LifeSky LS01 Smart Bidet Toilet Heated Tankless Instruction Manual

Instruction manual

LifeSky Smart Toilet-LS01

Smart Toilet

Please read this manual thoroughly before using the product.
Please do not hesitate to contact us if you have any questions in the installation or usage.
Please keep this manual available for future maintenance or reference.

Safety precautions

To prevent damage to the unit and possible injury to users, please follow the safety warnings. Please be sure to carefully read through the user’s manual before installation.
Keep the user’s manual after installation to refer to for troubleshooting advice.

Symbols and meanings

The following symbols are used to indicate important safety precautions when using the product.

| Prohibited.
---|---
| Pay close attention; caution.
WARNING

Prohibited

| Stop using the product immediately if you observe:
Smoke
Unusual sound or odor
Leakage, breakage or other damage
Blocked toilet pan
Continued use under these conditions could cause electrical shock, injury, or water leakage.
Do not clean the smart bidet with heavy chemical cleaning agents such as paint thinner, gasoline, putty powder, nylon brush, etc.
Otherwise, it could trigger a chemical reaction, cause leakage, damage to the product or personal injury.
A loose electrical connection could cause electric shock or a fire.
Do not operate the product or handle the plug with wet hands. This may result in electrical shock or a fire.
Handling the plug during thunderstorms and lightning may cause electrical shock.
Make certain to use the proper voltage. Overloading circuits could overheat and cause a fire.
Do not pour liquids onto the electrical components while it is plugged in as this could result in electrical shock or a fire.
Do not stand or place heavy objects on the product, as it can cause damage.
Do not attempt to disassemble or repair this product yourself. It needs to be taken for professional repair. Otherwise, it may result in damage to the product.
If the electrical plug or line is damaged, unplug the product. Do not attempt to fix the outlet and consult a professional.
Do not block the air openings of the product. Keep the air openings free of lint, hair, and the like.
Do not use while bathing.

Caution

| Make sure the product is installed in a well-ventilated area. Excess humidity and moisture could cause electrical shock or fire.
Disconnect the power supply before removing this product from the toilet to prevent electrical shock or fire.
To prevent electrical shock or fire, disconnect the power supply before cleaning the product and do not apply water directly to it.
Do no expose the product to direct sunlight.
Persons with special health conditions should only use this product with the permission of their doctor. In some instances, supervision or assistance may be necessary when using the product.
Do not use industrial water, wastewater, seawater, reclaimed water and other sewage water. This could cause skin inflammation or other conditions.
Persons (including children) with physical, perceptual, intellectual disabilities or other conditions, need to use the product under the guidance or supervision of someone else, or they may experience electric shock, injury or fire.
All electrical cords and plugs must be waterproof.
The electrical plug must be located more than 0.5m above the floor and away from the bathtub and shower. Otherwise, it could cause electrical shock or a fire.
When replacing an existing bidet toilet seat, remove the old hose assemblies and replace them with the included hose assemblies. Do not reuse the old hose assemblies to avoid safety related problems.
Do not allow children to play with this product. Children must have adult supervision when using the product.
The grounding wire must conform to local codes and must use a three-pronged grounding plug for use.

Components

SMART TOILET

REMOTE CONTROL     REMOTE CONTROL HOLDER

REMOTE EXPANSION SCREW GROUP
(EACH 2 pcs)

DOUBLE-FACED ADHESIVE TAPE

USER’S MANUAL

SEALING RING       INLET VALVE      FLOW RESTRICTOR

Specifications

Rated voltage

| 100-130V~  50/60Hz
---|---
Power cord length|

About 1.5m (59.1 in)

Cleaning

| Water volume| Rear wash| About 0.5L (0.13 gal)-0.7L (0.18 gal)/min

(water pressure 0.2MPa, 3 levels adjustment)

Bidet wash

Swing

| Oscillating cleaning forward and backward
Massage|

Two options: press once for interval cleaning,
press twice for continuous cleaning

Water volume /nozzle position

| 3 levels adjustment
Water temperature range|

About 68°F-107°F (4 levels adjustment)

Safety device

| Temperature limit circuit, thermostat, thermal fuse
Drying| Warm wind temperature|

About 89°F-134°F (3 levels adjustment)

Safety device

| Bimetallic thermostat, thermal fuse
Seat| Surface temperature|

4 levels adjustment, room temperature about 107°F

Safety device

| Thermal fuse
Self-cleaning| Antibacterial seat/nozzle|

Antibacterial material/stainless steel nozzle

Automatic nozzle cleaning

| Self-cleaning
Pre-wetting|

Spray a circle of water after sitting

Deodorization method

| Activated carbon deodorant| Auto open/close lid/seat| Remote control, foot sensing
Toilet| Flush consumption|

4.8 L (1.27 GPF)

Flushing mode

|

Siphon jet

Rough-in

| 305mm (12.0 in)
Rated power| 1100W| Maximum power| 1600W| Waterproof level|

IPX4

Water supply temperature

| 39°F-95°F| Ambient temperature| 37°F-104°F| Net weight| About 37.3kg
(about 82.2 lb)
Dimension| About 680 400 465 mm
(About 26.8 15.7 18.3 in)|

Water supply pressure

| Minimum necessary water pressure:
0.15 MPa (over 20L (5.3 gal)/min when flowing)
Maximum water pressure:
0.75 MPa (static pressure)

1:Rated power: Set the water volume, seat temperature and water temperature to the highest level under the conditions of ambient temperature 68°F±41°F, inlet water static pressure 0.18MPa±0.02MPa, and inlet water temperature 59 F±33 F. Turn on the Inlet function, and test the average power within 60 seconds after the temperature of the outlet water stabilizes.
2:Maximum power: Set the water volume, seat temperature, and water temperature to the highest level under the conditions of an ambient temperature of 73°F+35°F an inlet static pressure of 0.18MPa±0.02MPa, and an inlet temperature of 41°F±33°F. Turn on the bidet function and continue to work stably at the maximum power for a cleaning cycle.
3:Test method of nominal water consumption needs to correctly install the water-saving piece in the accessory kit on the angle valve according to the requirements of the installation instructions, and then perform the test according to the water consumption test standard.(Test the consumption three times for each, in which the pressure of water hose is at a static pressure of 0.24Mpa and 0.55Mpa. Total get six value, the sum is divided by six and the average is the nominal water consumption).

Functions introduction

Washing function

Comfort functions

sensing.
The lid will be automatically close after about 2 mins.
Seat open/close| After toilet lid open, user can open or close the seat by remote control or foot sensing.
LED| LED on or off by light.
Prevent the low temperature scald| To prevent scalding users, the seat temperature will decrease automatically after seated 15mins.

Cleaning function

Anti-bacteria| It’s anti-bacterial treated on the parts which is directly touched by users such as lid and seat.
---|---
Nozzle cleaning| Nozzle will be cleaned when it reach out or pull back.
Water emission| Drain the remain water in the toilet to make water cleaner.
Auto-flushing| Under opening status of lid, user can sit after leaving the seat for a while, the toilet will flush automatically.

New functions

Pre-wetting| After siting, a spray of water will be automatically sprayed inside the bowl to achieve anti-fouling effect.
---|---
Power outage flushing| Connect to the USB TYPE-C with a power bank to achieve the power off flushing.
ECO| Close some functions and enter energy-saving mode.
Personal setting| You can store your preferred wand position, water temp, flow and dry temp settings.
Foot sensing induction| Touch the sensing area with foot and then lid opens automatically.
Touch the sensing area with foot and then seat opens automatically.
Touch the sensing area with foot and then toilet flush automatically.

Parts name

1. Lid

2. Seat

3. Rear wash hole

4. Bidet wash hole

5. Drying baffle

6. Nozzle baffle

7. Nozzle

8. Ceramic toilet

9. Foot sensing

10. Knob

11. Power-off flush connector

12. Power indicator

13. Seat temp status indicator

14. Flushing status indicator

15. Seat temp indicator

16. Water temp indicator

Product drawings

1. About 680mm (26.8 in)
2. About 400mm (15.7 in)
3. About 465mm (18.3 in)

Power and water connection tip

1. Connect to grounded outlet
2. Caution electric shock!
3. GFCI outlet

If the power cord is not long enough, please do not use a extension cord.
Only for reference. Bathroom sizes and configurations may vary.

Installation precaution

(1) Don’t install our product in the room with more than 90%RH humidity (relative humidity).
It is suggested to separate dry space from moist one, such as installing shower rooms or shower curtains.
(2) Only the specified power supply can be used. (Other power sources may cause product failure or damage).
(3) Please do not supply water or power before finishing installation.
(4) Please use wires and waterproof sockets suitable for the power of this product.
(5) Please install the waterproof socket at a suitable height on the wall.
(6)The water-supplying pressure should be 1.5kgf/cm²~7.5kgf/cm²(0.15MPa~0.75MPa).
The toilet cannot reach full cleaning functionality if the water pressure cannot reach 0.15MPa.
(7)The water-supplying temperature should be 39.2°F-95°F.

Notice:
Please remove the dirty water from the pipe before installation. Residual sediment and other debris may jam in the pipeline if it is the newly decorated house, which may cause damage to the machine and affect the health of the human body.

Installation Tools

Percussion Drill     Glue gun     Tape    Adjustable Wrench         Pliers

Gradienter       Steel saw      Knife       Screwdriver        pencil

Product installation

1. Install the water inlet valve

Clean the ground and dry the water before installation. Mark the central lines of the draining outlet, and install the inlet valve on the wall.

1. Connect to grounded outlet
2. Caution electric shock!
3. GFCI outlet

4. 500mm (19.7 in)

5. 150mm(5.9 in)
6. 300mm(11.8 in)
7. 305mm(12.0 in)
8. Drain outlet
9. center mark line

2. Mark the curve of ceramics

Align the drain hole of ceramic with the central line. Mark the curve of ceramics for later installation.
Glass cement application: Glue the outline with glass cement to install the toilet.

1. wall
2. 305mm(12.0in)

3.Toilet installation(Method 1)

(1) Sealing ring installation

Gently tilt the toilet sideways until it rests on the side surface.
Install the sealing ring evenly along the outlet, and the small end of the sealing ring facing the toilet.
Glue the edge of toilet bottom with glass cement, place the toilet base along the outline and position the toilet base.

1. Sealing ring
2. Draining hose

(2) Toilet (ceramic) installation

Lift the toilet, take the floor drain as a reference, align the ceramic body of the toilet with the ceramic contour line drawn on the ground, and slowly put the ceramic on the ground so that the two marks overlap. After overlapping, press the ceramic down (can be pressed by the weight of the human body) so that the sealing ring fully contacts the ground.
Do not move the ceramic or shake it left and right after the marks are overlapped, otherwise the seal produced by the sealing ring may be damaged and cause water leakage.

4.Toilet installation(Method 2)

(1) Remove the bidet seat

Remove the fixing screws of the toilet; remove the connecting pipes and wires of the toilet, separate the bidet seat from the toilet.

1. Decoration panel
2. Screw
3. Washer
4. Fixed hole

(2) Sealing ring installation

Place the sealing ring on to the flange.

1. Sealing ring
2. Flange

(3) Ceramic installation

Glue the edge of toilet bottom with glass cement.
Line up the toilet base over the flange screws.
Place the toilet base and secure the flange bolts.
Glue the edge of toilet bottom with glass cement, place the toilet base along the outline and position the toilet base.

(4) Bidet seat installation

Attach the connecting pipes and wires of the toilet, adjust the bidet seat to match the toilet, use the screws to fix the bidet seat on the toilet.
Pay attention to the tightness of the pipes connection.

5. Connection of water inlet valve

Connect the water inlet braided pipe to the water inlet angle valve; if the water pressure is high, you can install a flow restrictor or adjust the position of the angle valve to achieve the best flushing effect.

NOTE:
Clean the floor and tools, do not use the toilet immediately, it takes 48 hours to cure and keep the toilet dry.

1. Inlet angle valve
2. Fow restrictor
3. NOTE:
   If the water pressure is less than 0.24Mpa (static pressure), remove the flow restrictor.

6.Connect to power

Connect the electricity plug with protection unit. Press the power switch, the light turns on, power is on, and hear the buzzer calls.

7.Using the product for the first time (Check every function button of

the remote control, manual flushing and side button function is normal.)

(1) Open the water supply valve, connect to the power plug.
Check that every function of product is normal, such as rear/bidet wash, dry, flow adjustment, water temp adjustment, massage cleaning, swing cleaning, LED, seat heated adjustment, etc.
(2) Rear/bidet wash performance test.
Press the seat sensor with hand to check if the nozzle works or not.

Notes: Open the water supply valve and connect to the power plug. When using the product for the first time, press the rear/bidet wash button in the remote control or knob. If the toilet doesn’t work, it may be lack of water or seat sensor blocked.

Instructions for remote control Installation

Method 1:

(1) Install the remote control fixing panel with a magnet on the remote control fixed seat and lock tightly.
Note: Pay attention to the polarity when installing the magnet Place the larger side of the magnet hole outside the fixed panel and enclose the small hole surface inside the fixed panel, as shown in the below figure 1.
(2) Put the double sided tape on the remote control fixed seat.
(3) Clean dust, grease, water droplets on the walls and wipe them clean.
(4) Press the remote control fixed seat with double sided tape on it. Press it evenly for 3 to 5 minutes.
Attach the remote control fixed seat to the wall.
Note: The method is applicable to glazed tiles, glass and smooth wall.

Figure 1

1. Magnet
2. Double sided tape

Method 2:

(1) Drill a hole of 78mm(3.07 in)-82mm(3.23 in) length and 22mm(0.87 in) depth on the wall by the drill with the diameter of 6mm(0.24 in).
Note: the position of the hole shall be satisfied for user to get the remote control conveniently when sitting on the seat.
(2) After installing, the expansion plug in the wall shall align the fixing hole of the remote control and then lock the bolt. Install the remote control fixing panel with a magnet on the remote control fixed seat and lock tightly.
Note: pay attention to the polarity when installing the magnet. Place the larger side of the magnet hole outside. The fixed panel and enclose the small hole surface inside the fixed panel; as shown in the below figure 2.

Figure 2

1. 82mm(3.07 in)
2. 78mm(3.23 in)
3. Magnet

Put the remote control on the fixed base after installing the battery, and the remote control can automatically absorb on the fixed base.

NOTE:
Please place the remote control on the fixed place if not use. (To avoid the remote control falling down)
 It may cause damage if the remote control falls down.
 Please do not spill water on the remote control or drop into the water, or it may cause damage.

Remote control panel overview

1. Signal light
2. Stop
3. Bidet
4. Flush
5. Plus
6. Water temp
7. Nozzle position
8. Massage
9. Swing
10. User 1
11. User 2
12. Lid open/close
13. Seat open/close
14. ECO
15. Dry
16. Seat temp
17. Flow
18. Minus
19. Rear
20. Signal window

Remote control alignment: After the product is connected to the power supply, the remote control alignment operation can be carried out within 1 minute from the buzzer call.

At the same time, press the “User 1” and “User 2” buttons on the remote control. After 3 seconds, the “rear wash/bidet wash/stop” three buttons flicker at the same time, press the “plus” to increase. Select the required level, press the “stop” button, buzzer calls, then the code is successful, then the remote control can only control the product; buzzer calls two times, represents code failure;

If you want to cancel the alignment, press the “User 1” and “User 2” buttons on the remote control at the same time. After 3 seconds, the “rear wash/bidet wash/stop” buttons flicker at the same time. You can cancel the code by pressing the stop key directly.

Using instructions

STOP

Press the button, all functions off.

REAR

Press the button, rear spray function turns on, auto off after 2 mins or off by pressing the stop button.
Function will stop if user leaves

BIDET

Press the button, bidet/front spray function turns on, auto off after 2 m ins or off by pressing the stop button.
Function will stop if user leaves.

FLOW ADJUSTMENT

Under rear/bidet wash mode, the water flow is settled on normal level( initial level is in the medium ).
Press “FLOW button to start the flow adjustment, and press plus button to increase flow, press minus button to decrease flow. Total 5 levels, and corresponding indicator will on under different level.

WATER TEMP SETTING

Under rear/bidet wash mode, initial level is in the medium.
Press “TEMP” button to start the water temp, and press plus button to increase water temp, press minus button to decrease water temp, total 3 levels, and corresponding indicator will on under different level.

NOZZLE POSITION ADJUSTMENT

Under rear/bidet wash mode, initial level is in the medium.
Press “POSITION” button to start the position adjustment, and press plus button to forward the nozzle position, press minus button to backward the nozzle position.
Total 3 levels, and corresponding indicator will on under different level.

SEAT TEMP ADJUSTMENT

Seat heated after sitting, heat preservation after reaching the set temp. The initial level is in the medium Press “SEAT ‘ button to start the seat temp, and press plus button to increase the seat temperature press minus button to decrease the seat temperature.
Total 3 levels(including neutral), and corresponding indicator will on under different level.

MASSAGE

During rear/bidet wash mode, press the “Massage” button, function will start after a beep.

1. Interval massage mode: The nozzle sprays with varying pressure.
2. Powerful massage mode: The nozzle sprays pressurized water.

Remark:
The Massage cycle order is interval massage > powerful massage > regular cleaning.

SWING

During rear/bidet wash mode, press the “Swing” button function will start after a beep.
During swing function, the nozzle will oscillate back and forth. Press the “Swing” button again to stop swing function. Pressing the “Stop” button will stop all cleaning functions.

FLUSH

Press “flush” button to activate flushing.

DRY

Press the button, drying function turns on.(Initial level is in the medium. Press plus button to increase warm dry temp Press minus button to decrease warm dry temp, total 5 levels, and corresponding indicator will on under different level) Auto off after 2 mins or off by pressing the stop button.
Function will stop if user leaves

PERSONAL SETTING USER1/PERSONAL SETTING USER 2

Under rear/bidet wash mode you can set your preferred water temp, wand position, flow and warm dry temp. While cleaning is in progress, set your preferred water temp, flow, wand position and warm dry temp, and then press and ho d (User1) or (User2) for 2 seconds or longer. After (User1) or (User2) is pressed, please push the button used for rear/bidet wash.

ECO

Press the button to enter energy saving mode.
Under energy saving mode, seat temperature is low(level 1) to achieve energy saving; only the power indicator light on the display is on, others are off.
Remark:
Energy saving mode will be suspended and goes to function mode if someone uses the seat in the middle of energy saving.
Seat temperature returns to the level which is settled, the display lights up normally.
The energy saving mode is restored after the human body leaves the seat.

LID OPEN/CLOSE

When lid open/close, press the button, lid automatically turn off/turn on.

SEAT OPEN/CLOSE

When seat open/close, press the button, seat automatically turn off/turn on.
When lid close, press the button, the inductor sense that the lid is closing.
The program automatically open the lid, and then opening the seat automatically.

COMBINATION FUNCTION KEYS

Stop + Rear wash: Long press for 5 seconds to activate or deactivate the powerful deodorizing function.
Stop + Bidet wash: Long press for 5 seconds to activate or deactivate the night light function.
Stop + Massage: Long press for 5 seconds to activate or deactivate the foot sensing function.
Flush + Rear wash: Long press for 5 seconds to activate or deactivate the pre- wetting.
Rear wash + Bidet wash. Long press for 5 seconds to activate or deactivate the automatic nozzle cleaning.

Knob function description

Knob function description
No need to reset the stepless knob after use

1. Backward
2. Press
3. Forward

■ Sitting

• Bidet wash: Knob forward, spray bar extend, bidet wash works about 2 minutes.

• Rear wash: Knob backward, spray bar extend, rear wash works about 2 minutes.

• Nozzle position. Under bidet/rear wash, knob forward or backward to adjust nozzle position.

• Stop: Under bidet/rear wash, press the knob to stop current working function.

• Drying: Without any function working, long press the knob fort seconds to start drying;
  Knob forward to make the wind temp higher, knob backward to make the wind temp lower.

• Flush: Without any function working, press the knob to flush.

■ Not sitting

• Press the knob to flush.
• Long press the knob for 5 seconds to start or close the knob indicator.

■ Foot sensing

• When the lid and seat are closed, short touch the sensing area with foot and the lid automatically opens.
  when the lid and seat are closed, long touch the sensing area with foot and the lid and seat automatically open;
  When the lid open, seat closed, short touch the sensing area with foot and the seat automatically opens;
  When the lid and seat are open, short touch the sensing area with foot to realize the flushing function.

Cleaning

Maintenance and cleaning of lid and seat.

1. Disconnect the power, turn off tee valve.

2. In case of using a mixture of washing agent and water as well as any available solution for seat cleaning, use soft and wet sponge or cloth to clean the seat. Use a soft towel to make the seat dry, or let it dry naturally.
   The product is an electric appliance. Be careful not to allow water to get inside or leave detergent in the gap between the top unit and the bowl unit. Doing so could damage or malfunction.
   Avoid using materials that will damage the surface-clean the surface with a soft and wet sponge or cotton cloth, instead of materials that can damage the surface.
   Corrosive chemicals or cosmetics (such as cleaners containing abrasive compounds and aftershave) should not come in contact with the seat as this will damage the surface.

3. Connect the power, turn off tee valve.

Maintenance and cleaning of the bowl.

1. Disconnect the power.

2. The bowl unit can be cleaned with a toilet brush, toilet detergent or a similar tool.
   Corrosive chemicals (such as cleaners containing abrasive compounds and strongly acidic cleaners or strong alkaline cleaners) should not wash the bowl as this will damage the surface of bowl.
   Wire brush and abrasive nylon scrubbing brush should not wash the bowl as this will damage the surface of bowl.
   Do not use any water repellant, stain-proofing cleaner or surface coating agent.

3. Connect the power.
   Notice: If the bowl unit is clogged, use commercially available tools that are made for un clogging toilet.

Cleaning the water filter

(1) Unplug the product. Shutoff water supply.

(2) Remove the water-inflow filter from the inlet hose.
(3) Take out the filter by using a flat-blade screwdriver to unscrew the filter.

(4) Remove the filter screen and rinse it with clean water.
(5)  Install the filter screen as it is, be sure to tighten it, otherwise it will cause water leakage.

Measures for special cases

When the toilet can’t be flushed automatically due to power interruption.

USB TPYE-C

When the power is off, connect to the USB TPYE-C with a power bank to achieve the power off flushing.

When the toilet can’t be flushed automatically due to water interruption.

(1) Flush away the sewage in the toilet by a special basin for taking in water.
(2) After water flushing, water level is lowered and water is added to avoid stink.

Notice:
When the toilet can’t be flushed automatically due to water interruption.
After long term idle condition, make sure to wash it for several times and the inner pipelines are cleaned before use.

Maintenance in case of long-term idle status

(1) Disconnect the power plug, and turn off the tee valve, unscrew inlet hose. Exhaust the water inside inlet hose.
(2) Press the release button of the product, exhaust the water inside the toilet

Trouble shooting

Phenomenon

| Reasons|

Measures

---|---|---
The product out of work| Whether the power supply is plugged in.| Insert the plug or detect the power socket.
Power failure.| Wait until the power is restored.
The leakage protector is disconnected.| Insert the plug the power socket, press reset button on the plug.
Rear cleaning

Bidet cleaning

Dry

The toilet does not flush even when the button is pressed.

| The wand extends but water does not come out.

The cleaning water pressure is weak.

| Has a water failure occurred? Press the “stop” button and wait until the water failure is over.
Is the water supply valve close ?
turn on the tee valve.
Is the water filter drain valve clogged with foreign matter? Clean or replace the filter.
Low water temperature setting| Use the water temperature keys on the remote control to adjust the cleaning water temperature.
The seat sensor may have difficulty detecting some sitting posture.| Sit back on the toilet seat.
The nozzle stops cleaning suddenly.| If the user moves too fast or leaves the seat, the seat sensor cannot detect in short time.| Sit back on the seat sensor detection position, then start the relevant button.
Low water pressure when rear/bidet wash.| Filtration screen of inlet angle valve may be blocked| Clean or replace the filter.
The water-inflow hose may leakage| Check the hose and tighten it.
Deodorization effect is not obvious.| The seat sensor does not sense someone sitting (no deodorizing sound)| Sit back on the seat sensor detection position.
Activated carbon Titer block or spacer may be blocked.| Remove the deodorizing window to clean or replace the activated carbon filter.
Deodorant function continues to work after user leaves.| The deodorant function will be continue to work for 20 seconds in order to remove the residual odor after the use leaves.| It’s common phenomenon.
Water comes out unexpectedly from the wand.| Abnormal operation| Disconnect the power plug and wait about 1 minutes before inserting it again.
Water comes out unexpectedly from the inlet hose.| the inlet hose may damage| Replace the inlet hose.
The toilet seat does not get warm.| The seat sensor may have difficulty detecting some sitting postures.| Sit back on the toilet seat.
The toilet seat temperature set a low level.| Use the remote control to adjust seat temperature.
The dry temperature is not enough.| Lower dry temperature is set.| Use the remote control to adjust dry temperature.
The toilet does not flush when the button is pressed.| Water is not available from the water supply.| Use a bucket full of water to flush.
The water supply valve is not fully open.| Check the tee valve.
Waste material does not flush down completely.| The water supply valve is not fully open.| Check the tee valve.
The water filter is clogged.| Clean the filter.
The water supply to the toilet may disrupted by other running water fixtures.| Cease using other fixtures and then flush the toilet.
Flushing may be difficult due to the consistency of the waste material.| Flush the toilet cleaned with with a brush again. If the bowl is not a flushing remove the stains or similar instrument.
There is residue on the bowl unit surface.| Oil and other hard-to -see grime may stick to the bowl unit surface.| Clean the bowl with a non-abrasive toilet detergent.
The toilet does not flush when water pressure is normal.| Flushing valve failure.| Please professional maintenance personnel should be checked and maintained.
The remote control fail to control the toilet.| Lower battery| Replace with new batteries.
Battery polarities are mounted reversely.| Reinstall properly.
The remote control is too far from the toilet.| Get close to the toilet.
The remote control transmitter or the top unit receiver may be blocked.| Remove obstructions, dirt, water droplets or any other blockages.

LED.

| The indoor light is too bright.| Please turn off the indoor light and close the curtain.
The top unit is unstable.| There cushion is clearance between the toilet seat and the bowl.| It’s common phenomenon.
Water is leaking from the plumbing connections| nuts in a connection are loose.| Tighten them with a tool such as monkey wrench.
The water leak does not stop.| Close the water supply valve and seek repair.
A strange sound tis emitted from the top unit.| when user sit on the toilet seat, the seat switch turns on.a click sound is heard.| It’ s common phenomenon.

Notice:
If you are in trouble, please read the above troubleshooting and repair the product according to the instruction of the solution. If the problem is not in the common troubleshooting, please contact the professionals, dealers, or call the national unified service hotline to ask for help.

Please note that there will be no any notification if any changes to this product and also accessories.
There may be differences between contents and material objects, please subject to the latter one.

Maintenance Service Sheet

Product| | Product code|
---|---|---|---
The selling store| | Purchase date|
Province             City| Dealer ( signature ):
Maintenance content|
Free maintain regulation:

1. Free maintenance is provided when you use it properly in accordance with instructions and under warranty.

2. Please contact the dealer or the company if the fault occurs under warranty.

3. The following situations is chargeable for maintenance under warranty:
   (1) Faults or damages caused by the improper operation, repair or reinstall.
   (2) Faults or damages caused by forced movement after the product is installed.
   (3) Faults or damages caused by earthquakes, fires, floods, lightning strikes, corrosive liquids, abnormal voltages and other natural disasters.
   (4) Faults or damages caused by other approaches which are not for family-use.
   (5) Fail to provide the maintenance-service sheet.
   (6) There is no detailed records or there are modified records on the maintenance-service sheet.

4. This maintenance-service sheet is valid.

5. This maintenance-service sheet is unrepeatable, please safe keep it.

6. The customer can go to the local repair network or sent the products back to the company for free repair within two years from the purchase date.

Executive standard: CONFORMS TO UL STD. 1431/UL STD. 1591 ASME A112.4.2-2021
Warranty period: within two years from the purchase date

■ Due to the constant improvement about our products, we will keep the final interpretation of products change.
■ If the products you bought exist differences from the instruction, please in kind prevail.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
■ Consult the dealer or an experienced radio/TV technician for help.

Made in China
52211772-01 V1.0

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>