Foiresoft W50 Cordless Zebra Roller Blinds User Manual
- June 14, 2024
- Foiresoft
Table of Contents
Foiresoft W50 Cordless Zebra Roller Blinds User Manual
PRODUCT WARRANTY
Foiresoft provide a limited warranty service for 6 months after the date of purchase. The support we provide under the limited warranty is only available for manufacturing defects (i.e, material defects, workmanship that cause product failure to operate).
What is covered?
- Wrong Type, Color, and Size
- Package Damaged
- Missing Accessories
- All internal mechanisms
- Repairs and/or replacements will be provided with the closest equivalent of the product
NOTE : For the issues mentioned above (wrong type, color, size, and damage/defective product), order number, product size and pictures must be provided.
What is NOT covered?
CONTACT INFORMATION
Foiresoft Customer Service :
GETTING STARTED
-
INCLUDED COMPONENTS
-
TOOLS YOU MAY NEED (NOT INCLUDED)
PARTS NAME
PARTS DIMENSIONS
HOW TO INSTALL
INSTALLING TIPS
- Make sure the blinds are fully rolled up to ease the installation.
- Confirm the direction of the header’s front side and back side before installing.
- Check the space for check if the surface is flat to ensure that the blinds will be able to be installed beautifully.
- Check the components included are all complete. If you are missing some parts, please reach out to us for replacement.
01) Marking the bracket location
Before marking the bracket location, please make sure that the location for bracket installment won’t interfere other components including the blind’s header. (Refer to page 4 for bracket dimensions.)
02) Installing the C-Clamp direction
Please refer to the explanation picture for checking the right C-Clamp direction for installment.
03) Installing the blinds
The front part of our header has rounded edge. Please make sure the installment directions.
HOW TO INSTALL
CEILING MOUNT
WALL MOUNT
PRECAUTIONS FOR USING
OPENING AND CLOSING THE BLINDS
- Place the handle on the exact center of the bottom bar and slowly raise or lower the blind.
ADJUSTING SPRING TENSION
NOTES
- Our shade is operated by the spring tensioner that is located on the center pole.
- The spring may be loosened or tightened depending on the long use of the blind or the external environment such as humidity and heat.
- The spring tensioner is on the right when viewed from the front
ADJUSTING THE FABRIC
Due to working mechanism, there’s a size gap between the fabric and the
header.
The total size gap will be around 1.5 inch and the fabric usually will be off
centered because the spring tension device parts are all on the right side.
Therefore, usually the gap on the right side will be bigger than the left
side.
If you’d like to adjust the fabric location to the center, you can open the blind fully and slowly close it while shaking the fabric left to right. If this doesn’t work in one try, please do the adjustment repeatedly.
TELESCOPIC DRAW ROD
- NOTES : The telescopic draw rod is not included on the package. It has to be purchased separately.
CLEANING GUIDES
How to remove stain
Use soft brush to remove dust. Please do not use any wet equipment to clean
the shade.
Use a hair dryer on cold mode or soft brush to remove dust and use neutral
detergent for stain spot cleaning.
Do not dry the fabric in direct sunlight.
OTHER REFERENCES
How to measure inside mount video guidelines
[ Amazon US ]
https://www.amazon.com/vdp/0494ffecfb2b420fa99a58afa0250e81?
[ Amazon.CA ]
https://www.amazon.ca/vdp/0ba807b3b7bd474286bfc5133f1fbab0
How to measure outside mount video guidelines
[ Amazon US ]
https://www.amazon.com/vdp/013b2c01b14a451895e7579501db95b8?
[ Amazon CA ]
https://www.amazon.ca/vdp/0868eaf99c05419f8c6801e4eec2be82
References
- Amazon.CA
- Amazon Sign In
- How To Measure For Outside Mount(DO1)
- How To Measure For Inside Mount(DI1)
- Amazon Live - How To Measure for Outside Mount Shades and Blinds (B0104)
- Amazon Live - How To Measure for Inside Mount Shades and Blinds (B0104)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>