WUXI IDATA TECHNOLOGY COMPANY LTD IDATAP1MINI New Mobile Computer User Guide
- June 14, 2024
- WUXI IDATA TECHNOLOGY COMPANY LTD
Table of Contents
WUXI IDATA TECHNOLOGY COMPANY LTD IDATAP1MINI New Mobile Computer
FAQ
Frequently Asked Questions
- Q: What is the warranty period for the product?
- A: The product comes with a 12-month warranty for the whole device and battery, and a 3-month warranty for other accessories.
- Q: How can I contact after-sales service?
- A: You can reach the after-sales service hotline at 4008838268 #2 or via QQ: 2782597064.
- Q: What should I do if the device has performance issues?
- A: If you encounter any performance issues, refer to the issue handling section in the manual for troubleshooting steps. If the issue persists, contact after-sales service for assistance.
Overview
| 1 | Volume Button | 11 | MIC |
|---|---|---|---|
| 2 | TF/Nano SIM Slot | 12 | Right Scan Button |
| 3 | Scanner | 13 | USB Type-A |
| 4 | Power Button | 14 | USB Type-C |
| 5 | Scanning LED | 15 | DC Charging |
| 6 | Light Sensor | 16 | LED Flash |
| 7 | Front Camera | 17 | Rear Camera |
| 8 | Charging LED | 18 | Speaker |
| 9 | Left Scan Button | 19 | NFC |
| 10 | POGO PIN |
Charging
You can charge a battery:
- by using USB cable.
- by using * Single cradle.
- by using * DC power port.
Note
- Parts marked * needs to be purchased separately.
Charging LED indicator status:
- Charging: Indicator turns red.
- Fully charged: Indicator turns green.
Insufficient Battery:
- Screen shows battery less than 15%.
- Low battery deep.
- Indicator red blinks.
Issue Handling
- Issue: Can not power on.
- Fix: Use a USB cable to power the device or power the device through the DC port.
- Issue: When the device is connected to a USB charger or DC charger, the charging logo will not be displayed.
- Fix: Charge continuously for 1 hour, if still not wroking, contact after-sales service.
- Issue: Slow charging speed.
- Fix: Please confirm whether it is an original accessory for charging.
After-sale Service
- Hotline: 4008838268 #2
- QQ: 2782597064
Product Warranty
Mobile Smart Terminal Product Warranty
Dear Customer:
Welcome to choose mobile IoT terminal products! From the moment you purchase this product, you will have the following services:
[Free Maintenance]
- Since the date of your purchase, product performance failure caused by non-human damage, the whole device and battery warranty for 12 months, other accessories warranty for 3 months.
- Since receiving the problematic device, the after-sales service depart meant will send out the repaired device within 24 hours, the mostly minimize your maintenance waiting time.
- If the device has been repaired 3 times a year due to same problem, can exchange for a new device for free.
[Paid Maintenance]
In the following cases (including but not limited to), you can choose paid services:
- No warranty card or missing valid invoice or exceeding the warranty period;
- Damage caused by irresistible factors such as fire, flood, lightning, earthquake;
- Damage caused by failure to use, maintain or keep in accordance with the requirements of the product manual;
- Damage caused by unauthorised service personnel’s disassembly;
- Normal wear and tear during use of the product;
- The user’s own network and software cause the product to be unusable.
Note
- Required accessories for repairing are valid for a 1 year after the product discontinued.
FCC STATEMENT
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions
- this device may not cause harmful interference
- this device must accept any interference received, including interference that may cause undesired operation.
Turn on and enter the home screen
Steps for viewing E-Label:
- Step1: click “setting”
- Step2: click “about device”
- Step3: click “Certification” and display:
SAR Information Statement
Your New Mobile Computer is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health.
The exposure standard for New Mobile Computer employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. * Tests for SAR are conducted with the New Mobile Computer transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the New Mobile Computer while operating can be well below the maximum value. This is because the New Mobile Computer is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a New Mobile Computer model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government adopted requirement for safe exposure.
The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this New Mobile Computer when worn on the body, as described in this user guide, is 0.92 W/Kg (Body-worn measurements differ among New Mobile Computer models, depending upon available accessories and FCC requirements). The maximum scaled SAR in hotspot mode is 0.92W/Kg. While there may be differences between the SAR levels of various New Mobile Computer and at various positions, they all meet the government requirement for safe exposure. The FCC has granted an Equipment Authorization for this New Mobile Computer with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines.
SAR information on this New Mobile Computer is on file with the FCC and can be
found under the Display Grant section of http://www.fcc.gov/oet/fccid after
searching on FCC ID: 2ADE3IDATAP 1 MINI Additional information on Specific
Absorption Rates (SAR) can be found on the Cellular Telecommunications
Industry Association (CTIA) web-site at http://www.wow-com.com. * In the
United States and Canada, the SAR limit for New Mobile Computer used by the
public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard
incorporates a substantial margin of safety to give additional protection for
the public and to account for any variations in measurements.
The SAR test distance is 0mm.
- Safety measures for users and non-users
- Non-use of the device in certain situations (while driving) and certain places (airplanes, hospitals, gas stations and professional garages).
- Precautions to be taken by wearers of electronic implants (pacemakers. insulin pumps.
- neurostimulators, etc.) concerning in particular the distance between the device and the implant (15 centimeters) and the position of the device.
- During the call on the side opposite the implant.
- Advice for use to reduce the level of consumer exposure to radiation (e.g. Keep the device away from the human body during night rest or set it to flight mode, etc.).
- Recommendation of the use of the device in good reception conditions, to reduce the amount of radiation received (especially in an underground car park when travelling by train or car…).
- Indication of the parameters for good reception (e.g. display of four or five bars on the screen).
- Recommendation to use a hands-free kit and, in this situation. Precautions to be taken when
- Communicating: keep the device away from the abdomen for pregnant women or from the lower abdomen for teenagers.
CE Statement
Herby, Wuxi iData Technology Company Ltd.declares that this New Mobile Computer, iData P1 mini is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product allowed to be used in all EU member states.
- Use the New Mobile Computer in the environment with the temperature between OC and 45 C
- Use careful with the earphone maybe possible excessive sound pressure from earphones and headphones can cause hearing loss.
- Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
- The product shall only be connected to a USB interface of version USB-C.
- SAR: The device complies with RF specifications when the device used at 0mm from your body.
- The highest SAR value for this device when worn on the body is 1.51 W/ Kg
- 5150-5350MHz is resticted to indoor use only
- Adapter shall be installed near the equipment and shall be easily accessible.
The plug considered as disconnect device of adapter
Adapter Information:
- Model: TPA-141A050200VU01
- Input: AC 100-240V, 50/60Hz, 0.3A
- Output: DC 5.OV, 2.0A, 10.0W
- Operation Frequency:
- For BT/BLE: 2402MHz~2480MHz
- For 2.4G WIFI:
- 2412MHz~2472MHz (802.11b/802.11g/802.11n(HT20))
- 2422MHz~2462MHz (802.11n(HT40))
- For 5G WIFI:
- 5150MHz~5350MHz, 5470MHz~5725MHz,
- 5725MHz~5875MHz
- For GNSS:
- GPS: 1.57542GHz
- GLONASS: 1.602GHz
- Galileo: 1.561098 GHz
- For NFC: 13.56MHZ
- For GSM:
- E-GSM 900/GPRS 900/EGPRS 900:
- TX: 880MHz~915MHz; RX: 925MHz~960MHz
- GSM 1800/GPRS 1800/EGPRS 1800:
- TX: 1710MHz~1785MHz; RX: 1805MHz~1880MHz
- For WCDMA:
- UTRA Band I: TX:1920MHz~1980MHZ;
- RX: 2110MHz~2170MHz
- UTRA Band VIII: TX: 880MHz~915MHZ;
- RX: 925MHz~960MHz
- For LTE:
- LTE Band 1: (UL)1920MHz~1980MHz,
- (DL)2110MHz~2170MHz
- LTE Band 3: (UL)1710MHz~1785MHz,
- (DL)1805MHz~1880MHz
- LTE Band 7: (UL)2500MHz~2570MHz,
- (DL)2620MHz~2690MHz
- LTE Band 8: (UL)880MHz~915MHz,
- (DL)925MHz~960MHz
- LTE Band 20: (UL)832MHz~862MHz,
- (DL)791MHz~821MHz
- LTE Band 28: (UL 703MHz~748MHz.
- (DL)758MHz~803MHz
- LTE Band 38: (UL)2570MHz~2620MHz,
- (DL)2570MHz~2620MHz
- LTE Band 40: (UL)2300MHz~2400MHz,
- (DL)2300MHz~2400MHz
- Max output power:
- BT: 0.0087W
- BLE: 0.0048W
- 2.4G WIFI: 0.0238W
- 5G WIFI: 0.0266W
- E-GSM 900/GPRS 900/EGPRS 900: 1.8836W
- GSM 1800/GPRS 1800/EGPRS 1800: 0.9817W
- UTRA Band I: 0.2432W
- UTRA Band VIII: 0.195W
- LTE Band 1: 0.2799W
- LTE Band 3: 0.2931W
- LTE Band 7: 0.1679W
- LTE Band 8: 0.2612W
DECLARATION OF CONFORMITY
Contact
- Manufacturer: Wuxi iData Technology Company Ltd.
- Address: Floor 11, Building B1, No. VVV daolang East Road, Wuxi City, P.R.C.
- E-mail: zhangli@idatachina.com