LEXON LH95 Steli Felt Atmosphere Lamp User Manual

LEXON LH95 Steli Felt Atmosphere Lamp

Product Information

• Product Name: Steli
• Dimensions: 90 mm x 240 mm
• Model: LH95
• Designers: Manuela Simonelli & Andrea Quaglio
• Included in the Box:
  • 1x Steli Lamp
  • 1x USB Type-C Charging Cable
  • 1x User Manual

Product Usage Instructions

Charging

We recommend fully charging the battery before using Steli for the first time. The initial full charge can be done via USB charging, which takes approximately 3 hours, or via wireless charging, which takes around 4 hours.

Charge with USB cable

1. Plug the provided USB Type-C cable into the charging port of Steli.
2. Plug the USB end of the cable into any computer or any DC 5V power supply charger.

Charge with Wireless Charger

Steli has a built-in wireless charging receiver. To charge the battery using a wireless charger:

1. Place Steli at the center of the wireless charger.
2. Disconnect the device once the battery has been fully charged.

Operating Instructions

Setting up one Steli lamp

To set Steli in cool and warm light mode only, quickly tap 3 times on the top area. To return to full set lighting mode, repeat the procedure.

Pairing several Steli lamps (Interconnection network)

Pairing Steli with one or multiple Steli lamps does not require any third- party software/device. To enjoy the multiple bulbs synchronization feature, follow the instructions below:

1. Press and hold the BT button at the bottom of each lamp for 3 seconds to turn ON the communication module. The Blue LED will start flashing.
2. Select one of the lamps and press the BT button twice to initiate the multi-pairing procedure. Once the procedure is complete, all lamps will be on the same color setting. The lamp used for connection is now identified as the MASTER in the system, its LED will keep flashing while others are turned OFF. You can now interact from any lamp to change the color, adjust brightness, or turn ON & OFF all lamps at once.

Add one or more Steli lamps to the network

1. To add one or more Steli lamps to the network, simply turn them ON by pressing and holding the BT button on each unit for 3seconds.
2. Press once on the pairing button of any lamp from the existing network (repeat the procedure with any new device).

Exclusive LOCK NETWORK feature

Steli is equipped with a unique locking system that allows only one lamp to control all others, preventing any change of color, brightness, or even turning ON/OFF from any other lamp in the network. The main lamp (MASTER) is the only one that can control the network. All other lamps become SLAVES. To enable the LOCK function, take the MASTER unit and follow the instructions below:

1. Press 5 times on the BT MASTER device button, it will send a signal to ALL other lamps to LOCK.
2. In LOCK mode, only the MASTER can interact with other lamps. Its LED will double flash every 3 seconds.
3. The network can be unlocked by quickly pressing 5 times on the BT button from the MASTER lamp.

PRODUCT OVERVIEW

1. Tane area Lighing luncion)
2. Lamp
3. BT Button (connection between Steli lamps)
4. Reset kev
5. Receiver for wireless charging
6. LED indicator (battery & charging
7. UB Typet hating & charging status)

FEATURES

• LED technology with 9 colors (warm white, cold white, blue, yellow, green, red, purple, light pink & light blue)
• Dimmable LED lights with memory system
• Interconnectable LED lamp (Bluetooth mesh network)
• Suitable for outdoor use (IPX4)
• Rechargeable via wireless charging or USB Type-C

CHARGING
We recommend you to fully charge the battery before using Steli for the first time. The initial full charge should take approximately 3 hours via USB charging and 4 hours via wireless charging

lED-Informationen

Charge with USB cable

1.  Plug the provided USB Type-C cable into the charging port of Steli.
2.  Plug the USB end of the cable into any computer or any DC 5V power supply charger.

Charge with Wireless Charger

Steli has a built-in wireless charging receiver. You can charge the battery by using a wireless charger.

1.  Place Steli at the center of the wireless charger.
2. Disconnect the device once the battery has been fully charged

OPERATING INSTRUCTIONS

Setting up one Steli lamp

• Touch the top of the lamp to turn it ON.
• There are 9 colors options you can select by simply touching the top of the lamp.
• To adjust brightness, touch the top area until you reached the desired brightness then release.
• To turn OFF the light, wait 3 seconds after the color selection then touch again. The last color set will be remembered for next time

Note: If you want to set Steli in cool and warm light mode only, quickly tap 3 times on the top area. To return to full set lighting mode,
repeat the procedure

Pairing several Steli lamps (Interconnection network)
Pairing Steli with one or multiple Steli lamps does not require any third- party software/device. To enjoy the multiple bulbs synchronization feature, follow below instructions:

1.  Press and hold the BT button at the bottom of each lamp for 3 seconds to turn ON the communication module. The Blue LED will start flashing.
2.  Select one of the lamps and press the BT button twice to initiate the multi-pairing procedure. Once procedure is complete, all lamps will be on the same color setting. The lamp used for connection is now identified a MASTER in the system, its LED will keep flashing while others are turned OFFYou can now interact from any lamp the change the color, adjust brightness or turn ON & OFF all lamps at once.

Important not Bluetooth will automatically turn off after the lamp has been off for 60 minutes. If you enable the Bluetooth® on one of your lamps to connect it to the network, but do not complete the pairing, the lamp’s Bluetooth mode will turn off after 3 minutes automatically

Add one or more Steli lamps to the network

1.  To add one or more Steli lamps to the network, simply to it (them) ON by pressing and holding the BT button on each unit for 3 seconds.
2.  Press once on the pairing button of any lamp from the existing network (repeat the procedure with any new device

Exclusive LOCK NETWORK feature
Steli is equipped with a unique locking system allowing only One lamp to control all others, preventing any change of color, brightness or even turn ON/OFF to be made from any other lamp in the network. The main lamp (MASTER) is the only one to control the network. All other lamps are becoming SLAVES. To enable LOCK function, take the MASTER units and follow below instructions:

1.  Press 5 times on the BT MASTER device button, it will send signal to ALL other lamps to LOCK.
2. In LOCK mode, only MASTER interact with other lamps. Its LED is double flashing every 3 seconds.
3. Network can be unlocked by quickly pressing 5 times on the BT button from the MASTER lamp

To change the MASTER device

1. Make sure the network is UNLOCKED
2. Quickly Press the BT button on any device for 10 times, this device will become the new MASTER device.You can now LOCK and UNLOCK the network from this new device.

Important note  In LOCKED/UNLOCKED network mode, it is strongly recommended to always keep the MASTER device in
charge or fully charged to get the best experience and avoid loss of control of the entire network

Other working operations

• To turn OFF ALL the lamps when the network is locked, double tap on the top of the MASTER device. You’ll need to tap on the MASTER again to turn all lamps back ON.
• To turn OFF only one lamp when the network is locked, long press on the BT button from more than 15 seconds until the lamp turns OFF. (This will remove the lamp from the network. Repeat the pairing procedur  above to bring it back to the network)
• To reset the lamp, insert a thin object into the hole (4) under the lamp and press the key inside. A manual reset allows you to reboot your device and correct miscellaneous bugs (unrecognized device, unstable Bluetooth connection…).

LED Information

SAFETY PRECAUTIONS

• IPX4 water resistant device, resistant to rain, splash, and spray water.
• Never immerse your device in water to avoid internal short circuit, overheating, fire, deformation or even explosion of the battery.
• Do not store your device in very hot or cold areas. It is recommended to use your device at room temperatures.
• Do not attempt to service, repair or disassemble the device yourself.
• Make sure to respect the technical specifications for charging and never use a power adapter delivering more voltage output than the one indicated to avoid any irreversible damage to the internal circuit (DC Input: 5V)
• Do not place the Steli case on the wireless charger when conductive materials, such as metal objects and magnets, are placed between the Steli case and the wireless charger. Use only certified wireless chargers.

PRODUCT SPECIFICATIONS

• Material  Aluminium/ABS
• Weight 135 g / 0.29 lbs
• Dimensions
• Max lumen output 120 lm
• Color temperatur
• Warm white 2700K
• Cold white  6500K
• Battery voltage
• Charging time (wirelessly) approx. 4 hours
• Operating temperature :0°C – 35°C
  *may vary based on product use, set light intensity and selected light color
• Bluetooth® range :10m
• Frequency range: 2402M-2480MHZ
• Input port  DC 5V
• Wireless input 5W
• Battery type  Li-polymerb: 1500 mAh
• Charging system :USB Type-C or Supports wireless charging ˜°˛

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>