BORMANN BEH5250 Floor Heating Panel Instruction Manual
- June 4, 2024
- BORMANN
Table of Contents
BORMANN BEH5250 Floor Heating Panel
- The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
- Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.
- To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.
Introduction
To get the most out of your new heater, please read through these instructions and the attached safety regulations before use. Please also save the instruction manual in case you need to remind yourself of the heater’s functions at a later date.
Safety instructions
Important Before plugging the unit into the mains, ensure by visual
inspection that the unit is intact and has not suffered any damage during
transportation.
Caution The appliance must be always placed on a flat and stable surface.
In order to avoid a hazard due to inadvertent resetting of the thermal cut-
out, this appliance must not be supplied through an external switching device,
such as a timer, or connected to a circuit that is regularly switched on and
off by the utility.
For your own safety
- Read all instruction before using the heater.
- Only connect the heater to a single-phase socket with a mains voltage as specified on the rating plate.
- Do not leave your home while the appliance is in function: ensure that the switch is in OFF (0) position and the thermostat is in minimum position. Always unplug the appliance.
- Keep combustible material such as furniture, cushions, bedding, paper, clothes, curtains etc. at least 100cm away from the heater.
- Do not hand anything on or in front of the heater.
- Always use the heater in an upright position.
- Do not place the heater against walls, furniture, curtains, etc.
- Do not use the appliance in rooms less than 4m² area.
- Always unplug the heater when not in use. Do not pull the cord to unplug the heater.
- Keep the air inlet and outlet free from objects at least 1m in front and 50cm behind the heater.
- Do not install the heater immediately below a socket- outlet.
- Do not let animals or children touch or play with the heater. Pay attention the air outlet gets hot during operation.
- Do not cover. If covered, there is the risk of overheating.
- Do not use this heater in the vicinity of showers, bath tubs, wash basins or a swimming pool etc.
- Do not use the heater in the rooms containing explosive gas inflammable solvents, varnish or glue.
- Keep the heater clean. Do not allow any objects to enter any ventilation or exhaust opening as this may cause electric shock, or fire or damage to the heater.
- If the heater has been dropped or damaged it should not be used until it has been inspected by a qualified service center.
- Close supervision is necessary when the heater is being used by or near children, persons suffering from any physical impairment or pets.
- Do not use to dry clothes or any fabric.
- Do not use the heater to dry your laundry. Never obstruct the intake and outlet grilles (danger of overheating).
- Do not move the appliance while it is functioning in order to avoid overheating with the additional risk of fire.
- If any part of the heater or supply cord becomes damaged, it must be replaced by a qualified electrician. In order to avoid a hazard.
- The heater must not be located immediately below a socket- outlet.
- Do not use this heater with a programmer, timer or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly.
- Do not leave the heater switched on when leaving your home or going to sleep.
- Children should be supervised to ensure that they do not play with the appliance.
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience or knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
- Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- Children of less than 3 years should be kept away unless continuously supervised.
- Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
- Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
- Do not leave unattended when plug in to the mains supply.
Caution Some parts of the heater can become very hot and cause burns. Do
not touch hot surfaces. Particular attention has to be given where children
and vulnerable people are present.
Note
These heaters are intended for domestic use only. They can be used as both
portable appliance and wall mounting appliance.
Installation
Installation while use on the floor as portable appliance
Please attach the feet on the heater’s housing, and fixing them with supplied
ST4x12mm(8pcs) screws.
Wall mounting (While use the heater as fixed appliance)
Please note that the product must be installed at least 15 cm from the floor and 50 cm from the ceiling.
For wall mounting study scheme
- Install the bracket with screws firstly, see the image 1.
- Drill the holes at each sides on the wall, then insert the plastic expanded plugs within, Fix the bracket in the wall with screw,see the image 2.
- Fit the heater into suitable position ensuing that the holes align with bracket see image 3.
- Tight the screw on the top of bracket to catch steady.
Operating instructions
Insert the plug into a suitable socket outlet on an A.C. power supply having
the same voltage as that shown on its rating label. The touch screen buttons
located on the product correspond to the remote control functions:
Control panel
- Display
- Temperature“+” button
- Temperature“-“ button
- Power button
- Mode button
- Timer button
- Receiver
- Child clock button
-
Power function
Before you working the heater,your should turn on the switch in side.
Press “ ” to set functions. The upper part of the display shows the room temperature The heater is working at low power heating conditions. -
Mode
Press “ ” to regulate low ” ”, or high temperature power ” ”. -
Temperature selection
Press “+” or “-” button to select the desired temperature from a range of 5°-40°C. The temperature indicator will remain lit for a long time. -
Timer
Press the timer button ” ”, to select the desired range between 1 hour to 24 hours. The remaining time will appear. -
Child clock
Press the child clock button for 3 seconds, ” ” will be display on the screen,so you can not make any operate beside ” ”, and same ways to touch to delete the child clock function.
WIFI Function
-
Use your phone to scan the QR code (page 2)or search “Tuya Smart” in Application on market to download and install the App.
-
Select your country code, enter the cellphone number and tap “Get” to get a message containing verification on code.
-
Enter the verification on code in the message and tap“Login” to login the App.
-
Go to the App, tap “add device” at the bottom, as shown in the picture 1.
-
There are two connection on methods for the App (hotspot mode and quick connect mode). The quick connect mode is the default mode. Users could tap the upper right corner to switch the connection on method to hotspot mode.
- For quick connect mode, please make sure the device’s instructor light quickly flashes.
- For hotspot mode, please make sure the device’s instructor light slowly flashes.
- If the light is not flashing as the status as above described, please long press the device’s reset button for 5 seconds or longer until it flashes correctly as shown in the corresponding picture (page 2).
-
Select the Wi-Fi, enter password and tap “Next”, as shown in the picture 2 (page 2).
For quick connect mode, the App interface will go through the changes during the network configuration on process as shown in the picture 3, Picture 4 shows the interface when the device is connected successfully. -
After the device is connected successfully, tap “Devices” at the bottom. The device name shows in the list in the picture 5. Tap it to enter the control panel of the device.
Remarks:
When device is online, there will be a green dot at the front of the device icon;
When the device is offline, the dot will be grey;
If is the device shared by others, there will be double loop. -
My profile” is where users could manage personal information. The key information is as follows see picture 6:
- Personal information: including account name and cellphone number.
- Information of shared devices.
- Message center.
- Entry to submit feedback.
- F.A.Q.
- Phone binding: if you sign in with social network account, you could bind your phone number with your account
- About
-
Add sharing: As shown in the picture, users could type in a new member’s cellphone number and share the device with him. The new member could con-trol the device with his own account, see picture 7.
Operating sound
The appliance emits a beep upon each operation setting.
Technical Data
- POWER: 2000W
- 2 HEAT SETTINGS
- LED DISPLAY
- ADJUSTABLE THERMOSTAT
- OVER HEATING PROTECTION
- 24H TIMER
Cleaning and maintenance
Before cleaning always remove the plug from the electrical socket outlet.
Clean the air inlet and outlet grilles frequently.
Never use abrasive powders or solvents.
Disposal Information
Should you want to dispose of this item please do not put it with the
household waste. Used electrical and electronic equipment and batteries must
be made available for separate collection.
Private households may return their used electrical and electronic equipment
to designated collection facilities free of charge. Identify where your local
col-lection points are and return the product there. (Facilities are usually
available at the municipal waste site. Υour electrical retailer, or your local
authority may provide separate collection from the household.)
By disposing of this product correctly you will be providing positive help to
the environment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>