LUTRON DVRF-PKG1D-WH Caseta Wireless Diva Smart Dimmer Expansion Kit User Guide

quick-start guide
Diva Smart Dimmer and
Pico Paddle Remote

0302106 Rev. A

DVRF-PKG1D-WH Caseta Wireless Diva Smart Dimmer Expansion Kit

Welcome— and thank you for purchasing a Diva smart dimmer and Pico paddle remote kit.

Wiring Wizard

https://qrco.de/bdmspI

Find the right LED

http://www.lutron.com/ledfinder

Double your warranty
Love Caséta Wireless controls? Have ideas for making them better? Tell us what you think and we’ll extend your warranty by 1 year. www.casetawireless.com/register

Contents supplied (DVRF-PKG1D)

Tools you’ll need

Works with energy efficient dimmable light bulbs:

| LED—up to 150 W
---|---
| Incandescent—up to 600 W
| Halogen—up to 600 W

NOTE: You can mix and match dimmable LED and CFLs, as well as halogen and incandescent light bulbs with Caséta dimmers.
Dimmable LED and CFL light bulbs vary in their dimming performance. If you’re using these bulbs and they flicker or unexpectedly turn off, please see the “Adjusting low-end trim” section on page 2 for information on adjusting the dimmer for best bulb performance.

Ganging and Derating

Important note:
Multi-gang installations may reduce the dimmer’s maximum wattage rating. See the chart below for maximum wattage information.
*Maximum wattage derating chart (120 V~ 50/60 Hz)**

**or***
Incandescent & Halogen| 600 W| 500 W| 400 W

• For maximum wattage information when mixing light bulb types see www.casetawireless.com/ganging

Pre-Installation

Identify installation type

| Option 1: Wireless 3-Way / Single-Pole + Pico Paddle Remote
---|---
| Option 2: Wireless 3-Way / Replace Mechanical 3-way Switch with the Pico Paddle Remote
| Option 3: Wireless Multi-Location / Retain Mechanical 3-Way Switch +
Pico Paddle Remote
| Option 4: Wired Multi-Location [3-Way / 4-Way with Accessory Switch(es)] + Pico Paddle Remote

Installing your in-wall dimmer (main location)

Disconnect power
WARNING: SHOCK HAZARD.
May result in serious injury or death.
Turn off power at circuit breaker or fuse before installing.

Important wiring note:
Some lights have one wall switch— called single-pole, while others have two wall switches— called 3-way (such as stair lights, which have a switch at both the top and bottom of the stairs). Be sure to pay close attention to the appropriate wiring diagrams in the following steps.
To access more detailed information and step-by-step instructions for specific wiring scenarios please use the “Wiring Wizard” QR code to the left.

Option 1: Wireless 3-way /single pole + Pico paddle remote

For lights switched from one wired location:
NOTE: Red and black wires on dimmer are interchangeable.

Option 2: Wireless 3-way / replace mechanical 3-way switch with the Pico paddle remote
For lights switched from one wired location and one wireless location:
IMPORTANT: Before disconnecting the existing devices, tag the wire connected to the different colored screw (typically a black wire, but wire colors vary, and labeled COM). This is the Common wire.

Option 3: Wireless multi-location / retain mechanical 3-way switch + Pico paddle remote
For lights switched from two wired locations with a wireless control from one or more remote locations: Follow the “Wiring Wizard” QR code for detailed instructions.

https://qrco.de/bdmspI

Option 4: 3-way/4-way with Claro smart accessory switch(es) + Pico paddle remote
For lights switched from two or more wired locations with a wireless control from one or more remote locations: See Claro Smart Accessory Switch Installation Guide (model DVRF-AS) for details on installing accessory switches. See section A, “Over Wallbox Installation” for replacing any switch location with a Pico paddle remote.
See section B, “Wall Surface Installation” for adding additional points of control using the Pico paddle remote.

Installing your Pico paddle remote (secondary location)

A. Over Wallbox Installation replacing existing switch (3-way applications) with Pico paddle remotes

1. Ensure power is still OFF
   WARNING! Shock Hazard.
   May result in serious injury or death. Turn off the power before installing. NOTE: If the wallbox adapter cover plate is removed, only install over wall surface. DO NOT install over wallbox.

2. Unscrew existing switch from wall
   Remove the wallplate.
   Remove the screws securing the switch and pull it away from the wall (do not disconnect wires).

3. Disconnect wires
   

4. Connect the wires
   Using the provided wire connectors, connect the wires together (EXCEPT for the ground wire and the neutral wires). Cap the ground wire and cap the neutral wires.
   

5. Mount the wallbox adapter
   

6. Slide Pico paddle remote onto wallbox adapter
   

7. Attach wallplate
   If wallplate removal is necessary, pull forcefully.

8. Restore power
   

B. Wall Surface Installation

1. Remove cover plate
   

2. Mark wall and drill holes
   

3. Mount the wallbox adapter
   

4. Slide Pico paddle remote onto wallbox adapter

5. Attach wallplate
   If wallplate removal is necessary, pull forcefully.

6. Check mounting
   Side View
   

7. Restore power

To Use your Caséta by Lutron System

Option 1: With a smartphone or tablet (smart hub required, sold separately)
The Diva smart dimmer can be controlled from a smartphone when used with the Lutron smart hub (formerly smart bridge) and the Lutron app.
If you are using the dimmer and remote control with the Lutron smart hub follow the instructions below.

1. Download the Lutron app
   

https://qrco.de/bdiw9z

2. Launch the Lutron app
   

3. Use the Lutron app to complete ALL remaining steps
   

Option 2: Without a smartphone or tablet (smart hub not required)
Pairing the dimmer and Pico paddle remote
Note: This setup MUST be completed if you are not using a smart hub. The Diva smart dimmer and Pico paddle remote are not paired from the factory.

1. Press and hold “off” button on dimmer
   

2. Press and hold “off” button on the Pico paddle remote
   For advanced features, tips for using Caséta dimmers with LEDs and CFLs, the complete Caséta product line, and more, please visit www.casetawireless.com/features

Troubleshooting

bulb(s) burned out.
• Breaker is OFF or tripped.
• Light not properly installed.
• Wiring error.
• FASS switch on the dimmer is in the Off position.
Light does not respond to Pico remote.| • The dimmer failed to pair with Pico remote; see Pairing the dimmer and Pico paddle remote.
• The dimmer is already at the light level the Pico remote is sending.
• The Pico remote is outside the 30 ft (9 m) operating range.
• The Pico remote battery is low.
• The Pico remote battery is installed incorrectly.
•  Bulbs turn off while being dimmed.
•  Bulbs turn on at high light level but do not turn on at a low light level.
•  Bulbs flicker or flash when dimmed to a low light level.| Verify bulbs are marked dimmable and see the Adjusting low-end trim section for information on adjusting the dimmer for
best bulb performance.
Load is Off and the light bar blinks 4 times, pauses, and repeats.| The dimmer is in Over Temperature Protection (OTP) mode.
• See Ganging and Derating. Ensure the dimmer is not overloaded.
• Reset the dimmer by using the Front Accessible Service Switch (FASS); See Using your dimmer section. Pull out the FASS and push it back in.

Go to www.casetawireless.com/support for additional troubleshooting suggestions.

Using your dimmer

Replacing light bulbs using FASS
Pull the FASS switch out on the in-wall dimmer to remove power at the light socket.

Important notes:

1. For indoor use only.
2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C).

Adjusting low-end trim

1. Pull the Front Accessible Service Switch (FASS) out to the open position.
2. Press and HOLD the Off button.
3. Continue to HOLD the Off button and push the FASS in until the light bar flashes.
4. Release the Off button and adjust the slider to desired low-end brightness.
5. Press Off to save settings.

CAUTION
Use only with permanently installed fixtures with dimmable LED, dimmable CFL, halogen, or incandescent lamps. To avoid overheating and possible damage to other equipment, do not use to control receptacles, motor-driven appliances, or transformer-supplied appliances.
CAUTION: Risk of Fire, Explosion, Leakage, and Burns. Do Not Recharge, Disassemble, Heat Above 212 °F (100 °C) or Incinerate. This product contains a lithium button/coin cell battery. Keep batteries away from children. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep the batteries away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. The battery in this device contains Perchlorate Material — special handling may apply. For more information, visit www.dtsc.ca.gov/hazardouswaste/perchlorate

Codes
Install in accordance with all national and local electrical codes.

Grounding
When no “grounding means” exist in wallbox, the National Electrical Code (NEC®) allows a control to be installed as a replacement if 1) a nonmetallic, noncombustible faceplate is used with nonmetallic attachment screws or 2) the circuit is protected by a ground fault circuit interrupter (GFCI). When installing a control according to these methods, cap or remove green wire before screwing control into wallbox.

FCC / IC Information
This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. Modifications not expressly approved by Lutron Electronics Co., Inc. could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Device Ratings
In-wall dimmer
DVRF-6L 120 V~ 50/60 Hz
Pico paddle remote
PJ2-P2B
3 V 10 mA (1) CR2032 battery (included)

Lutron, Lutron, Claro, Caséta, Pico, the Caseta logo, the design of the Diva dimmer, Diva and FASS are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries.
All other product names, logos, and brands are property of their respective owners.
© 2023 Lutron Electronics Co., Inc.

References

• Application Notes | Caséta Wireless | Lutron
• Capacity Derating Charts
• casetawireless.com/register
• Application Notes | Caséta Wireless | Lutron
• dtsc.ca.gov/hazardouswaste/perchlorate

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>