tern HSD Gen 1 Electric Bike Instruction Manual
- June 13, 2024
- tern
Table of Contents
tern HSD Gen 1 Electric Bike
Product Information:
DuoStandTM
The DuoStandTM is a bike stand designed to provide stability and support when parking your bike. It is compatible with HSD Gen 1, HSD Gen 1A, HSD Gen 2, Quick HaulTM, and Short HaulTM frames. The stand has a load limit of 80 kg (176 lb), which includes the weight of the bike.
What’s Included
The DuoStandTM Kit includes the following parts:
- DuoStandTM
- Flat Plate
- (Additional parts required for HSD Gen 1, sold separately)
Tools Required (Not Included)
In order to install the DuoStandTM, you will need the following tools:
- Tool to remove existing kickstand (may differ depending on your bike)
- M10 x 30 Bolt
- M10 x 45 Bolt (required for HSD Gen 1A)
- Nut
- Washer
Product Usage Instructions:
DuoStandTM
Installation
- Apply anti-seize lubricant to the tip of the bolts before securing the nuts. If anti-seize lubricant is not available, apply any standard lubricant to reduce friction and prevent thread galling.
- Remove the existing kickstand using the appropriate tool for your bike.
- Follow the assembly order below based on your bike’s frame type:
For HSD Gen 2 / Quick HaulTM / Short HaulTM Owners
Assembly Order:
- Nut
- Washer
- Bike
- DuoStandTM
- Washer
- M10 x 30 Bolt
For HSD Gen 1 Owners
Before installation, identify the HSD frame by the kickstand mount located in front of the rear wheel. Additional parts are required for HSD Gen 1, see “Additional Parts Required for HSD Gen 1”.
Assembly Order:
- Nut
- Washer
- Wing-shaped Plate* (Not Included)
- Bushing* (Not Included)
- Bike
- Flat Plate* (Not Included)
- DuoStandTM
- Washer
- M10 x 45 Bolt* (Not Included)
For HSD Gen 1A Owners
Assembly Order:
- Nut
- Washer
- Bike
- Flat Plate* (Not Included)
- DuoStandTM
- Washer
- M10 x 30 Bolt
Adjusting the DuoStandTM Height
- The recommended clearance from the bottom of the rear wheel to the ground is 5 – 10 mm (3/16 – 3/8). Measure the distance from the bottom of the rear tire to the ground and adjust the height of the DuoStandTM by loosening the bolts on the DuoStand Ends to raise or lower the legs. Tighten the bolts to a torque of 8 – 9 Nm.
Note: Optional LockstandTM Extensions are available for purchase from your local Tern dealer to provide maximum stability when parked.
For more information and support resources, visit ternbicycles.com/support.
Manual Version 01
Make sure you have the latest support resources!
Visit ternbicycles.com/support for:
Safety
If you are unsure how to install this product, please visit your local dealer.
Do not exceed the load limit of 80 kg (176 lb). Please remember the max load
limit includes the weight of the bike.
Never leave children or pets on a parked bike unattended.
What’s Included
- DuoStand
- M10 x 30 Bolt x 2
- M10 Washer x 4
- M10 Nut x 2
Additional Parts Required for HSD Gen 1
If you have an HSD Gen 1, please see the instructions on the next page to determine which HSD frame your bike comes with.
- The DuoStand HSD Kit and Flat Plate are required to install the DuoStand on the HSD Gen 1.
- The Flat Plate* is required to install the DuoStand on the HSD Gen 1A.
DuoStand HSD Kit
- M10 x 45 Bolt x 2
- Bushing x 2
- Wing-shaped Plate
Each sold separately
Tools Required (Not Included)
- 17 mm Hex Socket x 1
- 17 mm Wrench x 1
- 3, 4, or 5 mm Allen Wrench for removing the existing kickstand. (Tool size may differ depending on your bike.)
Installation
Add anti-seize lubricant to the tip of the bolts before securing the nuts. If anti-seize lubricant is not available, apply any standard lubricant to reduce friction and prevent thread galling.
- Remove the existing kickstand. (Tool may differ depending on your bike.)
- Install Bolt Sets in the order and arrangement shown below.
For HSD™ Gen 2 / Quick Haul™ / Short Haul™ Owners
Assembly Order
- Nut
- Washer
- Bike
- DuoStand
- Washer
- M10 x 30 Bolt
For HSD Gen 1 Owners
Identify the HSD Frame
Before installation, identify the HSD frame by the kickstand mount located in
front of the rear wheel.
Additional parts are required to install the DuoStand on the HSD Gen 1. See the Additional Parts Required for HSD Gen 1.
HSD Gen 1 Assembly Order
- Nut
- Washer
- Wing-shaped Plate*
- Bushing*
- Bike
- Flat Plate*
- DuoStand
- Washer
- M10 x 45 Bolt*
Not Included.
HSD Gen 1A Assembly Order
- Nut
- Washer
- Bike
- Flat Plate*
- DuoStand
- Washer
- M10 x 30 Bolt
Not Included.
The recommended clearance from the bottom of the rear wheel to the ground is 5 – 10 mm (3/16″ – 3/8″). Measure the distance from the bottom of the rear tire to the ground and adjust the height of the DuoStand by loosening the bolts on the DuoStand Ends to raise or lower the legs. Tighten the bolts to a torque of 8 – 9 Nm.
Optional: Install Lockstand™ Extensions
For maximum stability when parked, install the Lockstand Extensions. Available for purchase from your local Tern dealer.
LIMITED PRODUCT WARRANTY INFORMATION: This Product comes with a ONE (1)
YEAR Limited Warranty from the date of retail purchase by the original end-
user. If a material or workmanship defect arises and a valid claim is received
within the Warranty Period, this Product will be replaced.
Mobility Holdings cannot be held liable for damages to personal property due
to misuse or improper care and maintenance. This Product Warranty does not,
under any circumstance, cover the replacement or cost of any third party
product used with or connected to the Product.
Tern, the Tern Werd (logotype), the Tern Berd (device), Lockstand, DuoStand,
HSD, Quick Haul, and Short Haul used alone or in combination are trade names,
trade devices or registered trademarks of Mobility Holdings, Ltd.
© 2024. Tern is a trademark of Mobility Holdings, Ltd. All Rights Reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>