SuperSprings SSA25 Rear Helper Spring Kit Instruction Manual
- June 13, 2024
- SuperSprings
Table of Contents
SuperSprings SSA25 Rear Helper Spring Kit
Product Information
- Part Number: SSA25
- Product Line: SUPERSPRINGS
- Manufacturer: SuperSprings International, Inc.
- Address: 505 Maple Avenue Carpnteria, CA 93013
- Contact: Installation Support +1 800 898 0705, support@supersprings.com
- Website: superspringsint.com
Product Usage Instructions
Safety Notice
We recommend installation be done by a professional or persons with sound
mechanical knowledge. Never exceed the manufacturer’s Gross Vehicle Rating
(GVWR) located on your vehicle’s identification tag.
Before Installation
- Ensure the vehicle is on a level surface.
- Engage the parking brake and turn off the ignition.
- Place blocks in front of and behind the front tires to prevent the vehicle from moving.
During and/or After Installation
Ensure emergency brake cables are not touching the SuperSprings. Secure any
cables out of the way with zip ties or by re-routing. Ensure all A/C lines,
brake cables, and frame are clear of contact or interference.
Installation Instructions
Important Notice
Your part may have been loosely preassembled to show the final product as
it will be once installed on your vehicle. Please disassemble the product
before proceeding to the installation.
Installation Steps:
- The SSA25 has a dedicated front and rear. The 4 Hole Shackle Leg [ITEM I] should be toward the front of the truck, and the threaded ends of the spring eye bolts should be pointing outboard, away from the frame.
- Place PSP-7 [ITEM B], on top of the factory spring-plate, centered between the u-bolts. The PSP-7 is double sided, so whichever side fits the spring plate better is the side that should face down.
- Per the diagram, place the Lock Down U-Bolt [ITEM C] around the SuperSpring so the threads are facing up. Install the Lock Down Clamp [ITEM D] onto the u-bolt with the open side down and center on spring blade as shown.
- Using 9/16 wrenches/sockets/ratchet, install the 3/8 Flange Nuts [ITEM E] onto the Lock Down U-Bolt [ITEM C]. Only partially tighten the nuts so that the clamp assembly can still be moved freely on the spring blade.
Please refer to the complete user manual for detailed installation instructions and diagrams.
BEFORE YOU BEGIN
TOOLS REQUIRED
- Floor Jack
- Safety Jack Stands
- Wheel Chocks
- 1-1/16″ Wrench/Socket
- 1-1/8″ Wrench/Socket
- 9/16″ Wrench/Socket
- Heavy Duty Clamps or SuperSprings Installation Tool
PRIMARY APPLICATIONS
- Chevrolet C4500 Kodiak 4 X 2 (2003 – 2009)
- Chevrolet C5500 Kodiak 4 X 2 (2003 – 2009)
- Dodge RAM 2500 4 X 2 & 4 X 4 (1994 – 2002)
- Dodge RAM 3500 4 X 2 & 4 X 4 (1994 – 2002)
- Ford F-250 Super Duty 4 X 2 & 4 X 4 (2011 – present)
- Ford F-350 Super Duty 4 X 2 & 4 X 4 (1999 – 2016)
- Ford F-450 Super Duty 4 X 2 & 4 X 4 (1999 – present)
- Ford F-550 Super Duty 4 X 2 & 4 X 4 (1999 – present)
- GMC C4500 Topkick 4 X 2 (2003 – 2009)
- GMC C5500 Topkick 4 X 2 (2003 – 2009)
PARTS LIST – STANDARD INSTALLATION
INSTALLATION
- Positioning the vehicle – Vehicle must be on level solid surface. Ensure emergency brake is ON and Ignition is OFF. Chock both front and rear of the front tires to prevent the vehicle from moving.
- Jack up vehicle – elevate and support the frame securing with jack stands so that the axle is hanging with tires slightly o˙ the ground. Wheel removal is suggested ONLY were bodies are mounted.
- The SSA25 has a dedicated front and rear. The 4 Hole Shackle Leg [ITEM I] should be toward the front of the truck, and the threaded ends of the spring eye bolts should be pointing outboard, away from the frame.
- Remove Shackle Roller Assemblies – Using 1 1/16″ and 1 1/8″ tools, wrenches / sockets / ratchet, remove and set aside the bolts [items N] and nuts [item L] retaining the Rollers [ITEM H] and Sleeves [ITEM G] from the front and rear of the shackles. Rotate the Shackles [ITEM I & J] toward the center and parallel to the spring.
- PSP Install – Place PSP-7 [ITEM B], on top of the factory spring-plate, centered between the u-bolts. The PSP-7 is double sided, so whichever side ÿts the spring plate better is the side that should face down.
- Per the diagram, place the Lock Down U-Bolt [ITEM C] around the SuperSpring so the threads are facing up. Install the Lock Down Clamp [ITEM D] onto the u-bolt with the open side down and center on spring blade as shown. Using 9/16″ wrenches / sockets / ratchet, install the 3/8 Flange Nuts [ITEM E] onto the Lock Down U-Bolt [ITEM C]. Only partially tighten the nuts so that the clamp assembly can still be moved freely on the spring blade.
- Place the SuperSpring on top of the PSP-7 [ITEM B] above the OE leaf pack. Position the lockdown assembly so that the base of the u-bolt is placed between the front and center bumps of the PSP-7 mounting pad. Ensure that the 4 Hole Shackle [ITEM I] is to the front and the threads of the bolts are facing outboard, away from the frame.
- Shackle Attachment – Note: The top/spring eye shackle bolts are factory pre-torqued; no adjustment/ˆrther tightening is needed. If any are loosened by the installer then retorque to 30 ˇ. lbs.
- Shackle Attachment Front – Rotate the front shackles legs down on both sides of the leaf spring. Using a SuperSprings Installation Tool or other high capacity clamp(s), compress the SuperSprings and factory leaf pack together. Place the Sleeve [ITEM G] and the Roller [ITEM H] between the Shackles and align with desired preload holes. Secure with ¾-10 x 5″ Hex Bolt [ITEM N] and ¾-10 Lock Nut [ITEM L]. Torque to 35 ˇ. lbs. Ensure there is clearance on all sides of the shackle.
- Shackle Attachment Rear – Rotate the rear shackles legs down on both sides of the leaf spring. Using a SuperSprings Installation Tool or other high capacity clamp(s), compress the SuperSprings and factory leaf pack together. Place the Sleeve [item G] and the Roller [item H] between the Shackles and align with desired preload holes. Secure with ¾-10 x 5″ Hex bolt [ITEM N] and ¾-10 Lock Nut [ITEM L]. Torque to 35 ˇ. lbs.
- Adjust spring location front to back so that the Rollers have minimum ½” of clearance from spring clamps or the end of the next shorter leaf. Also conÿrm that there is adequate clearance around the SuperSpring from the frame, brake lines, harnesses, etc. In some cases, it may be necessary to bend routing brackets to adjust position of the brake lines or harnesses for clearance.
- Secure Lock-down Hardware – Tighten 3/8 Locking Flange Nuts [ITEM E] evenly and securely. Do not over tighten or distort plate shape to excess.
- Repeat steps 3 through 10 on the other side.
- Lower the vehicle – elevate chassis, remove the jack stands, lower to the ground. Remove wheel chocks from front wheels.
- Final Check – Check the position of the SuperSprings ensuring for correct hardware application and orientation. Observe all hardware ensuring for static and dynamic interference clearances. Recheck all hardware to ensure it is securely tightened.
NOTE: Aˇer 200-500 miles of driving, recheck all hardware again for tightness.
SAFETY INSTRUCTION
-
SAFETY NOTICE
-
We recommend installation be done by a professional or persons with sound mechanical knowledge.
WARNING: These instructions are a general guide for installation. SuperSprings International, Inc. assumes no liability for the actual installation process. Consumers and installers should apply common automotive safety practices when raising and working on any vehicle. Do not put yourself in a position where, if the vehicle were to move unexpectedly, you may be injured. SuperSprings’ products are designed to improve vehicle ride quality. Do not load any vehicle beyond the manufacturer’s speciÿcations. -
Never exceed the manufacturer’s Gross Vehicle Rating (GVWR) located on your vehicles identification tag.
-
-
BEFORE INSTALLATION:
E nsure the vehicle is on a level surface, the parking brake is ON, with the ignition OFF, and place blocks in front of and behind the front tires to prevent the vehicle from movin g. -
DURING AND/OR AFTER INSTALLATION:
Ensure emergency brake cables are not touch-ing the SuperSprings. Secure any cables out of the way with zip ties or by re-routing. Ensure all A/C lines, brake cables, and frame are clear of contact or interference.
ABOUT COMPANY
- SuperSprings
- International, Inc.
- 505 Maple Avenue
- Carpnteria, CA 93013
- Installation Support
- +1 800-898-0705
- support@supersprings.com
- superspringsint.com