APANTAC OG-HDBT-Rx HDMI Receiver User Manual
- June 13, 2024
- APANTAC
Table of Contents
APANTAC OG-HDBT-Rx HDMI Receiver
What is in the Box
- OG-HDBT-Rx-SET-1
- 1 x OG-HDBT-Rx-MB
- 1 x OG-HDBT-Rx-RM
Key Features
- OGX/3.0 card-based form factor.
- Dashboard control enabled.
- Supports HDBaseT Receiver input (RJ45)
- Supports HDMI 1.4 output
- RS-232 breakout
- HDCP 1.4compliant.
- Low power consumption – less than 10 W.
- 5-year limited warranty
Specifications
Description
- HDBaseT Receiver
- InputRJ45 (HDBaseT)
- Output 1 x HDMI
- RS-232 Pass through
- Cable Reach 100 meters on CAT6, 10 meters on HDMI 1.4
Rear Modules
Dashboard Control
Getting Started
The Dashboard software is designed to allow you to quickly access the feature
sets of openGear form factor cards on a simple User Interface. This section
will help you get up and running as quickly as possible.
Running Dashboard
Before you can successfully run the Dashboard software for the first time you must first download it from https://www.opengear.tv/frame-and-control /control-system/download/. Run the downloaded setup file and choose an appropriate installation location on your computer’s storage. Now you can run the Dashboard by double clicking on the Dashboard icon.
OG-HDBT-Rx Dashboard GUI
OG-HDBT-Rx is a very straightforward plug-and-play card. The Dashboard
interface only allows the identification of its product name, software
version, hardware version, and firmware version as well as the link status of
the incoming and outgoing signals.
Appendix A
COPYRIGHT, TRADEMARK, REGISTRATION
All rights reserved by APANTAC LCC, Beaverton, Oregon, USA. No part of this
document may be reproduced in any form or by any means without written
permission from the product manufacturer. Changes are periodically made to the
information in this document. They will be incorporated in subsequent
editions. The product manufacturer may make improvements and/or changes to the
product described in this document at any time. All other trademarks (s),
copyright(s), and registered technologies mentioned in this document are the
properties of their respective owner(s).
WARRANTY STATEMENT
Apantac LLC (hereinafter referred to as “Apantac”) warrants that the original purchaser of the products manufactured by Apantac (the “Product,”) will be free from defects in material and workmanship for a period of three (3) year from the date of shipment of the Product to the purchaser. If the Product proves to be defective during the three-year (3) year warranty period, the purchaser’s exclusive remedy and Apantac’s sole obligation under this warranty is expressly limited, at Apantac’s sole option, to:
- repair the defective Product without charge for parts and labor or,
- provide a replacement in exchange for the defective Product or,
- If after a reasonable time, is unable to correct the defect or provide a replacement Product in good working order, then the purchaser shall be entitled to recover damages subject to the limitation of liability set forth below.
Limitation of Liability
Apantac’s liability under this warranty shall not exceed the purchase price paid for the defective product. In no event shall Apantac be liable for any incidental, special, or consequential damages, including without limitation, loss of profits for any breach of this warranty. If Apantac replaces the defective Product with a replacement Product as provided under the terms of this Warranty, in no event will the term of the warranty on the replacement Product exceed the number of months remaining on the warranty covering the defective Product. Equipment manufactured by other suppliers and supplied by Apantac carries the respective manufacturer’s warranty. Apantac assumes no warranty responsibility either expressed or implied for equipment manufactured by others and supplied by Apantac.
This hardware warranty shall not apply to any defect, failure, or damage:
- Caused by improper use of the Product or inadequate maintenance and care of the Product.
- Resulting from attempts by those other than Apantac representatives to install, repair, or service the Product.
- Caused by installation of the Product in a hostile operating environment or connection of the Product to incompatible equipment
APANTAC LLC, 10200 SW ALLEN BLVD, BEAVERTON, OR 97005
INFO@APANTAC.COM, TEL: +1 503 968 3000, FAX: +1 503
389 7921
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>