SEVENTEEN SVFA23JO Official Light Stick User Guide
- June 13, 2024
- SEVENTEEN
Table of Contents
- SEVENTEEN SVFA23JO Official Light Stick
- Product Information
- Product Usage Instructions
- How to Insert or Replace Batteries
- Using BASIC MODE
- Using COLOR SHAKING MODE
- Using BLUETOOTH MODE
- Warranty
- Paid Repair Service Eligibility
- Product specifications
- FCC
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SEVENTEEN SVFA23JO Official Light Stick
Product Information
- Product Name: SEVENTEEN OFFICIAL LIGHT STICK VER.3
- Model Number: SVFA23JOS900NN0
- Dimensions: 238x97x97mm
- Weight: 229g
- Manufacturer: Elcomtec Co., Ltd
- Power Source : AAA 3 batteries (DC 4.5V)
- Certification: R-R-1EL-SVFA23JO(KC)
- Contact Information: E-mail: llight-stick.support@hybecorp.com
Product Usage Instructions
How to Insert or Replace Batteries
-
Turn the battery cover at the bottom of the handle counterclockwise and remove the battery holder located inside.
-
Place three alkaline AAA batteries into the battery holder as shown in the figure.
When assembling batteries, make sure to connect the + and – terminals correctly; the terminal with a spring is the -, and the terminal without a spring is the +. -
After placing the batteries, place the battery holder in the direction of the arrow and close the battery cover by turning it clockwise.
Note : Opening the battery cover while holding the product upside down may cause the replaceable holder to disassemble and the product to fall off. Please open the battery cover carefully.
Precautions for Handling Light Stick
- When reassembling the light stick part after disassembling it, place it so that the triangle faces the front center and then assemble it.
- When reassembling the replaceable handle, check the direction of the protruded anchor before assembling it.
Handling Precautions
- Avoid high temperature or humidity; store at room temperature.
- Do not allow the LED light to shine directly in the eyes from a close distance.
- Avoid dropping the product or applying excessive force or pressure as it may affect the LED color.
- Be careful not to swallow parts or put them in the mouth.
- Avoid applying excessive force or pressure or placing the product in contact with water as it may cause the product to malfunction.
- Stop using the product when damaged, and do not arbitrarily disassemble the product to repair or modify.
- When batteries die, put in new batteries. When not using the product for a long time, remove the batteries.
- Keep used batteries out of reach of children or dispose of them at a designated disposal site.
- Must use genuine AAA batteries, and check the +/- terminals when installing them. Otherwise, product damage and fire could occur.
- The product may cause interference while in wireless operation.
Note : For detailed instructions on using the product with a mobile app, refer to the User Guide provided with the product.
How to Insert or Replace Batteries
- Turn the battery cover at the bottom of the handle counterclockwise and remove the battery holder located inside.
- Place three alkaline AAA batteries into the battery holder as shown in the figure.
- When assembling batteries, make sure to connect the + and – terminals correctly; the terminal with a spring is the – terminal, and the terminal without a spring is the + terminal.
- After placing the batteries, place the battery holder in the direction of the arrow and close the battery cover by turning it clockwise.
- [Figure 1] Opening the battery cover while holding the product upside down may cause the replaceable holder to disassemble and the product to fall off. Please open the battery cover carefully
Precautions for Handling Light Stick
- [Figure 2]When reassembling the light stick part after disassembling it, place it so that the triangle face the front center and then assemble it.
- [Figure 3]When reassembling the replaceable handle, check the direction of the protruded anchor before assembling it.
Turning the Product On/Off
- Press and hold BUTTON ① to turn on the product. Once powered on, the product automatically enters BASIC MODE.
- Press and hold BUTTON ① to turn off the product.
Using BASIC MODE
- To change the color of LED, press BUTTON ①.
- To change the flashing speed of LED, press BUTTON ②.
- The flashing speed will change from Long > Medium > Fast > On (flashing off)
- Press and hold BUTTON ② to switch to COLOR SHAKING MODE.
Using COLOR SHAKING MODE
- While the product is powered on, press and hold BUTTON ② to switch to COLOR SHAKING MODE. The LED color will change every time you shake the product.
- Press and hold BUTTON ② to switch back to BASIC MODE
Using BLUETOOTH MODE
- Turn on BLUETOOTH MODE on your mobile device, and press and hold BUTTONS ① & ② at the same time. The LED light will flash blue and the product will try to connect to the mobile device via Bluetooth. When successfully connected to Bluetooth, the LED light will change to the color you set on the app.
- Press and hold BUTTONS ① & ② at the same time to switch back to BASIC MODE.
- Buttons do not work in BLUETOOTH MODE, so it is not a product defect.
- Bluetooth and your smartphone could be disconnected intermittently while in use.
- Only Bluetooth 4.2 or higher is supported
CONCERT MODE
- To use CONCERT MODE at an offline concert, enter your seat number directly on the app or use the pairing booth at the concert venue. Once paired, turn on the product to enter CONCERT MODE.
- Depending on the concert, pairing may not be available. Please refer to the guideline provided by your event host for details.
- Buttons do not work in CONCERT MODE, so it is not a product defect.
- If pairing continues to fail, please contact the pairing booth at the concert venue.
Handling Precautions
- Avoid high temperature or humidity; store at room temperature.
- Do not allow the LED light to shine directly in the eyes from a close distance.
- Avoid dropping the product or applying excessive force or pressure as it may affect the LED color.
- Be careful not to swallow parts or put them in the mouth.
- Avoid applying excessive force or pressure or placing the product in contact with water as it may cause the product to malfunction.
- Stop using the product when damaged, and do not arbitrarily disassemble the product to repair or modify.
- When batteries die, put in new batteries. When not using the product for a long time, remove the batteries.
- Keep used batteries out of reach of children or dispose of them at a designated disposal site.
- Must use genuine AAA batteries, and check the +/- terminals when installing them. Otherwise, product damage and fire could occur.
- The product may cause interference while in wireless operation.
How to Check if Bluetooth is Working on the Light Stick
- Launch the mobile app, and select SELF MODE.
- Press the two buttons on the product at the same time for more than 2 seconds to check if the light flickers in blue.
- When the light flickers in blue, it means that the product has been successfully connected to the mobile app via Bluetooth.
- Check that the colors of the product on the mobile app and the actual product are synched, then press ‘OK’ or ‘CANCEL.’
- Select a color of your choice from the color palette on the mobile app and visually inspect if the product changes to the selected color.
- When the color of the product changes to the one you selected on the mobile app, this means that Bluetooth is working properly.
- If Bluetooth is disabled on the mobile app, the product connection may fail.
- If not working properly, close the mobile app, enable Bluetooth on your mobile device, and open the mobile app again.
- Repeat Steps 1 to 5 above after opening the mobile app to ensure that Bluetooth is working properly.
Warranty
- This product is made through a strict quality control and inspection process.
- If the product malfunctions even though handled properly by the user, free repairs will be provided within the warranty period.
- Please present this warranty when requesting repairs.
- Please keep the purchase receipt as this warranty is valid only for products purchased through an official retailer.
- Warranty is valid for three months from the date of purchase.
This warranty does not cover malfunction caused by user’s negligence or misuse.
Paid Repair Service Eligibility
- If the warranty is expired
- If the product malfunctions or is damaged due to user’s negligence or misuse
- If the product malfunctions due to natural disasters, such as flood, fire, and earthquake.
- If the consumer wants the case replaced due to scratches that occurred while using the product
- If the consumer has repaired the product at an unauthorized repair service center, or if the consumer arbitrarily disassembled, repaired, or modified the product
Product specifications
NAME | SEVENTEEN OFFICIAL LIGHT STICK VER.3 |
---|
MODEL
SIZE
| SVFA23JOS900NN0
238x97x97mm / 229g (batteries excluded)
COMPONENTS| Light Stick, dust bag, strap, product manual
POWER| 3 Alkaline AAA Batteries (sold separately), DC 4.5V
Manufacturer| Elcomtec Co., Ltd
Authentication| 2A9BA-SVFA23JO(FCC)
|
Email address for repair
E-mail : light-stick.support@hybecorp.com
Warranty period : 3 months from the date of purchase(Receipt verification
required)
Responsible Party
HYBE AMERICA INC.
2121 Avenue of the Stars, Fox Plaza, Suite 2570 Los Angeles, State of
California CA 90067
FCC
This device can be operated in at least one Member State without infringing applicable requirements on the use of radio spectrum. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : – Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help This device comply with part15 of FCC rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device & its accessories must accept any interference received, including interference that may cause undesired operation.
Part 15.21 statement
Changes or modifications not expressly approved by the manufacture (or party
responsible) for compliance could void the user’s authority to operate the
equipment FCC ID : 2A9BA-SVFA23JO
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. End users must follow
the specific operating instructions for satisfying RF exposure compliance.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
RF Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. End users must follow the specific operating instructions for satisfying RF exposure compliance.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>