BEA 75.5899.02 Mounting Box User Guide
- June 1, 2024
- BEA
Table of Contents
BEA 75.5899.02 Mounting Box
Product Information
Specifications
- Dimensions: 5 3/8 (L) x 5 3/8 (W) x 2 (T)
- Material: Box – ABS plastic, Locking screw – stainless steel
Product Usage Instructions
Installation
- Remove the locking screw.
- Slide the box off the mounting plate.
- Mount the mounting plate to a wall or other flat surface.
- Install the push plate to the box.
- Connect the wireless transmitter to push plate NO and COM.
- Slide the box onto the mounting plate.
- Reinstall the locking screw.
Battery Replacement
- Remove the locking screw.
- Slide the box off the mounting plate.
- Replace wireless transmitter batteries.
- Slide the box onto the mounting plate.
- Reinstall the locking screw.
Notes: Compatible with any BEA wireless transmitter. Refer to the specific User’s Guide for battery information.
FAQ
Q: Can I use any wireless transmitter with this mounting box?
A: Yes, the mounting box is compatible with any BEA wireless transmitter. Refer to the specific User’s Guide for battery information.
Q: What should I do if I encounter unexpected reactions by the door during tests?
A: Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door. Ensure compliance with all applicable safety standards upon completion of installation.
OVERVIEW
- mounting plate
- box
- locking screw (Phillip’s head)
TECHNICAL SPECIFICATIONS
- Dimensions 5 3 ⁄8” (L) x 5 3 ⁄8” (W) x 2” (T)
- Material box: ABS plastic
- locking screw: stainless steel
- Specifications are subject to change without prior notice.
- All values are measured in specific conditions.
COMPATIBLE PRODUCTS
The following 4.75” square push plates and accessories are compatible with the Mounting Box EBA:
- 10PBS – PUSH TO OPEN text only
- 10PBS1 – PUSH TO OPEN text and accessibility logo
- 10PBSLL – accessibility logo only
- 10PBS10 – plain
- 10PBSE – PUSH TO EXIT text only
- 10PBS1B – PUSH TO OPEN text and accessibility logo, blue
- 10PBS1SB – PUSH TO OPEN text and accessibility logo, satin brass
- 10PBS1BB – PUSH TO OPEN text and accessibility logo, bright brass
- 10WRSQ475 – weather ring
PRECAUTIONS
CAUTION
- Shut off all power going to the header before attempting any wiring procedures.
- Maintain a clean and safe environment when working in public areas.
- Constantly be aware of pedestrian traffic around the door area.
- Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door.
- ESD (electrostatic discharge): Circuit boards are vulnerable to damage by electrostatic discharge. Before handling any board, ensure you dissipate your body’s ESD charge.
- Always check the placement of all wiring before powering up to ensure that moving door parts will not catch any wires and cause damage to equipment.
- Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation.
- DO NOT attempt any internal repair of the components. All repairs and/or component replacements must be performed by BEA, Inc. Unauthorized disassembly or repair:
- May jeopardize personal safety and may expose one to the risk of electrical shock.
- This may adversely affect the safe and reliable performance of the product resulting in a voided warranty.
INSTALLATION
- Remove locking screw
- Slide the box off of the mounting plate
- Mount mounting plate to wall or other flat surfaces.
- Install a push plate to the box.
- Connect the wireless transmitter to push plate NO and COM.
- Slide the box onto the mounting plate.
- Reinstall the locking screw.
BATTERY REPLACEMENT
- Remove locking screw
- Slide the box off of a mounting plate.
- Replace wireless transmitter batteries.1
- Slide the box onto the mounting plate.
- Reinstall the locking screw.
NOTES:
Compatible with any BEA wireless transmitter. Refer to the specific User’s Guide for battery information.
BEA, INC. INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS
- BEA, Inc., the sensor manufacturer, cannot be held responsible for incorrect installations or incorrect adjustments of the sensor/device; therefore, BEA, Inc. does not guarantee any use of the sensor/device outside of its intended purpose.
- BEA, Inc. strongly recommends that installation and service technicians be AAADM-certified for pedestrian doors, IDA-certified for doors/gates, and factory-trained for the type of door/gate system.
- Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring that the sensor/device system performance is compliant with local, national, and international regulations, codes, and standards.
- Once the installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer’s recommendations and/or per AAADM/ANSI/DASMA guidelines (where applicable) for best industry practices. Safety inspections must be performed during each service call – examples of these safety inspections can be found on an AAADM safety information label (e.g.
- ANSI/DASMA 102, ANSI/DASMA 107, UL294, UL325, and International Building Code).
- Verify that all appropriate industry signage, warning labels, and placards are in place.
- Tech Support: 1-800-407-4545 | Customer Service: 1-800-523-2462 General Tech Questions: techservices-us@BEAsensors.com www.BEAsensors.com
- 75.5899.02 MOUNTING BOX EBA 20240315
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>