BEA EAGLE FAMILY Motion Sensor Instruction Manual

BEA EAGLE FAMILY Motion Sensor

Product Information:

The product is part of the Eagle family accessories and includes the following items:

• Rain Cover 10ERC
• Rain Accessory 10ERA
• Mounting Bracket 10EMB
• Ceiling Accessory 10ECA
• Spacer 10EAGLESPACER
• Eagle Spacer V 10EAGLESPACERV

The product is designed to be installed in public areas and complies with applicable safety standards, such as ANSI A156.10.
For full sensor installation and setup instructions, refer to the EAGLE User’s Guide (75.5601) or EAGLE HIGH-MOUNT User’s Guide (75.5611). For technical support and customer service, contact 1-800-523-2462 or email techservices- us@BEAsensors.com.

Product Usage Instructions

1. Pre-drill the EAGLE Harness passage hole using a 1/4″ drill bit for SPACER and a 1/2″ drill bit for SPACER V.
2. Route the EAGLE Harness through the wall/header and then through the designated pass-thru on the spacer.
3. If using EAGLE SPACER V, route its camera harness through the wall/header and plug it into the SPACER V connector.
4. Mount the spacer to the wall/header using self-drilling screws.
5. Route the EAGLE Harness through the pass-thru on the sensor.
6. Mount the sensor to the accessory.
7. Wire the EAGLE Harness to the sensor.

Note: The product includes a camera (EAGLE SPACER V only) with the following technical specifications:

• Video output: 1.0 (Vp-p) / 75
• Image Sensor: CMOS
• Horizontal resolution: 480 TVL
• NTSC output: Sync system: Inter-Sync
• Frame rate: 30 fps
• Min. illumination: 0.01 LUX
• AE control: auto
• Gain control: auto
• Elec. shutter: 1 s ~ 1/10,000 s
• S/N ratio: > 50 dB
• AWB: auto

Visit website for available languages of this document.

EAGLE FAMILY ACCESSORIES

PRECAUTIONS

• Maintain a clean and safe environment when working in public areas.
• Constantly be aware of pedestrian traffic around the door area.
• Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door.
• Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation.

Reference EAGLE User’s Guide (75.5601) or EAGLE HIGH-MOUNT User’s Guide (75.5611) for full sensor installation and setup

BEA, INC. INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS

BEA, Inc., the sensor manufacturer, cannot be held responsible for incorrect installations or incorrect adjustments of the sensor/device; therefore, BEA, Inc. does not guarantee any use of the sensor/ device outside of its intended purpose.
BEA, Inc. strongly recommends that installation and service technicians be AAADM-certified for pedestrian doors, IDA-certified for doors/gates, and factory-trained for the type of door/gate system.
Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring that the sensor/device system performance is compliant with local,national, and international regulations, codes, and standards.
Once installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer’s recommendations and/or per AAADM/ANSI/DASMA guidelines (where applicable) for best industry practices. Safety inspections must be performed during each service call – examples of these safety inspections can be found on an AAADM safety information label (e.g. ANSI/DASMA 102, ANSI/DASMA 107, UL294, UL325, and International Building Code).
Verify that all appropriate industry signage, warning labels, and placards are in place.

INSTALLATION

SPACER / SPACER V 10EAGLESPACER / 10EAGLESPACERV

1. Pre-drill the EAGLE Harness passage hole (1⁄4” for SPACER, 1⁄2” for SPACER V).
2. Route the EAGLE Harness through the wall/header and then through the designated pass-thru on the spacer.
3. Route the EAGLE SPACER V camera harness through the wall/header and then plug into SPACER V connector.
4. Mount the spacer to wall/header using self-drilling screws.
5. Route the EAGLE Harness through the pass-thru on the sensor.
6. Mount sensor to accessory.
7. Wire the EAGLE Harness to the sensor.

CAMERA TECHNICAL SPECIFICATIONS

Voltage regulator

(built into wire harness):

| 6.6 – 36 VDC (±10%)

6 – 28 VAC (±10%)

---|---
Operating temperature:| -30 – 60 °C (max. RH: 95%)
Video output:| 1.0 (Vp-p) / 75Ω
Image Sensor:| CMOS
Horizontal resolution:| 480 TVL
NTSC output:| 720 (H) × 480 (V)
Sync system:| Inter-Sync
Frame rate:| 30 fps
Min. illumination:| 0.01 LUX
AE control:| auto
Gain control:| auto
Elec. shutter:| 1 s ~ 1/10,000 s
S/N ratio:| > 50 dB
AWB:| auto

Tech Support & Customer Service: 1-800-523-2462
General Tech Questions: techservices-us@BEAsensors.com
Tech Docs: www.BEAsensors.com

©BEA  Original Instructions
75.5981.05 EAGLE FAMILY ACCESSORIES 20230904

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>