SuperSprings MXKT Mounting Kit Instruction Manual

SuperSprings MXKT Mounting Kit

Product Information

Product Usage Instructions

1. Ensure the vehicle is on a level surface, the parking brake is ON, and the ignition is OFF.
2. Place blocks in front of and behind the front tires to prevent the vehicle from moving.
3. Disassemble the product if it has been preassembled.
4. Place the W-Bracket (Item A) on top of the factory leaf springs directly above the axle, straddling the factory spring plate.
5. Install the SuperSprings on top of the W-Bracket following the instructions included with SuperSprings.
6. Secure the SuperSprings to the W-Bracket using the Hold Down Plates (Item F), 5/16 Bolts (Item H), 5/16 Flat Washers (Item I), and 5/16 Nylock Nuts (Item G).
7. After driving for 200-500 miles, securely retighten all hardware.

TOOLS REQUIRED

• Floor Jack
• Safety Jack Stands
• Wheel Chocks
• ¾” Wrench/Socket
• ½” Wrench/Socket

PRIMARY APPLICATIONS

• Used for installation of SuperSprings Kits for various applications

PARTS LIST

PARTS LIST – STANDARD INSTALLATION

IMPORTANT NOTICE: Your part may have been loosely preassembled to show the new product as it will be once installed on your vehicle. Please disassemble the product before proceeding to the installation.

INSTALLATION

1. Positioning the vehicle – The vehicle must be on a level solid surface. Ensure the emergency brake is ON and the Ignition is OFF. Check both the front and rear of the front tires to prevent the vehicle from moving.
2. Jack up vehicle – elevate and support the frame securing with jack stands so that the axle is hanging with the tires slightly on the ground. Wheel removal is suggested ONLY where bodies are mounted.
3. Place W-Bracket [ITEM A] on top of the factory leaf springs directly above the axle, straddling the factory spring plate.
4. Using the Square U-bolts [ITEM B], Cross Plates [ITEM C], ½” Flat Washers [ITEM D], and ½” Nylock Nuts [ITEM E], fasten the W-Bracket to the leaf springs as in the diagram.
5. Install the SuperSprings on top of the W-Bracket (see instructions included with SuperSprings).
6. Secure the SuperSprings to the W-Bracket using the Hold Down Plates [ITEM F], 5/16″ Bolts [ITEM H], 5/16″ Flat Washers [ITEM I], and 5/16″ Nylock Nuts [ITEM G].
7. Securely retighten all hardware after 200-500 miles of driving.

Part Number: MXKT

• SuperSprings
• International, Inc.
• 505 Maple Avenue
• Carpinteria, CA 93013
• Installation Support
• +1 800-898-0705
• support@supersprings.com.
• superspringsint.com.

Product Line: MOUNTING KITS

• SAFETY NOTICE: We recommend installation be done by a professional or persons with sound mechanical knowledge.
• WARNING: These instructions are a general guide for installation. SuperSprings International, Inc. assumes no liability for the actual installation process. Consumers and installers should apply common automotive safety practices when raising and working on any vehicle. Do not put yourself in a position where, if the vehicle were to move unexpectedly, you may be injured. SuperSprings’ products are designed to improve vehicle ride quality. Do not load any vehicle beyond the manufacturer’s specifications. Never exceed the manufacturer’s Gross Vehicle Rating (GVWR) located on your vehicle’s identification tag.
• BEFORE INSTALLATION: Ensure the vehicle is on a level surface, the parking brake is ON, with the ignition OFF, and place blocks in front of and behind the front tires to prevent the vehicle from moving.
• DURING AND/OR AFTER INSTALLATION: Ensure emergency brake cables are not touching the SuperSprings. Secure any cables out of the way with zip ties or by re-routing. Ensure all A/C lines, brake cables, and frame are clear of contact or interference.
• REV. 2.0
• FEB 2022

References

• SuperSprings International | Journey Better

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>