Breezary 29007-SN Ceiling Fan with Light User Manual

Breezary 29007-SN Ceiling Fan with Light User Manual

Safety Information

READ AND SAVE THESE INSTRUCTIONS.

1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before you begin.
2. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
3. The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 Ibs (15.9 kg). Use only UL Listed outlet boxes marked “Acceptable for Fan Support of 35 Ibs. (15.9 kg) or less.”
4. Do not place objects in the path of the blades.
5. To clean the fixture, turn off the power, wait for it to cool, and wipe the fixture with a clean, soft cloth.
6. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipmentgrounding conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.
7. All setscrews must be checked and retightened where necessary before installation.

WARNING : To reduce the risk of electrical shock or fire,not use this fan with any solid-state fan speed control device. It will permanently damage the electronic circuiry.

WARNING : To reduce the risk of personal injury, do not bend the blade brackets when installing the rackets| balancing the blades, or cleaning the fan. Do not insert, foreign objects in between rotating fan blades.

WARNING : To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked “acceptable for fan support of 35 Ibs. (15.9Kg) or less” A and use screws provided with the outlet box.

WARNING : To avoid possible electrical shock, turn  the electricity off at the main fuse box before wiring.

WARNING : To reduce the risk of electrical shock, this must be installed with an isolating wall control/switch.

CAUTION : To reduce the risk of personal injury, use only the screws provided with the outlet box.

CAUTION : Please use carefully when working around or cleaning the fan to avoid injury or damage of fan.

CAUTION : The fan must be mounted with a minimum of 7 ft (2. 1 m) clearance from the trailing edge of the blades to the floor.

CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Dimension Reference

Hardware Included

Hardware Package      Quantity

S1. Blade Screw 16

S2. Machine Screw 2

S3. Machine Screw 2

S4. Wood Screw 2

S5. Wire Nut 3

S6. J-hook 1

S7. Lock Washer 4

S8. Star Washer 2

S9. Washer 4

S10.Paper Washer 16

S11.Lock Washer 4

S12. Washer 4

S13.Screw 1

S14.Balance Kit   1

Fan Parts Included     Quantity

1. Mounting Bracket 1
   

2. Donwood  2
   

3. Canopy  1
   

4. Canopy Cover  1
   

5. Yoke Cover  1
   

6. Motor Assembly  1
   

7. Light Kit   1
   

8. Lampshade   1
   

9. Remote Control (Batteries not included)  1
   

10. Blade      1
    
    

Exploded View

Installation Instructions

Step1 MOUNTING

• Take out fan motor housing.
• Remove cotter pin and bolt from yoke.
• Loosen jam screw in yoke until it is flush with the inside surface.
• Take out dowered, canopy and yoke cover.
• Place dowered inside canopy and yoke cover.
• Route wires exiting motor through yoke cover, canopy and dowered.
• Insert bolt through hole in and dowered. Be careful not to damage or cut the fan wires.
• Tighten bolt. Secure with cotter pin through hole in the end of the bolt.
• Secure dowered in position by tightening jam screws. Slide yoke cover down and it will flush with the motor housing

CAUTION : To ensure wobble – free operation and to avoid damage to the fan, the dowered and the set screws must be completely tightened

Step2 MOUNTING BLADES TO MOTOR

• Insert the blade into the fan as shown.
• Tighten the blade to motor with the screw and lock washer as shown
• Slightly turn the blade after installation and repeat the same step for the other blades.
  

Step3 LIGHT KIT

WARNING : BE SURE TO TURN OFF POWER BEFORE INSTALLING.

• Remove light kit screws.
• Connect polarized connectors of light kit to corresponding connectors found in switch housing.
• (connect WHITE light kit unit wire to WHITE fan wire, connect BLUE light kit unit wire to BLUE fan wire)
• Carefully tuck electrical wires back into switch housing, align light kit with switch housing and secure with three light kit screws.
• Place diffuser onto the fan and turn to secure.

Step4 MOUNTING BRACKET TO MOTOR

WARNING : To reduce the risk of fire, electric shock, or personal injury, mount to UL/CSA
listed outlet box marked acceptable for fan support and use mounting screws provided
with the outlet box.

• Install J-Hook through center of outlet box to the wood joist.
• Secure mounting bracket and rubber gaskets to the metal outlet box.
• Hang the safety cable onto the J-hook.

Step5 ELECTRICAL HOOK-UP

A. Make the following wire connections using the wire nuts supplied.
a To the household supply wires

• -Connect the following 4 GREEN wires to the GREEN supply wire.
  1. GREEN wire from the dowered
  2. GREEN wire from the receiver
  3. GREEN wire from the motor
  4. GREEN wire from the mounting bracket
• Connect BLACK receiver wire to BLACK supply wire.
• Connect WHITE receiver wire to WHITE supply wire.

b To the light wires

• Connect WHITE receiver wire to the WHITE wire from motor.
• Connect BLUE receiver wire to the BLUE wire from motor.

¢ To the fan wires

• Connect ORANGE receiver wire to the ORANGE wire from motor.

• Connect PINK receiver wire to the PINK wire from motor.

• Connect RED receiver wire to the RED wire from motor.

• After making the wire connections, ensure the wires should be separated with the grounded
  conductor and the equipment-grounding conductor on one side of the outlet box and the
  ungrounded conductor on the other side of the outlet box.

• Ensure the splices after being made should be turned upward and pushed carefully up into the outlet box.

• Make sure no bare wire is visible at the wire nuts.
  
  NOTE : Once ground wires are connected, carefully tuck all wires and wire nuts into the metal box making sure that the wires are clear of the hemisphere and dowered when positioned in hemisphere and dowered when positioned in mounting bracket.

B. Push all connected wires up into ceiling box.

• Position the receiver into the mounting bracket as shown direction.
• When installing the canopy, ensure the antenna is not pressed by the canopy.
• Make sure to connect all ground wires.
  

C.FUNCTION INSTRUCTION OF EMITTER

• Learning code and matching mode is used between emitter and receiver.

• Open battery cover on the hand-held remote and install battery, pair of AAA of emitter
  (1.5V) that are not included.

• If the emitter can not control the fan, learning code matching mode is used between
  emitter and receiver.
  Turn “ON” the supply power within 10 seconds and press the emitter’s “ ¢ ” button for 5
  seconds, it can load normally after hearing a long sound “bee”, which means learning
  successfully and it can works normally.

• When the emitter cannot control the receiver, please check the battery switch touching
  normally or not, correction of the positive and negative, full or empty of the power.

• When the emitter cannot control the receiver, please check is there any existence of
  similar remote controlled products nearby, then check whether they works, because
  remote controlled product with the same frequency will disturb each other.

• Please take out the battery from the emitter when leaving unused for long time.

• hen installing the fan, the fan ceiling cover don’t press the antenna(or other wire),it is
  easy to breakdown the wire and short-circuited.

  1. Fan On/Off
  2. 2 Natural Wind.
  3. Speed Controller
  4. Reverse Function
  5. Timer
  6. Light ON
  7. Light OFF

Step6 MOUNTING FAN ASSEMBLY

• Place two screws and washers on mounting bracket which correspond with slots in
  canopy. Screw in two turns.

Step7 ENGAGE HEMISPHERE

• Carefully rotate fan assembly until groove in hemisphere locks over tab of canopy assembly.

• Loosen (do not remove) the two screws on mounting bracket. Slide the canopy up to
  mounting bracket and place the key hole on the canopy over the screw on the mounting
  bracket, turn canopy until it locks in place at the narrow section of the key holes.

• Align the holes on the canopy with mounting bracket and secure with the two set of
  screws until snug.

WARNING : Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard.

NOTE : When installing fan on sloped ceiling, make sure tab on hanger bracket faces towards the
top of the slope. Depending on the slope, a longer dowered may be required to prevent fan blades
from hitting the ceiling.

Troubleshooting Guide

If you have difficulty operating your new ceiling fan it may be the result of incorrect assembly, installation, or wiring. In some cases these installation errors may be mistaken for defects. If you experience faults please check this troubleshooting guide.

•  Check the main and branch circuit fuses or breakers.
• CI Check the line wire connections to the fan and switch wire connections in the switch housing’s
• Check the battery in the remote contralto 
• Ensure you are in the normal range of 10-20 feet.

2| If fan sounds noisy.|

• Ensure all motor housing screws are snug
• Ensure the screws that attach the fan blade bracket to the motor hub are tightrope
• Ensure the wire nut connections are not rattling against each other or the interior wall of the switch housing’s
• Observe whether the noise decreases after the fan has been running for 24 hours. Newly installed fans may have noise issues’
• If you are using the Ceiling Fan light kit, ensure the screws securing the glassware are tight. Check that the light bulbs are also secure
• Ensure the canopy is a short distance from the ceiling. It should not touch the ceiling’s 
• Ensure your outlet box is a secure and rubber isolation pads were used between the mounting plate and outlet box.

3| If fan wobbles.|

• Check that all blades are screwed firmly into blade hollers.
• heck that all blade holders are tightened securely to motor.
• Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and junction box is mounted firmly to ceiling joist’s Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades keeping measure within 1/8 in. Rotate the fan until the next blade is positioned for measurement. Repeat for each blade. If all blade levels are not equal you can adjust blade levels by the following procedure. To adjust a blade tip down insert a washer (not supplied) between the blade and blade holder at the screw closest to the motor. To adjust a blade tip up insert washer (not supplied) between the blade and blade holder at the two screws farthest from the motor.
• If blade wobble is still noticeable interchanging two adjacent ( side by side ) blades can redistribute the weight and possibly result in smoother operation.

4| If light does not work.|

• Check blue wire from fan to make sure it is connected to hot wire from the house.
• Check for loose or disconnected wires in fan switch housing’s
• Check for loose or disconnected wires in light kite **** Check for faulty light bulbs. CAUTION: Make sure main power is turned off before entering switch housing’s 
• If the fan light shuts off shortly after being switched on it may be due to excessive current demand. Turn off power to the fan and replace the light bulbs with lower wattage bulbs. Turn on power to the fan using the pull chain, wall switch, or remote control ( whichever is installed on the particular fan ).

Balancing Kit

The Balancing kit should only be used if there is an unacceptable amount of fan wobble after
completing all the steps in your Owners Manual under “Attaching The Fan Blades.”

1. 1. Turn the fan on and set the speed control setting to a speed at which the wobbles is
   the greatest.

2. Turn off the fan and allow it to a come to a complete stop. Select one blade and place
   the balance clip on it, halfway between the blade holder and the blade tip on the trailing
   edge of blade.

3. Turn the fan on. Note whether the wobble has increased or decreased. Turn the fan off,
   move the clip to another blade, and retest. Repeat this procedure on all blades noting
   the blade on which the greatest improvement is achieved.

4. Move the clip back to the blade that showed the greatest improvement. Move the clip
   inward and outward on this blade and operate the fan to find the position where the clip
   gives the greatest improvement.

5. Remove the clip and install a balancing weight to the top of blade along the center line
   near the point where the clip was positioned.

6. If the fan wobble problem has not been corrected you can try to improve the balancing
   further by using the balancing clip and additional weights.
   

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>