DIGITUS DN-95131 Gigabit Active 802.3af PoE Midspan Installation Guide
- June 13, 2024
- DIGITUS
Table of Contents
DIGITUS DN-95131 Gigabit Active 802.3af PoE Midspan
Product Information
| Component | Description |
|---|---|
| LAN | Data Input Port |
| PoE Load Indicator | Indicates PoE load status |
| PoE | Data & Power Output Port |
| Power Indicator | Indicates power status |
| AC Power Input | Power input port for the device |
Product Usage Instructions
To set up the GIGABIT ACTIVE 802.3af PoE MIDSPAN, follow the steps below:
- Connect the Data Input Port (LAN) of the MIDSPAN to your network switch or router using a data cable.
- Connect the PoE Load Indicator to the device you want to power using a data and power cable.
- Connect the Data & Power Output Port (PoE) of the MIDSPAN to the device you want to power using a data cable.
- Connect the AC Power Input of the MIDSPAN to a power source using a 100-240Vac power cable.
- Make sure the Power Indicator on the MIDSPAN is lit, indicating that it is receiving power.
Note: Ensure that the device you want to power supports IEEE 802.3af PoE standard.
Connection Diagram:
Introduction
DN-95131 is an indoor rated active PoE midspan Injector specially designed for complex backhaul and networking applications. It provides 48Vdc, 0.32A power for remote PDs over 2 pairs output. It supports both 10/100 Base-T and Gigabit device. It works for 15.4W PoE PDs, such as wireless APs, Wifi routers, Network cameras, IP Phones, Microwave Radio and other power Ethernet terminals. It fully complies to IEEE802.3af PoE standard. Enclosed in an IP40 fire retardant plastic case. It works with a wide input voltage of 100-240 VAC, 50 or 60 Hz. It has detection chip inside, which will detect and classify PD before powering it. It will not provide power until a standard-compliant PD is detected.
Main Features
- Provides 48Vdc, 0.32A power for remote PDs over 2 pairs output
- Supports both 10/100 Base-T and Gigabit device
- Works with a wide input voltage of 100-240 VAC, 50 or 60 Hz
- Easily merge of power and data cables into a single cable
- Each output port has output current limited, short-circuit protection, complete Powered Device (PD) detection and classification
- The Injector can be used independent of operating system
Package Contents
- DN-95131 PoE Injector
- Power Cord x 1
- Quick Installation Guide x 1
Technical Data
- IEEE802.3 10Base-T Ethernet
- IEEE802.3u 100Base-Tx Fast Ethernet
- IEEE802.3ab 1000Base-T Gigabit Ethernet
- Full compliant with IEEE802.3af PoE standard
- Input : 100-240Vac 0.5A 50/60Hz
- Output: 48Vdc 320mA
- Power Pins : 4/5(+), 7/8(-)
- Data Speed: 10/100/1000Mbps
- Operating Temperature: 0°C to 40°C
- Operating Humidity: 20% to 80%, non-condensation
- Storage Temperature: -20°C to 70°C
- Storage Humidity: 10% to 90%, non-condensation
- Operating Altitude: up to 2000 meters
- Case: Plastic
- Color: White
- IP Rated: IP40
- Size: 85mm x 30mm x 46mm
- Weight: 100g
- Power Indicator: Green
- PoE Load Indicator: Yellow
Product Description
- LAN: Data Input Port
- PoE Load Indicator
- PoE: Data & Power Output Port
- Power Indicator
- AC Power Input
Connection Diagram
- Wireless AP
- IPC
- 100-240Vac Power
- Switch
- DN-95131
- a. Data and power cable
- b. 100-240Vac power cable
- c. Data cable
about company
- Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address.
- www.assmann.com
- Assmann Electronic GmbH
- Auf dem Schüffel 3
- 58513 Lüdenscheid
- Germany
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>