Conrad RF-TTLP4-01 HT300 Thermal Label Printer User Guide

: June 15, 2024
: CONRAD

Table of Contents

Intended use
Delivery contents
Operating instructions
Description of symbols
Safety instructions
Getting started
Disposal
Technical data
Documents / Resources

Quick Start Guide
RF-TTLP4-01/HT300 Thermal Label Printer
Item no: 2734626

Intended use

The product is a thermal label printer.
The product is intended for indoor use only. Do not use it outdoors.
Contact with moisture must be avoided under all circumstances.
If you use the product for purposes other than those described, the product may be damaged.
Improper use can result in short circuits, fires, electric shocks or other hazards.
The product complies with the statutory national and European requirements.
For safety and approval purposes, you must not rebuild and/or modify the product.
Read the instructions carefully and store them in a safe place. Make this product available to
third parties only together with these instructions.
All company names and product names are trademarks of their respective owners. All rights reserved.

Delivery contents

■ Printer	■ Ribbon core
■ Power adaptor	■ Ribbon
■ Mains cable	■ Paper roll
■ USB cable (USB-A to USB-B)	■ Quick start guide
■ USB memory stick

Operating instructions

Download the latest operating instructions from www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.

Description of symbols

The following symbols are on the product/appliance or are used in the text:

Read the operating instructions carefully.
The symbol warns of hazards that can lead to personal injury.
The symbol warns of dangerous voltage that can lead to personal injury by electric shock.
****This product must only be used in dry, enclosed indoor areas. It must not become damp or wet.
The symbol warns of hot surfaces that can result in severe burns when touched.
Read the information carefully.

Safety instructions

Read the information in this document carefully and especially observe the safety information. If you do not follow the safety instructions and informa- tion on proper handling, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.

5.1 General

The product is not a toy. Keep it out of the reach of children and pets.
Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.
If you have questions which remain unanswered by this information product, contact our technical support service or other technical personnel.
Maintenance, modifications and repairs must only be completed by a technician or an authorised repair centre.

5.2 Handling

Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.

5.3 Installation

Do not place the product under any mechanical stress.
Protect the appliance from extreme temperatures, flammable gases, steam and solvents.
Protect the product from high humidity and moisture.
Protect the product from direct sunlight.
Dust can damage the printer. Do not install the printer in dusty locations.
Vibrations, shock and impacts can damage the printer to move and fall down. Install the printer on a solid, stable and non-slip surface.
Liquids can damage the printer and cause short-circuits. Keep liquids away.

5.4 Operation

The hot printer head can cause burns. Do not touch the printer head.

Static discharge can damage the printer head. Do not touch the printer head.
The cutter blade is sharp and can cause cuts. Do not touch the blade.
Only use recommended label paper to prevent damage to the printer.
Switch off the printer before you make and disconnect connections.
Blocking moving parts can cause damage. Do not touch, block or pull moving parts during operation. Do not stick objects into openings.
Only use approved accessories to prevent damage.
Consult an expert when in doubt about the operation, safety or connection of the product.
If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. DO NOT attempt to repair the product yourself. Safe operation can no longer be guaranteed if the product:
– is visibly damaged,
– is no longer working properly,
– has been stored for extended periods in poor ambient conditions or
– has been subjected to any serious transport-related stresses.

5.5 Connected devices

Also observe the safety and operating instructions of any other devices which are connected to the product.

5.6 Power adapter

Do not modify or repair mains supply components including mains plugs, mains cables, and power supplies. Do not use damaged components. Risk of death by electric shock!

Connect the appliance to a wall socket that can be accessed easily.
As power supply, only use the supplied mains adaptor.
Only connect the power adaptor to a normal mains socket connected to the public supply. Before plugging in the power adaptor, check whether the voltage stated on the power adaptor complies with the voltage of your electricity supplier.
Never connect or disconnect power adaptors if your hands are wet.
Never unplug the power adaptor from the mains socket by pulling on the cable; always use the grips on the plug.
For safety reasons, disconnect the power adaptor from the mains socket during storms.
Do not touch the power adapter if there are any signs of damage, as this may cause a fatal electric shock! Take the following steps:
– Switch off the mains voltage to the socket containing the power adapter (switch off the corresponding circuit breaker or remove the safety fuse, and then switch off the corresponding RCD protective switch).
– Unplug the power adapter from the mains socket.
– Use a new power adapter of the same design. Do not use the damaged adapter again.
Ensure that cables are not pinched, kinked or damaged by sharp edges.
Always lay cables so that nobody can trip over or become entangled in them. This poses a risk of injury.

5.7 Repairs

Repairs require specialist knowledge. Contact a professional to have the printer repaired.
Only use original spare parts to repair the printer.

Getting started

Step 1
Press the cover release tab on either side to unlock the cover. Lift the cover. Step 2
Release and then lift the printing head. If you print multiple labels, align the arrows as indicated in the right graphic below. Step 3
Install the paper roll.

Lift out the spindle.
Adjust the label supply plates on the spindle until the CORE size printed on the spindle matches that of your paper roll.
Slide the paper roll onto the spindle.
Install the spindle in the printer.

Step 4
Guide the label paper and set the label guides.

Release and lift the printing head.
Below the printing head, pass the labels through the label guides.
Adjust the label guides to the label width.

Step 5

Install the ribbon.

Push the spring-loaded ribbon spindle in to release it. Remove the spindle.
Slide the ribbon onto the spindle so that the labels are fed at the front. Observe the diagram printed on the inside of the printer cover.
Install the spindle into the printer.

Step 6
Install the rewind spindle.

Push the spring-loaded rewind spindle in to release it. Remove the spindle.
Slide the empty rewind roll onto the spindle.
Install the spindle into the printer.

Step 7
Link the ribbon to the rewind spindle.

Lift the sticky end of the ribbon and pull the ribbon out just enough to reach the rewind spindle.
Affix the sticky end on the rewind spindle. Observe the diagram printed on the inside of the printer cover.
Wind 3 layers of ribbon onto the empty rewind spindle by rotating the notched wheel.

Step 8
Lock the printing mechanism.

Push down the printing head until it locks.
Close the printer cover and lock it.

Step 9

Connect the printer to the power supply:

Connect the power adaptor cable to the power input socket at the rear of the printer.
Connect the mains cable to the power adaptor.
Connect the power adaptor to a suitable mains socket.

Next steps

Read the operating instructions. Download the operating instructions from www.conrad.com/downloads.
Install necessary drivers and software on your computer. Download software and drivers from www.conrad.com/downloads.

Disposal

This symbol must appear on any electrical and electronic equipment placed on the EU market. This symbol indicates that this device should not be disposed of as unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose of it separately from unsorted municipal waste. Spent batteries and accumulators, which are not enclosed by the WEEE, as well as lamps that can be removed from the WEEE in a non-destructive manner, must be removed by end users from the WEEE in a non-destructive manner before it is handed over to a collection point.

Distributors of electrical and electronic equipment are legally obliged to provide free takeback of waste. Conrad provides the following return options free of charge (more details on our website):

in our Conrad offices
at the Conrad collection points
at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the ElektroG End users are responsible for deleting personal data from the WEEE to be disposed of.

It should be noted that different obligations about the return or recycling of WEEE may apply in countries outside of Germany.

Technical data

8.1 Power adapter
Input ………………………………………. 100 – 240 V/AC, 50/60 Hz, max. 2 A
Output …………………………………….. 24 V/DC, 2.5 A, 60 W
8.2 Environment
Operating temperature ……………… +5 to +40 °C
Operating humidity …………………… 30 – 85 % RH (non-condensing)
Storage temperature …………………. -20 to +50 °C
Storage humidity ………………………. 30 – 85 % RH (non-condensing)
8.3 Others
Dimensions (W x H x D) (approx.) . 285 x 226 x 171 mm
Weight (approx.) ………………………. 2.3 kg

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication reflects the technical status at the time of printing.
Copyright by Conrad Electronic SE.
*2734626_V2_0823_jh_mq_en 27021598713889675-2 I4/O2 en

www.conrad.com/downloads

Documents / Resources

| Conrad RF-TTLP4-01 HT300 Thermal Label Printer [pdf] User Guide
RF-TTLP4-01 HT300 Thermal Label Printer, RF-TTLP4-01 HT300, Thermal Label Printer, Label Printer, Printer
---|---