HEARTH HOME technologies PRIMO-II Series Driftwood Logs Instruction Manual

June 13, 2024
HEARTH HOME technologies

HEARTH HOME technologies logo

Traditional Logs, Driftwood Logs, Birch Logs
OAKLG-LIN-SM/LG, DWLG-LIN-SM/LG, BIRLG-LIN-SM/LG
Model: PRIMO-II Series

PRIMO-II Series Driftwood Logs

Leave this manual with party responsible for use and operation.

CAUTION: Logs are fragile, handle with care.

NOTICE: To simplify the installation process, positively identify each individual log before beginning installation.
See Figures 1A – 1F. The individual logs for the Traditional (OAKLG), Driftwood (DWLG) and Birch (BIRLG) log sets will install in a similar manner. The Driftwood logs are featured in the figures. Key log location features are shown in Figure 2. Logs are NOT  installed in sequential order.

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - HEARTH HOME
technologies PRIMO-II Series Driftwood Logs

Preparation: Install log locating pins, included in hardware bag, into all locations as shown in the figures below. Extra log pins are included in manual bag. Log pins are identified alphabetically as shown below. Log pin holes are circular in shape, with the  exception of a few rectangular holes, which are shaded in Figures 2A, 2B and 2C. The rectangular holes are only used for placement on See-Through (ST) models and for Single-Sided models that use black glass (BGK) refractory kits.
See Figure 2.D.

HEARTH HOME technologies PRIMO-II Series Driftwood Logs -
Partrs

Log Installation: OAKLG-LIN-SM / DWLG-LIN-SM / BIRLG-LIN-SM
Models: PRIMO-II-48, PRIMO-II-48ST
Log #10: Place Log #10 in back left of firebox using log pins (A) and (B) for positive placement. Place the right side of Log #10 against log pin (B) and then pivot the left side of Log #10 back to meet log pin (A). See Figure 1.
Log #3: Place the left side of Log #3 against log pin (C) and pivot the right side of Log #3 back to meet log pin D. See Figure 2.

HEARTH HOME technologies PRIMO-II Series Driftwood Logs -
2

Log #5 : Place the left side of Log #5 against log pin (E). For See Through models and those using black glass refractory, pivot the right side back until it contacts log pin (F). See Figure 3. For installations with fiber refractory, the back right side will contact the  refractory.
Log #2: Place the right side of Log #2 on the flat spot on the left side of Log #3. Pivot the left side forward until it contacts the media tray ledge. See Figure 4.

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Partrs
3

Log #8 : Log #8 uses three log pins, J, K and L. Place Log #8 as shown in Figure 5.
Log #7: Set the right side of Log #7 on the left side of Log #8. There should be a one inch overlap as noted in Figure 6.
Pivot the left side of Log #7 back until it contacts log pin (I.)

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Partrs
4

Log #6 : Insert the left side support feature of Log #6 into the recess on Log #5. Pivot the right side of the log forward as far as it can go. Ensure the log is stable and fully engaged with Log #5, the supporting log. See Figure 7.
Log #1: Place the end of Log #1 against log pins (G) and (H) in the back right corner of the firebox. The log should curve outward as shown. Set the front end of Log #1 on top of Log #6 as shown in Figure 8.

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Partrs
5

Media Placement : Install required media as instructed in the appliance Installation Manual.

Log Installation: OAKLG-LIN-LG / DWLG-LIN-LG / BIRLG-LIN-LG
Models: PRIMO-II-60, PRIMO-II-60ST
Log #1: Center the log left to right between the log pins noted in Figure

  1. Slide Log #1 back until it contacts both log pins.
    See Figure 2.

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Partrs
6

Log #3: Place the left side of Log #3 against log pin (C). Pivot the right side of the log backward until it contacts the log pin (D) at the rear (black glass refractory and see-through installations) or the fiber refractory. See Figure 3.
Log #5: Place the left side of Log #5 against the left log pin (E). Pivot the log backwards until it contacts the rear log pin (F) for See Through models and those using black glass refractory. For installations with fiber refractory, the log will contact the refractory. See Figure 4.

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Partrs
7

Log #8: Place the right side of Log #8 against the right log pin (H). Pivot the left side forward until it contacts the front log pin (G). See Figure 5.
Log #2: Set the right side of Log #2 on Log #3 as shown in Figure 6. Pivot the left base of the log forward until it contacts the media tray ledge.

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Partrs
8

Log #4: Place Log #4 against the right log pin (K). Pivot the log backward until it contacts the left log pin (J). See Figure 7.
Log #7: Set the right side of Log #7 on Log #4 as shown in Figure 8. There should be a 1-1/2 inch overlap as noted. Pivot the left side of the log forward until it contacts the media tray ledge.

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Partrs
9

Log #6: Insert the left side support feature of Log #6 into the recess on Log #5 as shown in Figure 9. Pivot the right side of the log forward until it contacts the media tray ledge. Ensure the log is stable and fully engaged with the supporting log.
Log #9: Set the left side of Log #9 on the support area of Log #6. Pivot the right side base of the log backward until it contacts the rear log pin (I) for See Through models and those using black glass refractory. See Figure 10. For installations with fiber refractory,  the right side will contact the back refractory.

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Partrs
10

Log #10: Place the left side of Log #10 against the left log pin (L). Pivot the right side of the log backward until it contacts the rear log pin (M). See Figure 11.

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Partrs
11

Media Placement : Install required media as instructed in the appliance Installation Manual.

Log Installation: OAKLG-LIN-LG / DWLG-LIN-LG / BIRLG-LIN-LG
Models: PRIMO-II-72, PRIMO-II-72ST

Log #1: Center Log #1 left to right between log pins (A) and (B) as shown in Figure 1 and Figure 2. Slide Log #1 back until it contacts both log pins.

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Partrs
12

Log #3: Place the left side of Log #3 against log pin (C). Pivot the right side of the log backward until it contacts the rear pin (D) for See Through models and those using black glass refractory. See Figure 3. For installations with fiber refractory, the log will  contact the back refractory.
Log #5: Place the left side of Log #5 against log pin E. Pivot the right side of the log backward until it contacts the rear log pin (F). See Figure 4.

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Partrs
13

Log #7: Place the right side of Log #7 against the right log pin (H). Pivot the left side toward the burner until it contacts log pin (G). See Figure 5.
Log #2: Place the right side of Log #2 onto the support feature on Log

3. Pivot the left base of Log #2 forward until it contacts the media tray

ledge. See Figure 6.

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Partrs
14

Log #4: Place Log #4 against log pin K on the right shown in Figure 7 and Figure 8. Pivot the log backward until it contacts the left log pin (J). See Figure 7.
Log #6: Insert the left side support feature of Log #6 into the recess on Log #5. Pivot the right side of the log forward until it contacts the media tray ledge. Ensure the log is stable and fully engaged with the supporting log. See Figure 8.

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Partrs
15

Log #8: Set the right side of Log #8 next to log pin (M). Pivot the left side forward, away from the burner, to log pin (L) as shown in Figure 9.
Log #9: Set the left side of Log #9 on the support area of Log #8. Pivot the right side base of the log backward until it contacts the rear log pin (I) for See Through models and those using black glass refractory. For installations with fiber refractory, the right side  of Log #9 will contact the back refractory. See Figure 10.

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Partrs
16

Log #10: Place the left side of Log #10 against the left log pin (N). Pivot the right side of the log backward until it contacts the rear log pin (O). See Figure 11.

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Partrs
17

Media Placement: Install required media as instructed in the appliance Installation Manual.

Troubleshooting

If flames impinge upon the logs after installation, minor shifting of log position or media may be necessary to reduce flame impingement and sooting.

Log Sets Installed

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Log Sets
1Log Set Installed – PRIMO-II-48 OAK LOGS

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Log Sets
2

Log Set Installed – PRIMO-II-48 DRIFTWOOD

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Log Sets
3

Log Set Installed – PRIMO-II-48 BIRCH

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Log Sets
4

Log Set Installed – PRIMO-II-60 OAK LOGS

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Log Sets
5

Log Set Installed – PRIMO-II-60 DRIFTWOOD

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Log Sets
6

Log Set Installed -PRIMO-II-60 BIRCH

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Log Sets
7

Log Set Installed – PRIMO-II-72 OAK LOGS

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Log Sets
8

Log Set Installed – PRIMO-II-72 DRIFTWOOD

HEARTH HOME technologies PRIMO-II Series Driftwood Logs - Log Sets
9

Log Set Installed – PRIMO-II-72 BIRCH

Service Parts List

Service Parts List HHT Part # Model Description
501-836-25 PRIMO-II Series Log Pin (Quantity 25)
OAK HHT Part # Model Description
--- --- --- ---
OAKLG-LIN-SM PRIMO-II-48/ST Oak Linear Log Set – Small
OAKLG-LIN-LG PRIMO-II-60/ST, PRIMO-II-72/ST Oak Linear Log Set – Large
DRIFTWOOD HHT Part # Model Description
--- --- --- ---
DWLG-LIN-SM PRIMO-II-48/ST Driftwood Linear Log Set – Small
DWLG-LIN-LG PRIMO-II-60/ST, PRIMO-II-72/ST Driftwood Linear Log Set – Large
BIRCH HHT Part # Model Description
--- --- --- ---
BIRLG-LIN-SM PRIMO-II-48/ST   Birch Linear Log Set – Small
BIRLG-LIN-LG PRIMO-II-60/ST, PRIMO-II-72/ST Birch Linear Log Set – Large

HEARTH HOME technologies logo

Hearth & Home Technologies
OAKLG-LIN-SM/LG, DWLG-LIN-SM/LG, BIRLG-LIN-SM/LG Log Instructions
2682-949 Rev. B • 3/23

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

HEARTH HOME technologies User Manuals

Related Manuals