.AOSTIRMOTOR.com
aostirmotor@gmail.com