AudioControl ACX-600.1 Compact High Power All-Weather Mono Amplifier User Guide

AudioControl ACX-600.1 Compact High Power All-Weather Mono Amplifier

Features

• Compact High Power Mono Subwoofer Amplifier
• High Current Design
• 1x 350 watts @ 4 Ohms
• 1 x 600 Watts @ 2 Ohms
• 12 dB/Octave Linkwitz-Riley Alignment Crossover
• GTO™ Signal Sense (Great Turn On)
• 2 RCA Inputs – switchable for Low and High Level signals
• Optional wired ACR-1 Remote Control for Output Level
• All-weather rated – IPX6 rated!
• Cage-free op-amps

Important Safety Instructions

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as mufflers, silencers, exhaust pipes, or other apparatus (including amplifiers) that produce heat.
9. WARNING: Improper installation may lead to permanent injury or death. Installation of the apparatus must be done with great care by qualified personnel, to prevent damage to fuel lines, power and other electrical wiring, hydraulic brake lines, and other systems, that might compromise vehicle safety.
10. Provide +12V and Ground wiring of sufficient size to ensure adequate current to the amplifier. For the ACX-600.1 this means 8 gauge wire or thicker.
11. Use rubber grommets to protect wiring whenever passing wires through metal openings or bulkheads.
12. Only use attachments/accessories specified by the manufacturer.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as the power input terminals are damaged or objects have fallen into the apparatus, does not operate normally, or has been dropped.
14. Fuses shall be replaced only with the correct type and fuse value, and only when the apparatus is powered off.
15. Exposure to high sound pressure levels may lead to permanent hearing loss. Take every precaution to protect your hearing.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure, that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Caution: to reduce the risk of electric shock, do not disassemble the apparatus, other than to remove the top panel to access the controls. There are no user-serviceable parts inside. Refer servicing to qualified personnel.

Recycling notice: If the time comes and this apparatus has fulfilled its destiny, do not throw it out into the trash. It has to be carefully recycled for the good of mankind, by a facility specially equipped for the safe recycling of electronic apparatii. Please contact your local or state recycling leaders for assistance in locating a suitable nearby recycling facility. Or, contact us and we might be able to repair it for you.

Connections & Control Panel Features

1. Speaker Output – Connect these wires to your subwoofer using the included water resistant harness. Speaker wire may then be crimped or soldered onto the bare leads. Use a decent sized wire gauge as this baby is powerful!
2. Power Input Terminal +12V & Ground – Connect these wires to the +12V and Negative binding posts of the vehicle battery via one of two included harness options. You may use either the included water resistant harness, or the included harness kit to terminate your own custom-length water-resistant harness. Use quality insulated wiring of the recommended wire gauge, such as wire gauge 8 or thicker.
3. Remote Power Input Wire – This wire connects to the 12V remote trigger output of some head units and controls the on/off state of the amplifier. Alternatively, you can use the GTO™ feature of the amplifier so it will turn on when an speaker level signal is detected at the RCA inputs.
4. Power LED – When the unit has been powered on, this LED will glow green and soft, like the understory of the Pacific Northwest Rain Forest on a rare, sunny day.
5. GTO ™ Signal Sense – In the ON position, the ACX-600.1 amplifier will turn on gracefully when it detects an incoming audio signal, and it will turn off after a period of time when the audio signal fades away to silence. In some situations, factory installed audio systems may turn on or “wake up” due to convenience features like door chimes, alarms, and cell phone signals that trigger the source unit in the vehicle to come on. To prevent these from turning your audio system on unexpectedly, you can bypass the GTO™ circuit by moving the switch to the OFF position and use a switched 12-volt signal connected to the Remote In wire instead.
6. Protection LED – This LED will shine if there is a problem being sensed by the unit. If this lights up, remove the speaker connection and RCA inputs and try again. If error clears, examine your speaker, speaker wires, and RCAs for possible causes of short. If the issue still persists after removing the speakers/RCAs, best to call the lonely folks in tech support.
7. Gain Control – This control allows you to adjust the overall output level. Turn clockwise to increase, and counter-clockwise to decrease. With the source unit set to 75%, adjust this knob to the point where the Maximized light shines briefly. This will be your optimal gain setting.
8. Low Pass Crossover – A crossover allows you to match a speaker to the frequency range it is designed to handle. Choosing the crossover point recommended by the speaker manufacturer will provide increased speaker reliability and optimum sound quality. The ACX-600.1 amplifier has selectable low pass crossover frequencies at 80 Hz, 120 Hz, and a “bypass” option. The amplifier reproduces the frequency range below the selected crossover frequency.
9. Gain Maximized LED – This LED indicates when the ACX-600.1 amplifier gain has been maximized for optimum performance. With your source unit turned up to 75%, use your gain controls to dial in the output by watching for this LED to shine, then back it off just a touch.
10. AccuBASS® – This switch enables the renowned AccuBASS® bass enhancement to work it’s magic on the lower bass of speaker outputs.
11. AccuBASS® Threshold – Sets the level at which AccuBASS® will begin to work.
12. AccuBASS® Level – Adjusts the level of the AccuBASS® enhancement circuitry.
13. Input Level – Use this switch to specify which type of signal input voltage type you are using – high is speaker level & low is RCA line level.
14. Remote Level Port – Using the cable that came with the ACX- 600.1, connect your optional ACR-1 level control knob here.
15. RCA Inputs – This is where you connect your source signal to. If using low level signals, make sure your Input Level setting switch is set to Low. If you are using high or speaker level signals, set your Input Level to High.

Power Connections

• In this example, the head unit has a +12V trigger output that is connected to the ACX-600.1 remote input terminal. When the head unit is turned on, it will turn on the ACX-600.1 amplifier.
• Alternatively, the GTO™ Signal Sense feature can be used to gently turn on the ACX-600.1 amplifier when an audio input signal is detected. (The connection to the ACX-600.1 remote input terminal is not required when using the GTO™ Signal Sense.)

System #1: Using Speaker-Level Inputs & GTO™ Signal Sense Turn On

Cover Plate Removal

The cover plate must be removed to gain access to the controls, and then sealed again to protect the controls against moisture and debris.

Removal Procedure

1. Locate the top six hex screws that hold down the sealed top cover.
2. Use a 2.5mm hex wrench to remove the six screws.
3. Gently lift cover off. It’s a very tight fit there, so you may need to use some gentle force. Yes, it is with you!
4. Keep the cover plate and screws in a safe and handy place, until you have finished adjusting the controls to your immense satisfaction.

Specifications

All specifications are measured at 14.4 VDC (standard automotive voltage). As technology advances, AudioControl reserves the right to continuously change our specifications, like our Pacific Northwest weather, although we are working on changing that as well.

The ACX-600.1 Amplifier

• Power Output (RMS) . . . . . . . . . . . . . . . . . . . . . . . . . .1×350 Watts @ 4 Ohms
• . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1×600 Watts @ 2 Ohms
• Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Hz – 20 kHz
• Total Harmonic Distortion + N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0.05%
• S/N Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . 102 dBa, Ref 175 Watts @ 4 Ohms
• Power / Ground Wire Gauge . . . . . . . . . . . . . . . . . . . Between 8 and 4 AWG
• Recommended fuse rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Amps
• Crossover . . . . . . . . . .12dB/Octave Linkwitz-Riley, 80 Hz, 120 Hz, Bypass
• Line/Speaker-Level Inputs. . . . . . . . . . . . . . . . . . 500mV – 6V/1V – 12VRMS
• Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.45 lbs
• Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.89” W X 5.31” D X 2.36” H

Warranty

For details of the limited warranty for your ACX-600.1, please visit the following page on our website: audiocontrol.com/warranty Please keep your receipt in a safe place.

AudioControl, Inc. 22410 70th Avenue West Mountlake Terrace, WA 98043 USA Phone: 425-775-8461 email: sound.great@audiocontrol.com

MOBILE ELECTRONICS

AUDIOCONTROL ALL-WEATHER AMPLIFIERS

Here in the Pacific Northwest, if you’re outside, chances are, you’re getting soaked by Rainforest-nourishing rain, drenched in salt spray from the Puget Sound, or muddied in the boggy trails of the Cascade Foothills. And if you’re passionate about audio, your music goes where you go. Don’t let extreme conditions get in the way of rocking to your favorite sound track on your next overland or seagoing adventure. AudioControl’s ACX All-Weather Amplifiers deliver honest power levels to the sound system in your boat, UTV, motorcycle, and more. The variety of multi-channel amplifier options in the ACX line-up gives you the flexibility to build the perfect system and ensure your open-air speakers deliver plenty of punch and clarity, all day long. Looking to add a subwoofer with independent level control? We’ve got you covered with the ACX-300.1 and ACX-600.1 and the optional ACR-1 remote. Installer friendly, heavy gauge quick connect wiring makes installation quick and painless, making ACX amplifiers the perfect solution for your next adventure.

• High Power Output from a Compact Chassis
• IPX6 Rated
• Bridgeable (Select Models)
• AccuBASS® Bass Restoration (Select Models)
• Optional Remote Level Control (Select Models)
• High/Low Input Modes
• GTO™ Signal Sense
• Linkwitz-Riley Crossovers
• lnstaller Friendly Quick Connect Wiring

AudioControl ACX All-Weather Amplifiers are built tough from solid aluminum extrusions, sealed tight against the elements, and ready for your extreme lifestyle. Fully sealed quick connect wiring, and a water-tight chassis add up to an IPX6 rating, ensuring ACX amplifiers deliver the pure, uninterrupted power AudioControl is known for.

Quick connect wiring pigtails and male power connector included with all models. *Included connectors will vary based on model.

©2020 AudioControl, Inc. All rights reserved. Features, appearance and specifications subject to change without notice. www.audiocontrol.com

References

• Terms and Privacy - AudioControl
• Home - AudioControl

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>