Tradeling HD-C77 Car Phone Mount User Manual

Tradeling HD-C77 Car Phone Mount

INTRODUCTION

Thank you for purchasing the HD-C77 Car Phone Mount. Please read this user manual carefully and keep it for future reference. If you need any assistance, please contact our support team with your product model number and Amazon order number

Package Contents

• Car Phone Mount
• User Manual
• Warranty Card
• Stabilizer
• Quick Start Guide
• Round Suction Cup

Product Diagram

Specifications

Getting Started

• Unscrew the pivot locking nut, let the ball joint pass through the fixed nut; then tighten the nut
• Clean a preferably flat surface on your dashboard where you want to install the mount with a mixture of equal parts (1:1) of isopropyl alcohol and water then wait for the surface to dry
• Carefully peel off the protective film of the 3M dashboard pad or 3M double-sided tape and fix it on the dashboard. Carefully peel off the mount base adhesive backing sheet and place the mount on the 3M dashboard pad or 3M double-sided tape
• Press down firmly, hold while pushing the mount locking lever back down again, and continue to hold down for a few minutes to ensure firm adhesion.
• For best results, allow 24 hours for the adhesive to securely bond with the surface before using the mount
• Carefully peel off the protective film of the stabilizer and then fix it in a suitable position on the extended arm, then fix it on the dashboard
• Press and hold the phone cradle release button until you can place your phone on the mount
• Adjust the phone cradle so it grips your phone. To ensure secure mounting, press the back edge of the clamp (not the front edge)

Product Care

• Don’t install the mount in front of the airbags.
• The temperature, pressure, cleanliness, and type of surface all affect the amount of time the adhesive takes to develop the bond

Attention

• Please install the car mount ina suitable place before starting9 the journey, do not operate and adjust the car mount while driving.
• Do not install the car mount in a position that interferes with the operation of the airbag or hinders driving.

Tips for Using the Suction Cup

• If the surface is flat and smooth, you can use the suction cup on the dashboard directly; While the surface is flat but not smooth, please use the suction cup on the dashboard pad.
• Do not stick the suction cup to curved surfaces, plush fabric or uneven surfaces. Otherwise it would not be attached securely.
• It is not recommended to attach the suction cup to the surface of leather, wall or glass film, because the suction cup with strong viscosity and attractiveness, which may cause surface damage.
• If the suction cup is frequently used in high temperature, low temperature or humid conditions, the suction force will decrease; Please avoid direct exposure to the sun for a long time.
• After using it for a while, if the suction is not sticky enough, please take down the suction cup and wash it with warm soap
• Water. It will be sticky again after drying.
• Please protect the suction cup with plastic wrap when not in use.

Note

• Choosing a flat surface on the dashboard, and clean the surface where you need to install the car mount with a wet cloth.
• Wait it to dry, and then install the 3M dashboard pad.
• Tear off the protective sticker of 3M dashboard pad, 3M double-sided tape, and car mount.
• Stick the pad to the position where you want to install the car mount.
• Press it firmly for 1 minute to fix it. Let it sit for 24 hours before installing the car mount.

Quick Start Guide

• Unscrew the pivot locking nut, let the ball joint pass through the fixed nut; then tighten the nut
• Carefully peel off the adhesive sheet on the base mount
• Push the suction cup lock up to fully open it. Carefully peel off the round suction cup adhesive backing sheet.

Assembling the Suction Cup

There are 2 ways to install the suction cup, which are listed as follows. Please choose among them according to your needs.

Install the car mount to a flat surface directly

• Install the car mount to a flat surface directly. Press it firmly for 1 minute to fix it.
• Must press the silicone suction cup one circle.
• Make sure it fits the surface completely
• Press down the suction cup lock to secure the car mount

Install the 3M dashboard pad on the dashboard first, and then install the car mount on the 3M dashboard pad

• Carefully peel off the protective films of the 3M dashboard pad.
• Fix to the dashboard. Press it firmly for 1 minute to fix it. Let it sit for 24 hours before installing the car mount.
• Attach the car mount to the 3M dashboard pad.
• Press down the suction cup lock to secure the car mount
• Then fix the stabilizer in a suitable position on the extended arm
• Press down firmly, hold while pushing back down, continue to hold down to ensure tight adhesion
• Press the phone cradle release button
• To ensure secure mount, press the back edge of the arm tips (not the front edge)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>