Conrad HP 63 AL Remote Control Instruction Manual
- June 1, 2024
- CONRAD
Table of Contents
Conrad HP 63 AL Remote Control
Product Information
- Specifications
- Model: HP 63 AL
- Power Source: Two AAA batteries (not included)
- Manufacturer: Transmedia Kabelverbindungen GmbH
- Compliance: Directive 2014/53/EU
Product Usage Instructions
- Installation Precautions
- Never operate the mount without a TV installed.
- Before power connection, ensure that the bracket and the TV are installed correctly.
- Keep children away from power sources.
- Mount Operation
- Upward Movement: Press and hold the button to lift the mount. Ensure there are no obstacles within the range of motion.
- Recall Memory: Press the button to automatically move to the position saved in mem1.
- Memory Setting: Long press the button for 3 seconds to save the current position to memory. Different positions can be saved to mem buttons.
- Lowest Height Limit Setting: Short press the button five times to save the current height as the lowest setting. Resetting the remote control will erase this setting.
- Downward Movement: Press and hold the button to lower the mount. Ensure no obstacles are in the way.
- Recall Memory: Press the button to automatically move to the position saved in mem2.
- Remote Control Operation
- Coding of Remote Control and Control Box: Press the small button on the control box to put it in programming mode. Press SET on the remote control to program it. Clear historical data before pairing a new remote control.
- Default Setting: Short press OK for automatic retraction to the lowest position. Press again to stop.
- Reset Mode: Long press OK for 3 seconds to initiate reset. The system will reset successfully when emitting two beeps.
- EU Declaration of Conformity
- The Motorized Monitor Lift Stand (HP 63 AL) complies with Directive 2014/53/EU. The full declaration is available at Declaration of Conformity
FAQs
- Q: Can I use the HP 63 AL without a TV installed?
- A: No, never operate the mount without a TV installed.
- Q: How do I save different positions to memory?
- A: Long press the button for 3 seconds until you hear a beep to save the current position to memory. Each mem button can store a different position.
PRODUCT FUNCTION
Remote control
Remote control operation instructions
- Coding of Remote Control and Control Box
- STEP 1. When the mount is powered on, press the small button on the control box with a thin tool as shown. The unit will emit a beep, indicating that the control box is on standby for program coding.
- STEP 2. Press the “SET” button on the remote control, and you will hear repeated beeps for approximately 10 seconds indicating that the remote control is being programmed. The unit will emit a beep again indicating success.
- NOTE: Clear up the historical data when replacing a new remote control to pair. Press the small button on the control box with hearing a beep, and hold for 5 seconds to confirm the data-cleaning process is completed until you hear a beep again.
DEFAULT SETTING
- Short press the “OK” button and the mount will automatically retract to the lowest position. To stop it, press the button again.
RESET MODE
- Long press the “OK” button for 3 seconds until you hear a beep, and the mount starts to move downwards.
- Then the mount will move upwards a little bit when reaching the lowest position and automatically come to a stop.
- The system resets successfully when the unit emits two beeps.
CONNECT THE MOUNT TO A NEW DEVICE
- Short press the “mem2” button five times, after each press, you will hear a beep and at the fifth press two beeps, which indicates the mount is disconnecting from the current paired device.
- The disconnection is successful when the unit emits one beep.
- Then follow the Guidebook of Tuya App Installation and Operation to connect the mount to a new device.
- Note: lf the device is failed to search the mount when connecting, follow the above steps or restart the device to re-search the mount.
- Hereby, Transmedia Kabelverbindungen GmbH declares that the Motorized Monitor lift Stand (HP 63 AL) comply with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: https://www.transmedia-germany.com/download.
Never operate the mount without a TV installed!
- Before power connection, be sure that the bracket and the TV are installed correctly.
- Keep the children away from power.
- HP 63 AL is powered by two AAA batteries (not included)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>