SuperSprings SSR-129-40-2 SumoSprings Rebel Kit Rear Instruction Manual

June 13, 2024
SuperSprings

INSTALLATION INSTRUCTIONS
PART NUMBER
SSR-129-40-2/47-2

BEFORE YOU BEGIN

PRIMARY APPLICATIONS

Ford F-250 Super Duty 4 X 2 (2017 – present)
Ford F-350 Super Duty 4 X 2 (2017 – present)
TOOLS REQUIRED
Floor Jack
Jack Stands
Wheel Chocks
Standard Sockets & Wrenches
Metric Sockets & Wrenches
PARTS LIST

Item Part # Discription QTY
A 511419 SumoSprings Blue -40 2
511418 SumoSprings Black -47
B 512344 Upper Bracket 2 2
C 512345 Upper Bracket 1 2
D 512346 Lower Bracket 2
E 512244 5/16 Flat Washer 8
F 512323 3/8-16 Nylock Nut 8
G 512021 U-Channel Clamp 2
H 512356 3/8-16 Clip Nut 4
I 512340 3/8-16 x 1″ FHCS 4
J 512207 3/8-16 x ¾” Serrated Flange Bolt 6
K 512302 3/8 Flanged Lock Nut 8
L 512230 3/8 x 4″ x 6″ U-Bolt 2
M 112196 3/8 x 7 1/8″ x 5″ U-Bolt 2

SuperSprings SSR 129 40 2 SumoSprings Rebel Kit Rear -
BEGIN DRIVER SIDE (PASSENGER SIDE SIMILAR)
Part Number: SSR-129-40-2/47-2

SAFETY NOTICE: We recommend installation be done by a professional or persons with sound mechanical knowledge.
WARNING: These instructions are a general guide for installation. SuperSprings International, Inc. assumes no liability for the actual installation processConsumers and installers should apply common automotive safety practices when raising and working on any vehicle. Do not put yourself in a position where, if the vehicle were to move unexpectedly, you may be injuredSuperSprings’ products are designed to improve vehicle ride quality. Do not load any vehicle beyond the manufacturer’s specifications.
Product Line: SUMOSPRINGS REAR
Never exceed the manufacturer’s Gross Vehicle Rating (GVWR) located on your vehicles identification tag.
BEFORE INSTALLATION: Ensure the vehicle is on a level surface, the parking brake is ON, with the ignition OFF, and place blocks in front of and behind the front tires to prevent the vehicle from moving.
DURING AND/OR AFTER INSTALLATION: Ensure emergency brake cables are not touch-ing the SuperSprings. Secure any cables out of the way with zip ties or by re-routing. Ensure all A/C lines, brake cables, and frame are clear of contact or interference.
IMPORTANT NOTICE: Your part may have been loosely preassembled to show the final product as it will be once installed on your vehicle.
Please disassemble the product before proceeding to the installation.

INSTALLATION

  1. Park vehicle of level hard surface. Place wheel chocks in front and behind the front wheels to prevent rolling. Observe all safety precautions and wear safety glasses.
  2. Raise the rear of the vehicle allowing the axle to hang free and rest the frame on the safety jack stands rated for the weight of the vehicle. Removal of the rear wheels is optional.
  3. Starting on the driver side un-bolt and remove the factory jounce bumpers from the underside of the frame and remover the factory studs that are clipped into the frame.
  4. Attach two 3/8 Clip Nuts [ITEM H] onto the frame where the factory studs were positioned. Ensure that the threaded portion is up inside the frame.
  5. Using the two 3/8-16 FHCS [ITEM I], attach the Upper Bracket 1 [ITEM B] to the frame with the bent end toward the front of the vehicle as in the diagram. Place a drop of the blue locktite on the threads of each bolt.
  6. Using two 3/8 Serrrated Flange Bolts [ITEM J] attach the top half of the SumoSpring [ITEM A] to the Upper Bracket 2 [ITEM C]. Leave the bolts slightly loose so that the position of the SumoSpring can be adjusted.
  7. Place the Upper Bracket 2 and SumoSpring assembly [ITEM C & A] onto the studs of the Upper Bracket 1 [ITEM B]. The end of item B with the bend goes toward the rear of the truck as in the diagram. Fasten the brackets together with four 3/8 Flanged Lock Nuts [ITEM K].
  8. Place one U-Bolt [ITEM L] into the inner groove of the Lower Bracket [ITEM D] as seen in diagram.
  9. Using one 3/8 Serrated Flange Bolt [ITEM J] attach the lower half of the SumoSpring to the Lower Bracket [ITEM D]. Leave the bolt slightly loose so that the position can be adjusted.
  10. Place the lower assembly on the axle and position tight to the leaf pack.
  11. Align upper and lower halves of the SumoSpring using a jack to raise the axle if necessary.
  12. Once the top and bottom of the SumoSpring are lined up, tighten the bolts [ITEM J].
  13. Place the U-Bolt [ITEM M] around the factory u-bolts and below the leaf pack so that the ends protrude through the holes in the Lower Bracket [ITEM D] and fasten securely with 5/16 Flat Washers [ITEM E] and 3/8-16 Nyloc Nuts [ITEM F].
  14. Place the U-Channel Clamp [ITEM G] over the ends of the U-Bolt [ITEM L] and fasten tight to the bottom of the axle using the 5/16 Flat Washers [ITEM E] and 3/8-16 Nyloc Nuts [ITEM F].
  15. Repeat steps 3 through 14 on passenger side of truck.
  16. If rear wheels were removed you can now reinstall the rear wheels and torque wheel nuts to manufacturers specifications. Jack up vehicle, remove safety jack stands. Remove wheel chocks from the front wheels.
  17. Register the warranty for your SuperSprings International part. A warranty card can be found in the box your part came in.

SuperSprings
International, Inc.
505 Maple Avenue
Carpnteria, CA 93013
Installation Support
+1 800-898-0705
support@supersprings.com
superspringsint.com 

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SuperSprings User Manuals

Related Manuals