MEIKEE B0421TSFAMG Motion Sensor Light with 3 Adjustable Head Instruction Manual

B0421TSFAMG Motion Sensor
Light with 3 Adjustable Head
Instruction Manual

Thank you for purchasing MEIKEE products. To ensure a better shopping experience, please follow the instructions for use step by step.
If you have any questions about our products, please contact our customer service, our after-sales team will contact you at the first time and resolve any problems about the products.
E-mail: meikee@meikeelighting.com

Warning

1. The LED module can’t be replaced, you need to replace the entire lamp if it damaged or reach the service life.
2. If the wire is damaged, the lamp can no longer be used and needs to be scrapped.
3. If the casing breaks or water enters, the lamp can no longer be used and needs to be scrapped.
4. Do not stare at the LED light-emitting surface closely for a long time, to prevent the hurt of the eye.
5. Under no circumstances should the luminaire be covered by a thermal pad or similar material.
6. The Lamp requires professional electrician to install.
7. The IP66 waterproof grade is just for rainproof, the lamp can not be immersed in water, otherwise it may cause leakage.

Component and Structure diagrams

Parameter

Model| Wattage| Color Temperature| Lumens| Installation Height| Lighting Range
---|---|---|---|---|---
TSFA0042| 42W| 3000K| 3600LM| 5-7M| 4-6M
TSFA0042| 42W| 5000K| 3600LM| 5-7M| 4-6M
TSFA0042| 42W| 6500K| 3600LM| 5-7M| 4-6M

Input voltage: US: AC 120V/60HZ EU/UK: AC 230V/50HZ
CRI: >70
Waterproof Rating: IPG6
Working Temperature: -25-40°C

Installation Steps

1. Drill two holes on the mounting wall (the location of the holes refer to the mounting holes of the mounting base).

2. Use screws to fix the mounting base to the wall.

3. Set the illumination angle of the lamp according to your need, and tighten the screw handle.
   Note: When adjusting illumination angle of the main lamp, you need firstly loosen the screw handle, then adjust the lamp to a proper angle, and then tighten the screw handle. Note: For Sensor C, when setting the sensor, please open the waterproof plug at the bottom of the sensor firstly, and close the waterproof plug after setting done.

4. Set the lighting time and sensing distance on the sensor according to your need, and adjust the sensing angle at the same time.
   Lighting Time Switch: Press the switch 10S-45S-120S-600S cycle.

• The indicator light will stay on when switch to corresponding mode.
  Working Mode Switch: Press the switch Sun-24H- Moon cycle.
  Day mode: Lights up during the day and night, 24 hours working.
  24H: Manual Override Mode: Keep staying on, need to power off by the main power. (unaffected by sensor)
  Night Mode: Only work at night.

• The indicator light will stay on when switch to corresponding mode.
  Lighting Time Switch: Press the switch 10S-45S- 120S-600S cycle.

• The indicator light will stay on when switch to corresponding mode.
  Working Mode Switch: Press the switch Sun-Moon cycle.
  Day mode: Lights up during the day and night, 24 hours working.
  Night Mode: Only work at night.

• The indicator light will stay on when switch to corresponding mode. Note: Day mode: lights up during the day and night, that is working 24 hours
  Night mode: work only at night

  5. Disconnect the main power switch and connect the power cord. If the lamp power cord has a plug, please ignore this step.
  6. Turn on the main power switch or plug in the plug, the installation done.

Remind

The detection distance depends on the ambient temperature. If the ambient temperature is close to or higher than the human body temperature, this sensing detection distance will be shorter. This means you need to get closer to this light. Conversely, if  the ambient temperature is lower than the human body temperature, this sensing detection distance will be farther.

Routine Maintenance

1. To ensure the light working normally, please clean the lamps regularly.
2. Make sure the power is off before maintenance.
3. To avoid damage to the lamp, please do not clean it with chemicals.

Company name: Shenzhen Oumeike Lighting Technology Co.,Ltd.
Address: No. 19-20, Anye Road, Yuanshan Street, Longgang District, Shenzhen, Guangdong,
China (+86 0755-28608199)
C&E Connection E-Commerce (DE) GmbH
Zum Linnegraben 20, 65933, Frankfurt am Main, Germany
E-mail: info@ce-connection.de Tel:+49 (069) 27246648
CET PRODUCT SERVICE LTD.
Beacon House Stokenchurch Business Park, Ibstone Rd,
Stokenchurch High Wycombe HP14 3FE UK
Tel:+447419325266 E-mail: info@cetproduct.com
Contact: meikee@meikeelighting.com
Website: http://www.meikeelighting.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>