BELLEVUE 597PHM Seedy Glass Samathra 12 Inch Tall Pier Mount Post Light Instruction Manual

BELLEVUE 597PHM Seedy Glass Samathra 12 Inch Tall Pier Mount Post Light

Product Information

This product is a fixture assembly kit that includes various models:

• 597PHM, 599PHM, 597PHB, 599PHB, 597MP3, 599MP3, 597BP3, 599BP3, 597MP6, 599MP6, 597BP6, and 599BP6.

It comes with installation and operation instructions, and certain tools and materials are required for assembly:

• Screwdriver
• Wire Cutters
• Adjustable Wrench
• Wiring Supplies

Prior to assembly, it is important to refer to the ELECTRICAL CONNECTIONS section in the manual. If you lack electrical wiring experience, it is recommended to consult a do-it-yourself wiring handbook or hire a qualified licensed electrician for fixture installation.

Caution:
LED fixtures can operate at high temperatures, so it is advised to use caution when touching them during or after operation.

Product Usage Instructions

1. Turn off the electricity before starting the assembly process.
2. Prepare the fixture according to the provided instructions.
3. Follow the final assembly steps to complete the installation.
4. When handling the fixture during or after operation, be cautious of the high temperatures it may generate.
5. Use the Post Fitter Screw and Base components as specified in the manual.
6. Connect wires using the Wire Connector.
7. Secure the fixture in place using the Wood Screw Anchor Sleeve.

SAFETY WARNING

BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF. GENERAL You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag-type fixture be installed on a ceiling that contains a radiant-type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician. NOTE: Proper wiring is essential for the safe operation of this fixture.

ASSEMBLY INSTRUCTIONS

• 597PHM & 599PHM & 597PHB & 599PHB & 597MP3 & 599MP3 & 597BP3 & 599BP3 & 597MP6 & 599MP6 & 597BP6 & 599BP6

TOOLS & MATERIALS REQUIRED

• Screwdriver Wire Cutters
• Adjustable Wrench Wiring Supplies

CAUTION
Prior to assembly, refer to the ELECTRICAL CONNECTIONS section. If you do not have electrical wiring experience, refer to a do-it-yourself wiring handbook or have your fixture installed by a qualified licensed electrician.

GENERAL

1. Be sure to read these instructions and review the diagrams thoroughly before beginning.
2. Electrical connections must be in accordance with local codes, ordinances, or the National Electric Code. If you are unfamiliar with methods of installing electrical wiring, secure the services of a qualified licensed electrician.
3. Before starting the installation, disconnect the power by turning off the circuit breaker or by removing the appropriate fuse at fuse box. Turning the power off at the light switch is not sufficient to prevent electrical shock.

NOTE: First turn off the electricity

FINAL ASSEMBLY**** ELECTRICAL CONNECTIONS

1. Pull the black, white, and ground wires out of the mounting post.

2. While supporting the fixture, connect electrical wires. If your post has a ground wire (green or bare copper), connect the fixture ground wire to it. If not, consult your electrician for proper grounding.
   ELECTRICAL CONNECTIONS 120V~, 60Hz
   Connect white wire(s) from the fixture to white neutral wire from the supply circuit. Connect black wire(s) to black hot wire from the supply circuit. Connect green wire to green or bare wire or grounding screw on the mounting bracket. In all cases grounding conductor to earth must be used. Use UL/CSA Listed wire connects suitable for the size, type, and number of conductors. No loose strands or loose wires should be present. Secure wire connectors with UL/CSA-listed electrical tape.
   After the wires are connected, tuck them carefully inside the post cup.

3. Align the lantern with the mounting post and secure it with screws

4. Installation is complete. Turn on the power at the circuit breaker or fuse box. Turn the light switch on to activate the fixture.

5. Glass replacement. Twist the glass part. Remember to add the gasket ring, and gasket packaged in the spare parts bag.

CAUTION:
LED fixtures can operate at high temperatures please use caution when touching during operation or after operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>