VEDINDUST EX706 4K HDMI Extender Over Cat5/6 Cable With POC User Manual
- June 14, 2024
- VEDINDUST
Table of Contents
VEDINDUST EX706 4K HDMI Extender Over Cat5/6 Cable With POC User Manual
Safety and Notice
Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.
- Follow all instructions and warnings marked on this unit.
- Do not attempt to service this unit yourself, except where explained in this manual.
- Provide proper ventilation and air circulation and do not use near water.
- Keep objects that might damage the device and assure that the placement of this unit is on a stable surface.
- Use only the power adapter and power cords and connection cables designed for this unit.
- Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
Features
- Each set includes one transmitter and one receiver.
- Use single UTP LAN cable (Cat5e/6) to substitute HDMI cable to achieve long distance transmission, the UTP Cable follows the standard of IEEE-568B.
- Transmission distance extend up to 40 meters under 4K/30Hz.
- Supports lossless compressed digital audio:Dolby TrueHD, DTS-HD Master Audio.
- Transmit Digital Audio and Video over the CAT5e/6 cable with zero signal loss.
- Data transfer speed 8.91Gbps.
- Support power over cable,
- DC 12V power supply.
Specifications
HDMI resolution: 4K30Hz/1080p/1080i/720p/576p/576/480p/4801
Support video color format: 8bit/deep color
Support audio format: DTS-HD/DolbytrueHD/LPCM7.1/DTS/Dolby-AC3/DSD
Max bandwidth: 297MHz
Max baud rate: 8.91Gbps
Input/Output TMDS signal : 0.5-1.5Volts p-p(TTL)
Input/Output DDC signal: 5Volts p-p (TTL)
Input cable distance : ≤3m AWG26 HDMI standard cable
Output cable distance: s3m AWG26 HDMI standard cable
Transmission distance: 4K/30Hz 40M Over single CAT5E/6/24AWG/Solid
Operating Temperature range : 32-104°F/0-40°C
Storage Temperature : 4-140°F / -20-60°C
Max working current: 12V/250mA
Power consumption: 3watts (Maximum)
Power adapter format Input: AC (50HZ, 60HZ):100V-240V
Operating Humidity range: 5 to 90% RH (No Condensation)
Dimension (L x W x H) : 61x53x16(mm)
Net Weight: 142g(pair
Package Contents
- Main Unit: TX & RX 1Set
- DC 12V power adapter: 1PC
- User manual: 1PC
Panel Description
- HDMI IN: HDMI input
- LED: POWER LED
- DC12V: 12V Power input
- EDID: EDID adjust button
- LED: OUT SIG LED
- RJ45: CAT6 UTP Output port
EDID Notice:
Copy mode: connect the display to the HDMI IN port, then press the button, it’ll copy the EDID to the extender. (After successful operation, the LED lights up for a few seconds and then goes off)
Reset EDID: Press the button for 3 seconds, it’ll reset the EDID to 4K30Hz stereo, (After successful operation, the LED will flash and then turn off)
- HDMI OUT : Connect to Display
- LED: SIG LED
- LED: POWER LED
- RJ45: CAT6 UTP Intput port
Wiring Diagram
How to Use:
- The HDMI output of the signal source is connected to the HDMI IN at the TX end.
- Connect the display device to the HDMI OUT port on the RX end.
- Connect one end of the Category 6 network cable to the TX end RJ-45 port.
- Connect the other end of the Category 6 network cable to the RJ-45 port on the RX end.
- Connect the 12V power plug to the DC 12V socket.
Before power on, please check the connection line carefully. And make sure that all interfaces are normally connected. The common troubles shooting way shows below:
| Trouble Description | Causes and solutions |
|---|---|
- Check if the power adaptor head is truly and correctly inserted the power socket.
- Check the power switch if it is in on status.
No Picture|
- Please to make sure that the connection devices has opened on and connected with the machine well.
- Check if the signal source is on and well connected.No Picture
- Check the system connection quality.
- Check if the line is all good quality.
- Check the cable quality.
Obscure Picture|
- Try again connect the cable to make sure the connection in good status.
- .Check the HDMI cable quality.