BORMANN PRO BHA1950 Titanium Combi Kitchen Machine User Manual

BORMANN PRO BHA1950 Titanium Combi Kitchen Machine

• The above diagram may illustrate components related to other models in the product line and which may not included in the original packaging.

Safety instructions

When using electrical appliance, basic precautions should always be followed including the following:

• Read all instructions.
• To protect against risk of electrical shock do not put the appliance unit cord or plug in water or other liquid.
• Close supervision is necessary when an appliance is used by or near children.
• Unplug the appliance when not in use, changing accessory and before cleaning.
• Avoid contacting moving parts.
• If the supply cord is damaged, it must be replaced by manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
• The use of attachments not recommended or sold by the manufacturer may cause fire, electrical shock or injury.
• Do not use outdoors.
• Do not let cord to hang over edge of table or counter.
• Keep hands and utensils away from moving blades or discs while processing food to reduce risk of severe injury to person or damage to the food mixer.
• Blades are sharp, handle carefully.
• To reduce the risk of injury, never place cutting blades or discs on base.
• Be certain is securely locked in place before operating the appliance.
• Never feed food by hand, always use food pusher.
• Do not attempt to defeat the lid interlock mechanism.
• Always operate blender with cap is placed.
• When blending not liquid, remove center piece of two-piece cap.
• Turn off the machine before replace attachment.
• Use the product and assembly the accessory as mentioned on user manual only.
• Switch off the appliance before changing accessories or approaching parts which move in use.
• This appliance is not intended for use by children or other persons without assistance or supervision if their physical, sensory or mental capabilities prevent them from using it safely. Children should be supervised to ensure that they do not play with the appliance.
• Children should be supervised to ensure that they do not play with the appliance.
• For Europe countries: This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
• Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved. Children shall not play with the appliance.

Always disconnect the appliance from the supply if it is left unattended and before assembling, disassembling or cleaning.
Save these Instructions!

Description of main parts (Diag.A)

1. Ring nut
2. Fine mincing disk
3. Medium mincing disk
4. Coarse mincing disk
5. Cutter
6. Silicon coupling
7. Scroll
8. Meat grinder body
9. Meat tray
10. Tamper
11. Protective cover
12. Accessory socket
13. Swivel arm
14. Blender protective cover
15. Upper coupler
16. Safe micro-switch
17. Release button
18. Speed control knob
19. Motor house
20. Foot pad
21. Motor spindle
22. Lid
23. Bowl cover
24. Whisk
25. Flat beater
26. Kneading hook
27. Mixing bowl
28. Spatula
29. Middle cap
30. Blender lid
31. Jar
32. Cutting blade
33. Cup base

Operating Instructions

Control Panel Speed Setting

0: Stop
Setting 1-6: Operating speed
Setting 1: Minimum speed (slow)
Setting 6: Maximum speed (fast)
Setting P: Highest speed

Operating positions

Warning! Operate the appliance only when the accessory/tool is attached according to this table and is in the operating position.
Risk of injury from the rotating tools!
While the appliance is operating, keep fingers clear of the mixing bowl.
Do not change tools until the appliance is at a standstill and have been unplugged. When switch off, the drive continues running briefly.

How to use Kneading Hook, Flat Beater & Whisk

1. Place the appliance on a flat surface, e.g. a kitchen counter, and make sure it is standing firmly.
2. Ensure that the protective cover (11) is fitted to the Accessory socket (12)
3. Place the blender protective cover (14) into the upper coupler of swivel arm (15) (see illustration).

Turn the arm release button (17) clockwise at the same time lift the swivel arm (13) with hand so that it locks into place with a click, the swivel arm tilts up.

Fit the bowl cover (23) onto the swivel arm(13) and turn it slightly clockwise, so that it locks into position securely.

1. Place the food in the mixing bowl(27).
2. Fit the mixing bowl in the recess on the motor house(19).
3. Turn the mixing bowl slightly clockwise, so it locks into position.

1. Put the splashguard to swivel arm,as shown picture and ensure it fix well.

2. Fit the required accessory (25 with 24, 23or 26) onto the motor spindle (21) on the underside of the swivel arm(13).

3. A. The kneading hook (26) is used for heavy dough,minced meat or other demanding kneading jobs.
   B. The flat beater (25) is used to mix lighter types of dough.
   C. The whisk (24) is used for whisking cream, egg whites, etc.

4. Turn the accessory, so the pins on the spindle are aligned with the depressions on the accessory top edge. Press the accessory against the swivel arm and turn it anti-clockwise at the same time until the pins engage and the accessory locks into position securely. The accessory must not be loose nor should you be able to pull it free.

1. Lower the swivel arm so that it locks into place with a click.
   The lid (23) must fit tightly with the mixing bowl (27), otherwise it is fitted incorrectly. The appliance is now ready for use.

2. Plug the power cord into main power outlet and switches it ON. Turn Speed control knob to speed1(or any speed setting) indicator light on the control panel will now be illuminated.

3. Select the speed you want using Speed button 1 is the slowest and speed button 6 is the fastest speed. Recommended speeds, time and capacity are shown in the table above.

4. If you need to scrape inside the mixing bowl, wait until the accessory has stopped completely. Use the spatula, never your fingers.

1. Switch off the appliance by pressing the OFF button when you have finished mixing. Switch off the appliance at the switch and unplug it before you change the accessories, or before you take the appliance apart or when not in use.
2. Turn the swivel arm release button (17) clockwise. at the same time lift the swivel arm with hand so that it locks into place with a click. The swivel arm(13) tilts up.

1. Detach the accessory by turning it clockwise.
2. Remove mixing bowl with prepared food anti-clockwise.

IMPORTANT!
The temperature of water which will be added into dough at 40 +/- 5 o C when preparing for dough is on progress.

Meat grinder

1. Place the appliance on a flat surface, e.g. a kitchen counter, and make sure it is standing firmly.
2. Ensure that the protective cover (11) is fitted to the Accessory socket (12)
3. Place the blender protective cover (14) into the swivel arm (13). (see illustration)

1. Fit the scroll(7) into the meat grinder body(8).
2. Fit the silicon coupling (6) onto the scroll connection (see illustration).
3. Fit the cutter(5) onto the scroll connection (see illustration). The sharp edges of the cutter should point towards the mincing disk.
4. Fit one of the three mincing disk(2,3,4) on top of the cutter (see illustration). Turn the mincing disk so that two indentations are aligned with the pins on the meat grinder body. Select the mincing disk for the required consistency. You can choose fine, medium and coarse.
5. Fit the ring nut (1) over the mincing disk on the meat grinder body (see illustration). Turn clockwise to lock. The ring nut must hold the mincing disk securely in place. But do not over tighten.

If the meat grinder body (8) in the accessory socket (12),so that the arrow is aligned with the circle. Turn it to the vertical position, so the arrow is aligned with the arrow.

1. Fit the meat tray (9) onto the meat grinder body(8) so that the wide part is positioned over the motor house of the appliance.
2. Place the mixing bowl(27) or similar under the meat grinder body opening.
3. The appliance is now ready for use.

1. Plug the power cord into main power outlet and switches it ON.

2. Plug the power cord into main power outlet and switches it ON.
   Turn Speed control knob to speed1(or any speed setting) indicator light on the control panel will now be illuminated.

3. Cut your meat into smaller pieces, so the pieces fit into the feeding tube. Dice or cut into strips with a width of approx. 2.5 cm.

4. Put the pieces onto the tray(9).

5. Select the speed you want using the selector. Recommended speeds are shown in the table above.

6. The meat pieces travel down the feeding tube. Push down carefully with the tamper (10).
   Do not press too hard, otherwise you may damage the appliance.

1. Switch off the appliance by pressing the OFF button when you have finished grinding the meat. Switch off the appliance at the switch and unplug it before you change the accessories, or before you take the appliance apart or when not in use.
2. Remove pusher and meat tray.

To detach the meat grinder, turn the body so the arrow is aligned with the circle and then remove.

Fit the protective cover over the accessory socket again.

Safety instructions:

• Always remove bone,gristle, tendons, and rind before grinding the meat.
• Frozen food must be thoroughly defrosted before grinding.
• The meat grinder must only be used to grind meat. Avoid grinding pasty foods, e.g. food containing breadcrumbs, as this could damage the appliance.
• Never run the meat grinder continuously for more than 7 minutes. Running the meat grinder continuously for too long without a break may reduce the life span of the appliance. After having used the appliance for 7 minutes, take a break and wait at least 30 minutes before using it again.

Blender

1. Place the motor section on a flat surface, e.g. a kitchen counter, and make sure it is standing firmly.
2. Ensure that the protective cover (11) is fitted to the accessory socket (12).
3. Remove the blender protective cover(14) from the swivel arm(- see illustration).

1. Place the foodstuff you wish to process into the jar(31).
2. Put the blender lid(30) into the jar and ensure it cover well.
3. Place the middle cap(29) into the hole in the blender lid.

1. Place the jar assembly in the motor house,so that the arrow is aligned with the circle. Turn it clockwise, so the arrow is aligned with the arrow.
2. Plug the power cord into main power outlet and switches it ON.
3. Turn Speed control knob to speed1(or any speed setting) indicator light on the control panel will now be illuminated.
4. Select the speed you want using the selector. Recommended speeds are shown in the table above.

1. Switch off the appliance by pressing the OFF button after use. Switch off the appliance at the switch and unplug it before you change the accessories, or before you take the appliance apart or when not in use.
2. To detach the jar assembly, turn the jar so the arrow is aligned with the circle and then remove.
3. Remove blender lid then you may put processed food out.

Fit the blender protective cover to the swivel arm again.

Technical Data

Power: 1500W
Bowl capacity: 7,5L

Important tips and precautions

1. To achieve the best results when pureeing solid ingredients, place small portions into the jar one by one instead of placing a large quantity all at once.
2. If you are processing solid ingredients, cut them into small pieces (2-3cm) first.
3. When mixing solid ingredients start off first with a small amount of liquid. Gradually add more and more liquid through the opening in the lid.
4. Always place your hand on top of the blender when you are operating the device.
5. For stirring solid or very thick liquid ingredients we recommend that you use the blender in impulse mode to prevent the blades from becoming stuck.
6. NB: Operate the motor for a maximum of 1 minutes to prevent overheating or consequent damage.
7. It is advisable to wash appliance before using it for the first time.
8. Clean the appliance after each use, thereby avoiding liquid incrustations.
9. The switch does not permanently engage in the ‘P’ setting. You have to hold the switch in the ‘P’ setting

Cleaning

When cleaning the appliance, you should pay attention to the following points:

• Remove plug from the mains socket, and allow the appliance to cool down before cleaning it.
• Do not immerse the motor section of the appliance in water and make sure no water enters the appliance.
• Clean the motor section by wiping it with a damp cloth. A little detergent can be added if the appliance is heavily soiled.
• Do not use scouring pads, steel wool or any form of strong solvents or abrasive cleaning agents to clean the appliance, as they may damage the outside surfaces of the appliance.
• Take the appliance apart and clean all of the accessories separately. The meat grinder body and other parts can be cleaned in warm soapy water.
• Be careful not to touch the blades or sharp parts during use and cleaning.
• IMPORTANT! Allow to dry fully after cleaning before using again. Do not use the appliance if damp.
• We recommend you lubricate the meat screens with vegetable oil after cleaning, and store them in grease-proof paper to minimise the risk of rust and discolouration.
• After washing and drying, immediately place attachment into the protective sleeve for storage.

The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.

Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.

To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>