HEARTH HOME technologies ASD Series Mesh Door Kits Instruction Manual

June 12, 2024
HEARTH HOME technologies

HEARTH HOME technologies ASD Series Mesh Door Kits

HEARTH-HOME-technologies-ASD-Series-Mesh-Door-Kits-
product

Product Information
The product is a Mesh Door Kit designed for use on specific fireplace models. It is available in various models, including ASD-36, ASD-42, LSD-36, LSD-42, VOFBSD-36, and VOFBSD-42. Each model has a corresponding door model number for easy identification. The Mesh Door Kit is made of sheet metal and features a screen/mesh and glass doors. It is designed to be installed on fireplace models BUF36A and BUF42A. During installation, it is important to wear protective gloves and safety glasses due to the risk of cuts and abrasions from the sharp sheet metal edges. It is also important to note that the screen/mesh, glass doors, and other surfaces of the Mesh Door Kit can become hot during operation and take time to cool down. Caution should be exercised to avoid burns.

Prior to the initial burning of the fireplace, all fingerprints and smudges must be wiped clean from the viewable surfaces of the door kit. Failure to do so may result in these prints and smudges becoming permanent. To maintain the finish of the door kit, it is recommended to gently wipe it with a soft cloth and, if necessary, soap and water. Thinner or abrasive cleaners should never be used as they can damage the finish.

Product Usage Instructions

  1. Remove the existing screens from the fireplace.
  2. Hang the door frame assembly into the slots located on the firebox using the corresponding hooks on the door frame. Ensure that the door is fully down on the hooks and that there is approximately a 1/2-inch gap at the bottom of the frame.
  3. Install the inner hood by using the bend tabs to locate it. Slightly pry up the hand band tabs to position it correctly. Secure it in place using the screws from the screen rods.
  4. Leave the original hood in place.
  5. The mesh door installation is now complete.

Note : It is recommended to have two installers handle the heavy door kit during installation.

Mesh Door Kits

Door Model Number For Use on Models
ASD- 36 ACUF36- BD
BUF36- T BUF36- H
ASD- 42 ACUF42- BD
BUF42- T BUF42- H
VOFBSD-36 VOBF36-T
VOFBSD-42 VOBF42-T
LSD-36 LCUF36CR-C
GH**
LSD-42 LCUF42CR-C
GH**

These mesh door kits have been tested for use with specific Hearth & Home Technologies products. Check with your local building code agency before you begin installation to ensure compliance with local codes, including the need for permits and follow-up inspections. If you encounter any problems regarding code approvals, or if you need clarification of any of the instructions contained here, contact your Hearth & Home Technologies Inc. dealer. For the dealer nearest you, please visit www.hearthnhome.com.

CAUTION! Risk of Cuts/Abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

NOTICE: All fingerprints and smudges must be wiped clean from the viewable surfaces of the door kit prior to the initial burning of the fireplace. If this is not done, these prints and smudges will be cured into the finish and set for the life of the fireplace. To keep the finish looking its best, gently wipe with a soft cloth and if desired, soap and water. Never use thinner or abrasive cleaners since these products will damage the finish.

HEARTH-HOME-technologies-ASD-Series-Mesh-Door-Kits-fig-
\(2\)

WARNING

HOT SURFACES!
Screen/mesh, glass doors, and other surfaces are hot during operation AND cool down.

Hot screen/mesh and glass doors will cause burns.

  • Do not touch screen/mesh or glass doors until cooled
  • NEVER allow children to touch screen/mesh or glass doors
  • Keep children away
  • CAREFULLY SUPERVISE children in the same room as the fireplace.
  • Alert children and adults to the hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

  • Keep clothing, furniture, draperies, and other flammable materials away.

CAUTION! The door kit is heavy. We recommend two installers to put the front assembly in place.

Installation

  1. Remove the existing screens from the fireplace. See Figure 2:
    • Remove one screw in each of the screen rods behind the upper screen cover
    • Slide screen rods out of support holes.
    • Rods and screens will come out as an assembly.
    • Discard.HEARTH-HOME-technologies-ASD-Series-Mesh-Door-Kits-fig- \(3\)
  2. Install the inner hood by using the (4) bend tabs to locate it. Pry up hand band tables slightly to locate. See Figure
  3. Use the (2) screws from the screen rods to secure them into place. See Figure 5. Leave the original hood in place.HEARTH-HOME-technologies-ASD-Series-Mesh-Door-Kits-fig- \(4\)
  4. Hang the door frame assembly into the (4) slots located on the firebox (see Figure 2) with the corresponding hooks on the door frame. See Figure 4. Be sure the door is all the way down on the hooks. The door frame will have approximately a 1/2 inch gap on the bottom of the frame. See Figure 6.HEARTH-HOME-technologies-ASD-Series-Mesh-Door-Kits-fig- \(5\)

Hearth & Home Technologies Outdoor Mesh Doors 4136-918 Rev B 04/23

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

HEARTH HOME technologies User Manuals

Related Manuals