KOLPIN 21550 Rhino Grip XLR Instructions

KOLPIN 21550 Rhino Grip XLR

Product Information

The product is a 5KLQR*ULS;/5, designed to provide various features and functionalities. It is suitable for use in different settings and can be used for both indoor and outdoor purposes. The product is equipped with advanced technology and is designed to ensure user convenience and satisfaction.

Product Usage Instructions

1. Before using the product, make sure to carefully read the user manual and understand all safety precautions.
2. Ensure that the product is properly assembled and all components are securely attached.
3. Connect the product to a power source using the provided cable.
4. Press the power button to turn on the product.
5. Follow the on-screen instructions or refer to the user manual for specific settings and configurations.
6. To operate different functions, use the control panel or remote control, if included.
7. For maintenance and cleaning, refer to the user manual for specific guidelines.
8. In case of any issues or concerns, refer to the troubleshooting section of the user manual or contact customer support for assistance.
9. When not in use, disconnect the product from the power source and store it in a safe place.

For further information or inquiries regarding the product, please contact info@productcompany.com or visit our website at www.productcompany.com.

Product Instructions

Part No: 21550

Before you begin, read these instructions and check to be sure all parts and tools are accounted for. Please retain these instructions for future reference and part ordering information. Note: If any hardware is missing, do not return to the store. Call us to help, toll free at 1-877-956-5746.
These grips are designed to quickly and easily mount to any tubular bar (example UTV roll cage or ATV rack) or flat surface. The grips can be mounted in the vertical and horizontal positions. The kit fits tubing sizes from 3/4” to 2.0” diameter. Two hard-ware lengths are provided to accommodate large and small diameter tubing. You may need to trim the excess thread once installed. Failure to do so may result in damage to your vehicle.

K100149

9| 8| Hex Bolt, M6—1.0 x 60mm
10| 8| Locknut, M6—1.0
11| 4| Flat Rubber Pad (Not Shown)| –
12| 2| Rubber Strap (Not Shown)| 21591

Mounting Instructions

1. Position the Mounting Base (Item #6) on the roll bar/rack/flat surface where desired. The bottom of the Mounting Base has  two different shaped surfaces to fit large and small diameters, see below. Flat surface mounting will required drilling at this time to continue.
   

2. Insert the Hex Bolts [Item #8 or #9 depending on length needed] thru the Mounting Base [Item #6] and Metal Backer Plate [Item #7] on the opposite side of the roll bar/rack/flat surface. The Flat Rubber Pad [Item #11] can be placed between the Metal Backer Plate [Item #7] and the roll bar/rack to help eliminate the possibility of the Grips rotating and protect paint. Now loosely fasten the Locknuts [Item #10].

3. At this time the Grip Opening, Angle, and Rotation can be adjusted to fit desired items and vehicle accordingly. To do so, remove the Thumb Screw [Item #3] to allow the assembly to be disassembled and adjusted. Once adjusted, re-install the Thumb Screw [Item #3] and tighten to secure the Grip assembly.

4. Tighten the Locknuts [Item #10] evenly to torque specification.
   WARNING: Do not over tighten hardware or damage can occur. Item| Nm| kgfm| *lbfft**
   ---|---|---|---
   10| 5| 0.5| 4

5. Repeat above steps for installing the other grip assembly onto the opposite side.

6. Place desired item in Grips and connect Rubber Straps [Item #12] to the hooks on the outside of the Grips. Tension can be adjusted using different connection points and/or segments of the Strap.

Use and Care Information:

• Check the accessory mounts frequently and retighten if necessary.
• Replace this accessory with a new one if it is damaged or discolored excessively.
• When this accessory becomes dirty, rinse thoroughly with cool water to remove loose dirt, then wipe with a clean cloth or sponge.
• Never use petroleum solvents such as gasoline, thinner, benzene, acid or alkaline cleaners.
• Its recommended to keep out of direct sunlight exposure during long periods of time.

For additional assistance, please contact Kolpin customer service department at 877-956-5746 or 763-478-5800 or email customerservice@kolpin.com

One Year Limited Warranty

For the period of one (1) year from the purchase date, Kolpin will replace for the original purchaser, free of charge, any part or parts found upon examination by Kolpin to be defective in material, workmanship, or both.
All transportation costs incurred submitting product to Kolpin for warranty consideration must be borne by the purchaser. If Kolpin determines that the product must be returned to the factory for credit, please call 1-877-956-5746 for a Return Merchandise Authorization (RMA) number and shipping instructions.
This warranty does not apply to parts that have been damaged by accident, alteration, abuse, improper maintenance, normal wear, or other causes beyond the manufacturer’s control. In order to protect you and your ATV, certain parts of the accessory system and/or hardware are designed to fail when the equipment is over-stressed. Parts that are lost due to loosening and improper maintenance are not covered under warranty. This warranty does not cover removal or reinstallation labor fees of the accessory system and related components.
Peripheral products such as engines, electric motors, and actuators may carry an original manufacturer’s warranty. Most hardware is general in nature and is easily obtained locally. Be sure to replace with minimum metric class 8.8 specification.

Kolpin Outdoors, Inc. | 9955 59th Ave N | Plymouth, MN 55442
877-956-5746 or 763-478-5800 | kolpin.com | customerservice@kolpin.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>