V-LOC XV-TD Touch Dimmer User Guide
- June 6, 2024
- V-LOC
Table of Contents
V-LOC XV-TD Touch Dimmer
Certifications
- ROHS compliant
- EMC: Meets FCC47 CFR Part 15
(Class B) consumer limits @ 120V
Package Includes
| Hatch TOUCH Dimmer Pad | 1 |
|---|---|
| Integrated 6’ 3-conductor cable | 1 |
| Quick Start Guide | 1 |
Dimensions IN/[MM]
| Length: | 1.6 [40.64] |
|---|---|
| Width: | 1.15 [29.21] |
| Height: | 0.25 [6.35] |
Description
The XV-TD TOUCH Dimmer is designed to be used with Hatch Lighting V-LOC
constant voltage LED drivers. It connects to the driver with a simple 3.5mm
jack at the end of the integral 6’ cable. The dimmer requires no batteries or
external power source. Once connected the TOUCH Dimmer can be used to control
the brightness of the LED load and also turn on or turn off the LED load. It’s
soft blue back-lit keypad allows it to be easily seen in an otherwise dark
room and its light weight design and compact size provides maximum mounting
flexibility.
The TOUCH Dimmer can also be used to set the maximum brightness level for
applications in which dimming is not required and the customer desires less
light output when the V-LOC driver is switched on. Please see the Maximum
Brightness Setting section under Operating Instructions for more details.
BEFORE BEGINNING INSTALLATION, READ THESE IMPORTANT SAFETY INSTRUCTIONS
When using electrical equipment, basic safety precautions should always be
followed.
Warnings
DO NOT CONNECT ANY EQUIPMENT TO THE V-LOC LED DRIVER TOUCH DIMMER PORT
OTHER THAN THE HATCH XV-TD TOUCH DIMMER. CONNECTING ANYTHING OTHER THAN THE
HATCH XV-TD TOUCH DIMMER MAY DAMAGE THE V-LOC LED DRIVER.
THERE ARE NO SERVICEABLE PARTS, BATTERIES OR MOUNTING FEATURES INSIDE THE TOUCH DIMMER. DO NOT ATTEMPT TO DISASSEMBLE THE DIMMER. DOING SO WILL VOID THE WARRANTY.
BEFORE DRILLING ANY HOLES OR USING NAILS OR SCREWS TO MOUNT THE TOUCH DIMMER,
VERIFY THAT THERE IS NO CONCEALED WIRING BEHIND THE MOUNTING SURFACE THAT MAY
BE PUNCTURED OR DAMAGED.
INSTALL ATION INSTRUCTIONS
Prior to beginning installation, read user guide completely.
-
Make sure power to the driver is switched off. If driver is connected to an unswitched power source, turn power off at the breaker panel.
-
Locate the Hatch V-LOC LED driver and the TOUCH Dimmer jack on the side of the driver.
-
Determine the desired location for the TOUCH Dimmer.
Consider factors like visibility, TOUCH Dimmer cable routing and ease of access when selecting TOUCH Dimmer location.
-
Determine desired routing path for TOUCH Dimmer cable location. For routing convenience and aesthetic purposes the TOUCH Dimmer cable exit is designed such that the cable can exit either the base of the dimmer or the end of the dimmer.
-
Drill 3/8” hole in locations as needed for routing TOUCH Dimmer cable plug.
-
Route and anchor cable as needed. Be careful not to pierce or damage cable insulation when routing and anchoring.
-
After routing and anchoring cable, insert TOUCH Dimmer plug into Hatch V-LOC LED driver TOUCH dimmer port.
-
Remove adhesive backing from TOUCH Dimmer base and affix in desired location.
-
Restore power to the Hatch V-LOC LED driver.
OPERATING INSTRUCTIONS
On/Off Mode
To turn the V-LOC driver on or off, simply touch or tap the center of the
TOUCH Dimmer and
release. If a dim level has previously been set, tapping the TOUCH Dimmer will
turn the lights off.
Tapping it again will turn the lights back on to the previous dim level.
Up/Down Dimming Mode
For changing the dim level, contact with the TOUCH Dimmer is maintained. While
maintaining
contact with the TOUCH Dimmer, the lights will dim down to the minimum dimming
level, then begin to increase in intensity. Once the desired intensity level
is obtained, simply discontinue contact with the TOUCH Dimmer and that level
of brightness will be the new set point when turning on and off the LED lights
attached the V-LOC LED driver.
Maximum Brightness Setting
The V-LOC Touch Dimmer can be used to program the maximum brightness of a
V-LOC driven LED system in non-dimming applications, such as scene or ambiance
control. Once the system, including all LED loads, is installed, plug the
TOUCH Dimmer into the V-LOC LED driver. Power on the system then use the TOUCH
Dimmer to set the lighting level to the desired maximum brightness using the
steps described in Up/ Down Dimming Mode. To complete programming turn the
V-LOC system off and back on with single touches. Disconnect the TOUCH Dimmer.
The last brightness setting will now be programmed as the maximum.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Hatch Lighting:
XV-TD
7821 Woodland Center Boulevard, Tampa, FL 33614