SuperSprings MTKT Mounting Kit for OEM Leaf Springs Instruction Manual
- June 13, 2024
- SuperSprings
Table of Contents
SuperSprings MTKT Mounting Kit for OEM Leaf Springs Instruction Manual
TOOLS REQUIRED
- Floor Jack
- Safety Jack Stands
- Wheel Chocks
- ¾” Wrench/Socket
- ½” Wrench/Socket
PRIMARY APPLICATIONS
Used for installation of SuperSprings
Kits for various applications
PARTS LIST – STANDARD INSTALLATION
| Item | Part # | Discription | QTY |
|---|---|---|---|
| A | 112211 | MTKT W-Bracket | 2 |
| B | 112202 | ½-13 Square U-Bolt | 4 |
| C | 112203 | Mounting Kit Cross Plate | 4 |
| D | 112130 | ½” Flat Washer | 8 |
| E | 112126 | ½-13 Nylock Nut | 8 |
| F | 112282 | Hold Down Plate | 4 |
| G | 112208 | 5/16-18 Nylock Nut | 4 |
| H | 112215 | 5/16-18 x 2-½” Hex Bolt | 4 |
| I | 512244 | 5/16 Flat Washer | 8 |
IMPORTANT NOTICE: Your part may have been loosely preassembled to show the nal product as it will be once installed on your vehicle.
Please disassemble the product before proceeding to the installation.
INSTALLATION
- Positioning the vehicle – Vehicle must be on level solid surface. Ensure emergency brake is ON and Ignition is OFF. Chock both front and rear of the front tires to prevent the vehicle from moving.
- Jack up vehicle – elevate and support the frame securing with jack stands so that the axle is hanging with tires slightly off the ground. Wheel removal is suggested ONLY were bodies are mounted.
- Place W-Bracket [ITEM A] on top of factory leaf springs directly above the axle, straddling the factory spring plate.
- Using the Square U-bolts [ITEM B], Cross Plates [ITEM C], ½” Flat Washers [ITEM D], and ½” NY lock Nuts [ITEM E], fasten the W-Bracket to the leaf springs as in the diagram.
- Install the Super Springs on top of the W-Bracket (see instructions included with Super Springs).
- Secure the Super Springs to the W-Bracket using the Hold Down Plates [ITEM F], 5/16″ Bolts [ITEM H], 5/16″ Flat Washers [ITEM I], and 5/16″ NY lock Nuts [ITEM G].
- Securely retighten all hardware after 200-500 miles of driving
Part Number: MTKT
SuperSprings
International, Inc.
505 Maple Avenue
Carpnteria, CA 93013
Installation Support
+1 800-898-0705
support@supersprings.com
superspringsint.com
Product Line: MOUNTING KITS
SAFETY NOTICE: We recommend installation be done by a professional or persons with sound mechanical knowledge.
WARNING: These instructions are a general guide for installation. Super
Springs International, Inc. assumes no liability for the actual installation
process.
Consumers and installers should apply common automotive safety practices when
raising and working on any vehicle. Do not put yourself in a position
where, if the vehicle were to move unexpectedly, you may be injured.
Super Springs’ products are designed to improve vehicle ride quality. Do not
load any vehicle beyond the manufacturer’s specifications.
Never exceed the manufacturer’s Gross Vehicle Rating (GVWR) located on your vehicles identification tag.
ensure the vehicle is on a level surface, the parking brake is ON, with the ignition OFF, and place blocks in front of and behind the front tires to prevent the vehicle from moving.
DURING AND/OR AFTER INSTALLATION: Ensure emergency brake cables are not touch-ing the SuperSprings. Secure any cables out of the way with zip ties or by re-routing. Ensure all A/C lines, brake cables, and frame are clear of contact or interference.
REV. 2.0 | FEB 2022
Documents / Resources
|
SuperSprings MTKT Mounting Kit for OEM Leaf
Springs
[pdf] Instruction Manual
MTKT Mounting Kit for OEM Leaf Springs, MTKT, Mounting Kit for OEM Leaf
Springs, OEM Leaf Springs, Leaf Springs, Springs
---|---