PATON STANDARD-350-400V MMA Welder Machine User Manual
- June 17, 2024
- PATON
Table of Contents
STANDARD-350-400V MMA Welder Machine
User Manual
ATTENTION!!! Before using the equipment, we recommend you to read the extended version of the operating manual by the link: https://paton.ua/files/passports/Standard_GEN.pdf
https://paton.ua/files/passports/Standard_GEN.pdf
Purchase date ”……………20………………..
Vendor signature
| The welding machine is manufactured in accordance with technical standards
and established safety rules. However, incorrect handling results in the
following dangers:
– injury of maintenance personnel or third persons;
– damage of the machine or property of the enterprise;
– derangement of efficient working process.
---|---
All persons dealing with start‐up, operation, attendance and maintenance of
the machine must:
– undergo relevant qualifying examination;
– have knowledge about welding;
– carefully follow these instructions.
Malfunctions that can reduce safety must be eliminated immediately.
SAFETY RULES
| DANGER OF MAINS AND ARC CURRENT
– electric shock can lead to death;
– magnetic fields created by this machine can have adverse effect on
operability of electrical appliances (such as cardiac pacemakers). People who
use such appliances shall consult with a doctor before approaching the
operating welding area;
– welding cable must be robust, intact and insulated. Loose connections and
damaged cables must be immediately replaced. Mains cables and cables of the
welding machine must be checked for insulation integrity by an electrical
engineer on a regular basis;
– when using the machine, never remove its outer case.
---|---
| DANGER OF WELDING ARC RADIATION
It is forbidden to observe the welding arc with the naked eye. The arc and
splashing generated during operation can burn the skin or cause a flame,
therefore a protective mask with a tinted filter should always be worn
(goggles must be equipped with goggles with a DIN 9 10 filter). Unauthorized
persons in the operating area of the device must protect their eyes with
special goggles or use non-flammable, radiation-absorbing screens.
| DANGER OF HAZARDOUS GASES AND VAPOURS
– if smoke and hazardous gases emerge in the operating zone, remove them with
special means;
– provide sufficient fresh air inflow;
– arc radiation field must be free from solvent vapours.
| DANGER OF MAGNETIC FIELD
Magnetic fields created by this machine can have adverse effect on operability
of electrical appliances (such as cardiac pacemakers). People who use such
appliances shall consult with a doctor before approaching the operating
welding area.
| DANGER OF SPARKING
– remove flammable objects from the operating zone;
– it is not allowed to weld vessels where gases, fuel or oil products are
stored or used to be stored. Residues of these products may explode;
– when working in fire‐dangerous or explosion‐dangerous rooms, adhere to
special rules in compliance with national and international regulations.
| INDIVIDUAL PROTECTIVE EQUIPMENT
To ensure individual protection, adhere to the following rules:
– wear robust footwear, which retains insulating properties in moist
conditions as well;
– protect the hands with insulating gloves;
– protect the eyes with a headshield, with is equipped with a black‐light
filter complying with safety standards;
– wear only proper low‐flammable clothes.
| DANGER OF INTENSE NOISE
The arc generated during welding can emit sounds above 85 dB during 8 hours of
working time. Welders working with the equipment wear ear protection during
work.
UNPACKAGING
The delivery set of the device includes:
CONTROL ELEMENTS AND
INDICATION
-
Arc current controller, allows for smooth adjustment of arc current.
-
Machine operation indicator:
a) green light – normal status of the device;
b) permanent yellow light – the device is overheated. -
Mains breaker.
-
Power supply cable.
А – Power current socket “+” of bayonet type:
B – Power current socket “‐” of bayonet type:
START-UP
The welding machine is designed solely for manual arc welding with a stick
electrode. Other use of the machine is considered undue. The manufacturer is
not responsible for damage cause by undue use of the machine. Intended use of
the machine implies adherence to instructions of this operating manual.
INSTALLATION REQUIREMENTS
The machine must be placed so as to ensure free inlet and outlet of cooling
air through vent holes on the front and the rear panels. Take care that metal
dust (for example, during emery grinding) does drawn directly into the machine
by the cooling fan.
POWER CONNECTION
The welding machine of series design is rated for three-phase mains voltage is
3x380V or 3x400V, three wires are dedicated for this. Safety rules when
working with welding equipment require grounding of the unit housing. There
are two ways to do this: 1) by using the fourth wire in the mains yellow-green
cable (international marking standard); 2) by using a bolted terminal on the
rear wall of the unit (a stricter grounding standard, used in the CIS
countries).
CAUTION! When the unit is connected to a mains voltage higher than 450V,
all manufacturer’s warranty obligations become invalid!
The manufacturer’s warranty obligations also become invalid in case of an
erroneous connection of the mains phase to the sour ce ground.
Mains connector, cross‐sections of power supply cables and supply‐line fuses
must be selected on the basis of technical specifications of the machine.
Used electrode| Set current value| Cross-section of each core of
the mains wire, sq. mm| Maximum wire length, m
---|---|---|---
3 x 38o/400V – Standard-350-400V
03 mm| not more than iaoA| 1,5| 135
2| 175
2,5| 220
4| 350
6| 525
04 mm| not more than 16oA| 2| 130
2,5| 160
4| 26o
6| 385
05 mm| not more than 22oA| 2,5| 115
4| 18o
6| 270
06 mm
Fusible| not more than 27oA| 2,5| 85
4| 135
6| zos
06 mm| up to 35oA| 2,5| 65
4| 100
6| 150
Machine connection diagram for welding with stick electrodes
Recommended length
of power welding cables during welding:
Maximum current| Cable length, m (one way)| Cross-section
area, sq. mm| Cable brand
---|---|---|---
not more than 160А| 2 … 7 m| 16 mm²| KG 1х16
not more than 200А| 3 … 9 m| 25 mm ²| KG 1х25
not more than 250А| 5 … 11 m| 35 mm ²| KG 1х35
not more than 270А| 5 … 11 m| 35 mm²| KG 1х35
up to 350А| 6 … 14 m| 35 mm²| KG 1х35
TECHNICAL PARAMETERS
| PARAMETERS | Standard-350-400V |
|---|---|
| Rated supply voltage soHz, V 3×380 | 3×400 |
| Supply voltage variation limits, V | ±15% |
| Rated current consumption from the mains phase, A | 17,7 |
| Rated welding current, A | 35o |
| Maximum operating current, A | 450 |
| Load duration (LD) | 7o%/at 350A |
1oo%/at 29oA
Limits of regulation of welding current, A| 50 —350
“Hot-Start” function| Automatic
“Arc Force” function| Automatic
“Anti-Stick” function| Automatic
No-load voltage, V| up to 8o
Arc striking voltage, V| no
Rated power consumption, kVA| 11,7
Maximum power consumption, kVA| 15,2
Efficiency, %| 90
Cooling| Forced
Operating temperature range| —25 … +450C
Overall dimensions (length, width, height), mm:| 390 x 145 x 335
Weight without accessories, kg| g,8
Protection rating| IP33
WARRANTY
Dear customer!
PATON INTERNATIONAL thanks you for choosing PATON™ products and guarantees
high quality and flawless functioning of this product, subject to the rules of
its operation.
ATTENTION!!! Before using the equipment, we recommend that you read the
operating instructions, and also check the correctness of filling out the
warranty card: the model name of the product you purchased, as well as the
serial number must be identical to the entry in the warranty card. It is not
allowed to make any changes and corrections to the coupon.
WARRANTY POLICY
PATON INTERNATIONAL guarantees the correct operation of the power source
provided that the consumer observes the conditions of operation, storage and
transportation.
ATTENTION! There is no free warranty service in case of mechanical damage to
the welding machine! The main warranty period for welding equipment is:
| DEVICE MODEL | WARRANTY PERIOD |
|---|---|
| Standard-350-400V | 3 years |
The main warranty period starts from the date the inverter equipment is sold
to the end customer.
During the main warranty period, the seller undertakes, free of charge for the
owner of PATON™ inverter equipment:
- make diagnostics and identify the cause of the breakdown;
- to provide units and elements necessary for the repair;
- to carry out work to replace the failed elements and assemblies;
- to test the repaired equipment.
The main warranty obligations do not apply to the equipment:
- with mechanical damage that affected the performance of the device (deformation of the case and parts as a result of falling from a height or falling on the equipment of heavy objects, falling out of buttons and connectors);
- with traces of corrosion, which caused a malfunction;
- out of order due to exposure to its power and electronic elements of abundant moisture;
- failed due to the accumulation of conductive dust inside (coal dust, metal shavings, etc.);
- in case of an attempt to independently repair its components and / or replace electronic elements;
- this equipment, depending on the operating conditions, is recommended once every six months, in order to avoid the breakdown of the device, to clean the internal elements and assemblies with compressed air, remove the protective cover. Cleaning should be done carefully, keeping the compressor hose at a sufficient distance to avoid damage to the soldering of the electronic components and mechanical parts.
Also, the main warranty obligations do not apply to out-of-order external elements of equipment subject to physical contact, and related / consumables, claims for which are accepted no later than two weeks after the sale:
- on and off button;
- knobs for adjusting welding parameters;
- connectors for connecting cables and sleeves;
- control connectors;
- mains cable and mains cable plug;
- carrying handle, shoulder strap, case, box;
- electrode holder, ground terminal, torch, welding cables and sleeves.
The seller reserves the right to refuse to provide warranty repairs, or to set the month and year of manufacture of the device as the start date for the fulfillment of warranty obligations (established by the serial number):
- if the owner loses the warranty card;
- in the absence of correct or even any kind of filling in the passport by the seller when selling the device.
The warranty period is extended for the period of warranty service of the
device in the service center.
You can find out information about the nearest service center at the place of
purchase.
Date of receipt for repair…………….., 20………………….
signature
Symptoms of non‐operability:
Cause:…………
Date of receipt for repair…………., 20………………
signature
Symptoms of non‐operability
Cause:……………..
Date of receipt for repair ……………….”, 20…………………
signature
Symptoms of non‐operability:
Cause:…………
Date of receipt for repair……………..”, 20…………………
signature
Symptoms of non‐operability:
Cause:…………….
signature
Symptoms of non‐operability:
Cause:……….
Date of receipt for repair………….”, 20………………..
signature
Symptoms of non‐operability:
Cause: ………………
PATON Standard DC MMA
Documents / Resources
|
PATON STANDARD-350-400V MMA Welder
Machine
[pdf] User Manual
STANDARD-350-400V MMA Welder Machine, STANDARD-350-400V, MMA Welder Machine,
Welder Machine, Machine
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>